GTO/PRO GP-SW100 - Gate Openers | Access Controls

More documents

Recommendations

Info

Setting the Limits CAUTION: Be extremely careful not to stand in the path of the gate arm while setting limits. OPEN LIMIT SETTING: 1. Turn on operator power. 2. Press and release the OPEN button on the board and be prepared to press the STOP button when the gate reached the desired open position/limit. 3. The JOG buttons can be used to bring the gate to the precise open position. The JOG buttons will slowly run the gate when pressed and stop the gate when released. 4. Once at the desired open position, press and hold the SET LIMIT button for 3 seconds or until the alarm sounds and STATUS LED is on. At this time, release the SET LIMIT button. 5. Be prepared to stop the gate when it reaches the closed position. CLOSED LIMIT SETTING: 1. If not already closed, press and release the close button. 2. Press and release the CLOSE button on the board and be prepared to press the STOP button when the gate reached the desired closed position/limit. 3. The JOG buttons can be used to bring the gate to the precise closed position. The JOG buttons will slowly run the gate when pressed and stop the gate when released. 4. Once at the desired closed position, press and hold the SET LIMIT button for 3 seconds or until the alarm sounds and STATUS LED is on. At this time, release the SET LIMIT button. 5. Open the gate to allow it to stop on its own. CYCLE 6. Open and close STALL FORCE ADJUST SAFETY the gate to verify proper operations. If limits are not set properly, redo limit setting steps above. > AUTO CLOSE TIMER NOTE: If limits are too short, use jog button to move arm short distances to stop gate at OPEN EDGE the precise open or closed position. RUN 2 OPEN CLOSE STOP CLOSE EDGE OPEN MIN MAX MIN MAX MAXOFF OFF 120 120 CLOSE LIMIT LIMIT ADJUSTMENTS SET SET >> LIMIT LIMIT STOP COM COM COM COM COM COM W1 CUT TO USE 3 BUTTON STATION <strong>GTO</strong> Inc. Tallahassee, FL SX4000 Logic Board Rev. E TEST TEST SWITCHES SWITCHES CLOSE STOP OPEN 17
Stall Force and Auto-Close Adjustments Stall Force Adjustment: IMPORTANT: For safety reasons, the STALL FORCE potentiometers are set at the “10 o’clock” position at the factory. The obstruction sensitivity is independently adjustable for each direction of travel. Upon sensing an obstruction, the gate will stop and reverse direction for approximately 2 seconds. 1. Turning the potentiometer clockwise (toward the MAX position) increases the amount of force the operator applies to an obstruction. Turning the potentiometer counter-clockwise (toward the MIN position) decreases the amount of force the operator applies to an obstruction. LOCK N.C. 2. Use a small screwdriver to adjust the appropriate potentiometer and operate the gate until it can LOCK COM run without obstructing and reversing direction. LOCK N.O. RUN 1 RUN 2 CLOSED 1 CLOSED 2 CYCLE SAFETY SHADOW SHADOW LOOP OPEN EDGE OPEN CLOSE RUN 2 EDGE OPEN CLOSE STOP COM RUNNING CLOSED LED10 LED09 CYCLE SAFETY SHADOW OPEN EDGE CLOSE EDGE OPEN CLOSE STOP COM Auto-Close COM Adjustment: COM RELAY OUTPUTS OFF OFF ON ON >>> SIMUL SLAVE SECURE DIAG. PORT OPTIONS MODE 1 MODE 2 OPEN DIR. SLV OPN DUAL MODE LOW BATT AUTO CLOSE TIMER MIN MAX MIN MAX OFF 120 SET LIMIT The Auto-Close potentiometer allows the user to set the time that the gate will stay at the open position/limit before it automatically starts to close the gate. This feature can be turned off by turning the AUTO CLOSE TIMER potentiometer all the way counter- clockwise. It is shipped from the factory in the OFF position (auto close feature is disabled). • The auto close time is adjustable from 3-120 seconds. • This feature is only enabled when the gate is at the open limit. • This feature is disabled if the following inputs are activated. • OPEN, SAFETY, SHADOW, CLS-EDGE or STOP. 18
Page 1 and 2: OWNER’S MANUAL GP-SW100 Commercia
Page 3 and 4: Table of Contents Gate Operator Cla
Page 5 and 6: Important Safety Instructions Impor
Page 7 and 8: Important Safety Instructions Impor
Page 9 and 10: Important Safety Instructions Warni
Page 11 and 12: Parts Identification Fully Assemble
Page 13 and 14: Using the Mounting Template The mou
Page 15 and 16: Removing the Operator Housing Befor
Page 17 and 18: Gate Arm Connection Overview Right
Page 19: Control Board Description COM +12V
Page 23 and 24: LINK COM Input Connections NOTE:
Page 25 and 26: Output Connections LOCK N.C. LOCK C
Page 27 and 28: Prison Mode Operation (CLASS IV APP
Page 29 and 30: Installing a Dual Gate Operator Sys
Page 31 and 32: Overview of a Dual Gate Operator In
Page 33 and 34: TroubleShooting Guide GP-SW100 Audi
Page 35 and 36: Symptom Diagnosis Check Close Edge
Page 37: Installation Checklist The installa

GTO/PRO GP-SW100 - Gate Openers | Access Controls

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?