sliding patio door - Truth Hardware

More documents

Recommendations

Info

MISCELLANEOUS HARDWARE 45 JAMB JACKS 15 Now you can install and adjust doors & windows quicker and easier than ever before. Truth’s Jamb Jacks are a specially designed fastening system for mounting door & window frames into rough openings. Jamb Jacks replace the shims used to square the window or door in the rough opening. FASTER INSTALLATION: Using the unique adjustable “screws” (Jamb Jacks) a single unit can be installed without shims in just minutes. SIMPLE ADJUSTMENT: Jamb Jacks provide quick and precise window and door adjustment at the time of installation and when future problems develop caused by foundation settlement. No more need to tear apart a door or window to reshim it. By simply turning the Jamb Jack screws all necessary adjustments can easily be made while the unit is in place. VERSATILE: Jamb Jacks are available for most wood door and window systems, including residential, light commercial or replacement applications, with wood or masonry openings. MATERIAL: Steel screws. Acetal insert and finishing cap. ORDERING INFORMATION: Jamb Jack II (windows) 1. Order #21170 - Jamb Jack II. See Truth Tip #2. Optional #21146.73 Finishing Cap. (See Truth Tip #3). Jamb Jack III (windows and doors) 1. Order Insert & Screw separately. Door Application (See Truth Tip #2): #21150 Door Insert #21171 Door Screw Window Application #21151 Window Insert #21175 Window Screw 2. Order #21146.73 White Finishing Cap. (See Truth Tip #3). 3. Order #21183 Turbo Driver Installation Bit (power installation of insert). 4. Also available pre-packaged as installer packs for doors or windows - includes: inserts, screws, finishing cap and turbo driver. #11076 Installer Pack (door) Jamb Jack II shown TRUTH TIPS: 1. When installing the Jamb Jack III screw into the frame, make sure that the screw snaps twice into the insert. 2. Truth recommends that six Jamb Jack’s be used in every door application (three per jamb) and four be used in window applications (two per jamb). NOTE: Additional Jamb Jacks may be required for window applications depending upon the size of the unit. 3. White Finishing Cap may be painted to match non-standard colors. 4. T25 Torx Driver is required for installing and adjusting Jamb Jack III Screws. Not available from Truth Hardware. 5. Solid shims are recommended behind the strike plate locations on door jamb installations. 6. Due to the design of both Jamb Jack II and Jamb Jack III, neither system can be removed once they are installed. Care must be used when selecting installation points for any Jamb Jack unit.
45 JAMB JACKS FIG. 1 INSTALLATION OF JAMB JACK II JAMB JACK II 21170 TO INSTALL: TURN JAMB JACK IN CLOCKWISE DIRECTION.(TURNS THE THREADED JAMB SLEEVE AND SCREW TOGETHER) CROSS RECESS SCREW DRIVER (PHILLIPS DRIVE) NOT AVAILABLE FROM TRUTH Ø9/64 PILOT HOLE FRAME JAMB Ø.500 X .250 DEEP Ø.250 PILOT HOLE FFIG. 22 ADJUSTMENT OF OF JAMB JAMB JACK JACK II II TO ADJUST: TURN CLOCKWISE-PUSHES JAMB IN TURN COUNTER CLOCKWISE-PULLS JAMB OUT CROSS RECESS SCREW DRIVER (PHILLIPS DRIVE) NOT AVAILABLE FROM THRUTH FRAME JAMB JAMB JACK II 21170 FFIG. 33 INSTALLATION INSTALLATION OF OF JAM JAMB JACK JACK III WINDOW III WINDOW INSERT INSERT TURBO DRIVER 21183 WINDOW INSERT 21151 INSERT TO BE FLUSH WITH JAMB TURN INSERT CLOCKWISE TO INSTALL INTO JAMB FRAME SIDE OF JAMB JAMB PILOT HOLE 13.5 mm (.531 in. APPROX.) DRILL 15a
Page 2 and 3:
patio doorhardware catalog handlese
Page 4 and 5:
ROLLERS FOR PATIODOORS SIDE ADJUST
Page 6 and 7:
SIDE ADJUST TANDEM ROLLERS F FIG.1A
Page 8 and 9:
SIDE ADJUST TANDEM ROLLERS FIG.338.
Page 10 and 11:
ROLLERS FOR PATIO DOORS END ADJUST
Page 12 and 13:
END ADJUST TANDEM ROLLERS FIG. 1 19
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
END ADJUST TANDEM ROLLERS FIG. F 8
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
END ADJUST TANDEM ROLLERS FIG. 22 S
Page 32 and 33:
ROLLERS FOR PATIO DOORS 1910 SINGLE
Page 34 and 35:
ROLLERS FOR SCREENDOORS sCREEN ROLL
Page 36 and 37:
sCREEN ROLLERs FIG.3500SERIES F COR
Page 38 and 39:
sCREEN ROLLERs FIG.64518-1000 SCREE
Page 40 and 41:
HANDLES & LOCKSETS MORTISE LOCK APP
Page 42 and 43:
SIGNATURE SERIES PATIO DOOR HANDLE
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
ALLURE SERIES PATIO DOOR HANDLE SET
Page 56 and 57:
ALLURE SERIES PATIO DOOR HANDLE SET
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
2995 PATIO DOOR HANDLE SETS FIG. 2
Page 64 and 65:
Page 66 and 67:
2939/2940/2949 OUTSIDE PULLS 10b FI
Page 68 and 69: HANDLES & LOCKSETS MORTISE LOCK APP
Page 70 and 71: 2300/2320 MORTISE LOCKS AND HANDLES
Page 74 and 75: P 2300/2320 MORTISE LOCKS AND HANDL
Page 80 and 81: NEXUS TWO-POINT MORTISE LOCK FIG. 2
Page 90 and 91: NEXUS THREE-POINT MORTISE LOCK FIG.
Page 108 and 109: TWO-POINT MORTISE LOCK FIG. 2 32608
Page 114 and 115: MISCELLANEOUS PATIO DOOR HARDWARE 4
Page 116 and 117: 41 SECONDARY PATIO DOOR LIMITER FIG
Page 120 and 121: 45 JAMB JACKS 15b ADJUSTMENT OF JAM
Page 122 and 123: .728 (18.5mm) 45 JAMB JACKS 15d JAM
Page 124 and 125: SWING PATIO DOORS SENTRY MULTI-POIN
Page 126 and 127: SENTRY MULTI-POINT HINGED PATIO DOO
Page 169 and 170:
SENTRY MULTI-POINT HINGED PATIO DOO
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
SENTRY ADJUSTABLE HINGES FIG. 1 SEN
Page 201 and 202:
SENTRY ADJUSTABLE HINGES FIG. 3 SEN
Page 203 and 204:
SENTRY ADJUSTABLE HINGES 18e 700 WE
Page 205 and 206:
SWING PATIO DOORS 15 SENTRY® MULTI
Page 207 and 208:
SENTRY® MULTI-POINT LOCKING HARDWA
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
show all

sliding patio door - Truth Hardware

Create successful ePaper yourself

Delete template?

Save as template?