sliding patio door - Truth Hardware

More documents

Recommendations

Info

HANDLES & LOCKSETS MORTISE LOCK APPLICATIONS 2939/2940/2949 OUTSIDE PULLS 10 • Truth Hardware’s economically priced #2939, #2940 & #2949 series are projecting exterior patio door pulls that, as an option, can house a key lock cylinder for outside key lock operation. • The #2939 and #2949 Series Exterior Pulls are designed to be used only with mortise lock handle designs. • The #2949 series is smoothly contoured for a contemporary European look. • The traditional #2940 Series Exterior Pull is designed primarily to be used with Clam and Insert-type handles, such as Truth’s #2041 Series and #40.63/64 Series interior surfacemounted handle and lock sets. The #2940 Series can also accommodate some mortise lock handles. • When a key lock is required, the cylinder hole plug may be removed (pushed out or drilled) in the field by the installer for retrofitting, or removal may be factory specified. Anti-knock-out plugs are available for added security when pulls are mounted without lock cylinders. • On #2940 series pulls, when a key lock is installed, only a portion of the cylinder length is enclosed. Approximately .28" of the cylinder projects from the back, to be inserted into a .593" diameter hole in the stile. • Conversely, the 1.33" height of the #2939 and #2949 series pulls permit the complete enclosure of the key lock cylinder, when the key lock option is chosen. • On the backside of the #2940 series are four tapped screw holes. The orientation of these two pairs of mounting holes will correspond to the various interior handle screw holes and secure the pull to the stile. • #2940 series low profile outside pull is used primarily on aluminum door applications with insert or clam latch style interior handles. • On the backside of the #2939 and #2949 series are six tapped screw holes, two of which secure the pull to the stile. The six holes translate into three pairs of holes on 3.937" centers. These holes allow for vertical alignment of the pull with the screws when installed with a lock cylinder. • Two anti-slide gaskets are supplied with each pull to keep pull stationary on stile. MATERIAL & FINISHES: Available in zinc die cast and painted. Paint Finishes are electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth’s Color Chart for examples of Truth’s most popular finish options. WARRANTY: Protected under the terms of the Truth Warranty for Window and Door Manufactures and Authorized Distributors. Refer to Truth’s Terms & Conditions for further details. ORDERING INFORMATION: 1. Order item number corresponding to desired Outside Pull. 2. Specify finish. 3. Specify fasteners (sold separately). Note: Please identify thickness of door pane to determine screw length required. 4. To determine blade length for key lock cylinder refer to Fig. 5. TRUTH TIPS: 1. A Truth Hardware Secondary Patio Door Lock or Limiter can be added for applications requiring additional security. 2. Bumper guards (Truth item number 22082.XX), to keep door sash from contacting the opposite jamb during its travel, are highly recommended (see Handleset Accessories section). 3. The use of frame adjusters (Jamb Jacks) is recommended for easy correction of out of square or racked door installations. Frame adjustment can improve both weather seal tightness and door operation over the life of the door.
2939/2940/2949 OUTSIDE PULLS FIG. 1 2939 SERIES OUTSIDE PULL 2939 SERIES ITEM NUMBERS 32479.XX WITH KEY CYLINDER HOLE 32442.XX WITHOUT CYLINDER KEY HOLE 7.365 [187.1 mm] 1.115 [28.3 mm] NOTES: 1. HANDLE IS TAPPED TO ACCEPT 8-32 MOUNTING SCREWS. 2. TO DETERMINE MOUNTING SCREW LENGTH, SEE NOTES FOR CORESPONDING INSIDE HANDLE 1.032 [26.2 mm] AVAILABLE INSIDE PULLS 2995 2889 2994 2992 2761 2235 2237 2750 FIG. 2 2940 SERIES OUTSIDE PULL 2940 SERIES ITEM NUMBERS 32437.XX WITH KEY HOLE CYLINDER 32328.XX WITHOUT KEY HOLE CYLINDER 7.365 [187.1 mm] 1.115 [28.3 mm] 1.032 [26.2 mm] NOTES: 1. HANDLE IS TAPPED TO ACCEPT 8-32 MOUNTING SCREWS. 2. TO DETERMINE MOUNTING SCREW LENGTH, SEE NOTES FOR CORRESPONDING INSIDE HANDLE AVAILABLE INSIDE PULLS 40.63 40.64 2041 10a
Page 2 and 3:
patio doorhardware catalog handlese
Page 4 and 5:
ROLLERS FOR PATIODOORS SIDE ADJUST
Page 6 and 7:
SIDE ADJUST TANDEM ROLLERS F FIG.1A
Page 8 and 9:
SIDE ADJUST TANDEM ROLLERS FIG.338.
Page 10 and 11:
ROLLERS FOR PATIO DOORS END ADJUST
Page 12 and 13:
END ADJUST TANDEM ROLLERS FIG. 1 19
Page 14 and 15: END ADJUST TANDEM ROLLERS FIG. 4 19
Page 18 and 19: END ADJUST TANDEM ROLLERS FIG. F 8
Page 30 and 31: END ADJUST TANDEM ROLLERS FIG. 22 S
Page 32 and 33: ROLLERS FOR PATIO DOORS 1910 SINGLE
Page 34 and 35: ROLLERS FOR SCREENDOORS sCREEN ROLL
Page 36 and 37: sCREEN ROLLERs FIG.3500SERIES F COR
Page 38 and 39: sCREEN ROLLERs FIG.64518-1000 SCREE
Page 40 and 41: HANDLES & LOCKSETS MORTISE LOCK APP
Page 42 and 43: SIGNATURE SERIES PATIO DOOR HANDLE
Page 54 and 55: ALLURE SERIES PATIO DOOR HANDLE SET
Page 56 and 57: ALLURE SERIES PATIO DOOR HANDLE SET
Page 62 and 63: 2995 PATIO DOOR HANDLE SETS FIG. 2
Page 66 and 67: 2939/2940/2949 OUTSIDE PULLS 10b FI
Page 70 and 71: 2300/2320 MORTISE LOCKS AND HANDLES
Page 74 and 75: P 2300/2320 MORTISE LOCKS AND HANDL
Page 80 and 81: NEXUS TWO-POINT MORTISE LOCK FIG. 2
Page 90 and 91: NEXUS THREE-POINT MORTISE LOCK FIG.
Page 108 and 109: TWO-POINT MORTISE LOCK FIG. 2 32608
Page 114 and 115:
MISCELLANEOUS PATIO DOOR HARDWARE 4
Page 116 and 117:
41 SECONDARY PATIO DOOR LIMITER FIG
Page 118 and 119:
MISCELLANEOUS HARDWARE 45 JAMB JACK
Page 120 and 121:
45 JAMB JACKS 15b ADJUSTMENT OF JAM
Page 122 and 123:
.728 (18.5mm) 45 JAMB JACKS 15d JAM
Page 124 and 125:
SWING PATIO DOORS SENTRY MULTI-POIN
Page 126 and 127:
SENTRY MULTI-POINT HINGED PATIO DOO
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
SENTRY ADJUSTABLE HINGES FIG. 1 SEN
Page 201 and 202:
SENTRY ADJUSTABLE HINGES FIG. 3 SEN
Page 203 and 204:
SENTRY ADJUSTABLE HINGES 18e 700 WE
Page 205 and 206:
SWING PATIO DOORS 15 SENTRY® MULTI
Page 207 and 208:
SENTRY® MULTI-POINT LOCKING HARDWA
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
show all

sliding patio door - Truth Hardware

Create successful ePaper yourself

Delete template?

Save as template?