download - Ilme

More documents

Recommendations

Info

i Insulating enclosures “T-Type” series Alongside the wide range of traditional metal enclosures for ILME multipole connectors, there is now available a new series of enclosures in self-extinguishing thermoplastic material in the most common sizes of “44.27”, “57.27”, “77.27” and “104.27”. Quality and low cost are the main features of these enclosures, as an outcome of careful product studies. Valuable characteristics of these new enclosures: - structurally solid and mechanically robust, due to their increased thickness; - resistance to the main chemical agents, found in industrial environments (see tab. page 3); - pre-fastened gaskets for easier installation; - external dimensions of the bulkhead-mount housings are similar to those of the corresponding metal housings; hole fixing centres are unchanged; - wide space inside enclosures for cables, with mounted connectors, similar to their corresponding metal version high construction enclosures; - the possibility with their use to create total insulation constructions (equivalent to class II) b; - the surface mounting, high construction housings are supplied with an open threaded entry and diametrically opposite a closed threaded entry, which can be opened by the user, if required (with suitable tool); - absence of powder paint for environments in which these are not recommended; - non-electrostatic thermoplastic material. - manufactured from insulating material, they do not require a special reinforced insulation as metal ones do, for use with series CME higher voltage connector inserts (screw-type terminals); - degree of protection for coupled connectors is IP65 according to norm IEC/EN 60529; - UL Type 12 (= NEMA 12) degree of protection according to American standards ANSI/UL 50 and UL 50E for indoor use; - each enclosure carries its own part number and conformity markings; - ambient temperature limits -40 °C / +90 °C. T - TYPE • bulkhead housings; • surface mounting housings (with one open threaded entry and one closed entry); • single lever, side and top entry, for size (“44.27”); • cover (for housings and hoods with levers); • side entry hood; • top entry hood; • double lever for other sizes (“57.27, 77.27, 104.27”) All used materials conform with the RoHS 2002/95/EC Directive and all further modifications. For technical data-sheet and further information please look at our technical catalogues on website www.ilme.com 63
i NEW Insulating enclosures T-TYPE with single lever • housings and lever in thermoplastic material self-extinguishing • the enclosures ensure IP65 protection rating when mated and locked with the closing levers (in compliance with EN 60529) to be completed with cable glands • pre-fastened gasket • UL Type 12 (Nema 12) degree of protection according to ANSI/UL 50 ILME description packaging part No. bulkhead mounting housings for inserts single locking device - IP65 (EN 60529) to be coupled with: TMAO L, CHO L, CAO L, TMAV L, CHV L, CAV L hoods and TCHC L covers for JCNE, JCSE, CSH, CNE, CCE, CSE, CSS, CTSE, CT, CDD, CQE, MIXO inserts TCHI 06 L size 44.27 40 NEW surface mounting housings for inserts single locking device - IP65 (EN 60529) to be coupled with: TMAO L, CHO L, CAO L, TMAV L, CHV L, CAV L hoods and TCHC L covers for JCNE, JCSE, CSH, CNE, CCE, CSE, CDD, CQE, MIXO inserts TMAP 06 L25 size 44.27 - threading M25 20 TMAP 06 L32 size 44.27 - threading M32 20 NEW hoods for inserts side entry - IP65 (EN 60529) to be coupled with: TCHI L, C7I L, JCVI L mounting housings and TMAP L, C7P L, JCVP L for JCNE, JCSE, CSH, CNE, CCE, CSE, CDD, CQE, MIXO inserts T - TYPE TMAO 06 L25 size 44.27 - threading M25 20 TMAO 06 L32 size 44.27 - threading M32 20 NEW hoods for inserts top entry - IP65 (EN 60529) to be coupled with: TCHI L, C7I L, JCVI L mounting housings and TMAP L, C7P L, JCVP L for JCNE, JCSE, CSH, CNE, CCE, CSE, CDD, CQE, MIXO inserts TMAV 06 L25 size 44.27 - threading M25 20 TMAV 06 L32 size 44.27 - threading M32 20 NEW protection covers with pegs without gasket - IP65 (EN 60529) to be coupled with: TCHI L, CHI L, C7I L, JCVI L mounting housings and TMAP L, CHP L, C7P L, JCVP L TCHC 06 L size 44.27 5 Interchangeability with other ILME series TCH series housings can be coupled with metal hoods; insulating hoods can be coupled with “V-Type” metal housings. The hood “57.27”, “77.27” and “104.27” can be mounted on COB TCQ and COB BC frames simply by replacing the supplied levers with COB L levers (to be purchased in addition). Insulating enclosures are ideal for mounting of all ILME inserts with the exception of series models CT 40/ 64 and CTS 40/ 64 connector. Inserts with 45° terminals of the CT series (screw-type terminals) and CTSE (spring terminals) are only insertable from the front (therefore not from the back) of the bulkhead housing. Being made by insulating material, they do not require a special reinforced insulation as metal ones do, for use with series CME higher voltage connector inserts (screw-type terminals). With the exception of the limitations described below, it is generally possible to mount the MIXO series modular connectors and frames with the ground and screen anchors dedicated to this series. Limitations With respect to enclosures in metal alloy, ILME insulating enclosures have some limitations of use in combination with particular accessories: • CRZ 06/ 10/ 16/ 24 reduction plates cannot be mounted with TCHI bulkhead housings due to increased dimensions of the fastening flange of these enclosures. • The CYG 16 in-line joint cannot be mounted on the TCHI 16 bulkhead housing because the gaskets of the latter do not fit together with the joint profile. • The CYR 16.3 and CYR 24.4 round cable feed-throughs are difficult to position on their respective TCHI 16 and TCHI 24 bulkhead housings. • CPT 24 disposable protection cover cannot be mounted on enclosures due to increased outer dimensions of these enclosures. • MIXO series insert anchors cannot be mounted on TMAO 06/ 10 enclosures. • CN insert anchors cannot be mounted on TMAO 06/ 10 enclosures. • When using both cable entries of surface mounting housings, the conduit shall be of insulating type. For technical data-sheet and further information please look at our technical catalogues on website www.ilme.com 64
Page 1 and 2:
CSH-SQUICH connection without tools
Page 3 and 4:
V-TYPE IP67 i
Page 5 and 6:
C - TYPE CLASSIC LEVER V - TYPE IP6
Page 7 and 8:
Summary JCNE 6 - 10 - 16 - 24 - (32
Page 9 and 10:
Summary C - TYPE V - TYPE T-TYPE IN
Page 11 and 12:
Summary A - CR CABLE GLAND A - CR C
Page 13 and 14: i NEW bridges page 33 MIXO 17 poles
Page 15 and 16: i feature of inserts for multipole
Page 17 and 18: i enclosures and inserts combinatio
Page 19 and 20: eliable economical • inserts in l
Page 21 and 22: CSH SQUICH connections without tool
Page 23 and 24: i inserts for multipole connectors
Page 27 and 28: C - TYPE MIXO INSERTS i inserts for
Page 31 and 32: CKS spring terminal connections 400
Page 37 and 38: i inserts for multipole connectos C
Page 41 and 42: i modular inserts MIXO • to be mo
Page 43 and 44: i modular inserts MIXO • inserts
Page 45 and 46: i modular inserts MIXO • inserts
Page 47 and 48: i modular inserts MIXO • USB conn
Page 49 and 50: i modular inserts MIXO for contacts
Page 51 and 52: i modular inserts MIXO drawing ILME
Page 53 and 54: i modular inserts MIXO drawing ILME
Page 55 and 56: i accessories for inserts drawing I
Page 57 and 58: i accessories for inserts drawing I
Page 59 and 60: i crimping tools for connectors ins
Page 61 and 62: T - TYPE JEI page 64 page 67 V - TY
Page 63: T-Type Insulating enclosures
Page 67 and 68: elia le e ono i al • inserts in l
Page 69 and 70: i bulkhead and surface mounting hou
Page 71 and 72: V-Type IP67
Page 73 and 74: i bulkhead and surface mounting hou
Page 75 and 76: i metal enclosures for inserts sing
Page 77 and 78: i insulating enclosures for inserts
Page 79 and 80: i bulkhead mounting housings for in
Page 81 and 82: i high surface mounting housings fo
Page 83 and 84: i high surface mounting housings fo
Page 85 and 86: i hoods for single locking lever
Page 87 and 88: i bulkhead mounting housings and ho
Page 89 and 90: CHO CAO CAV 2 i bulkhead and surfac
Page 91 and 92: i hoods for double lever • the en
Page 93 and 94: i hoods for double lever • the en
Page 95 and 96: i bulkhead mounting housings for do
Page 97 and 98: i surface mounting housings for dou
Page 99 and 100: i hoods with double lever • enclo
Page 101 and 102: i hoods for ribbon cable double lev
Page 103 and 104: i complete connectors 16A max - 500
Page 105 and 106: CSEF... CSEM... CHO... CHV... i com
Page 107 and 108: i COB panel supports for connector
Page 109 and 110: i accessories for connectors drawin
Page 111 and 112: i special execution enclosures CYG
Page 113 and 114: i enclosures high protection IP68 v
Page 115 and 116:
i ILME description packaging part N
Page 117 and 118:
i CH-CA and MA enclosures for speci
Page 119 and 120:
i EMC enclosures for special applic
Page 121 and 122:
i RJ45 connectors mounted in enclos
Page 123 and 124:
i A - CR cable gland drawing ILME d
Page 125 and 126:
i A - CR cable gland drawing ILME d
Page 127 and 128:
i AI fittings and flexible tubes
Page 129 and 130:
APV authentic and renewed
Page 131 and 132:
i AP containing boxes drawing ILME
Page 133 and 134:
i AC boxes for control devices and
Page 135 and 136:
i AC boxes for control devices and
Page 137 and 138:
i Z load-break switches for industr
Page 139 and 140:
i Part Nos. index Part No. page Par
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
i Part Nos. index Part No. page ZR
Page 153 and 154:
i Notes
Page 155 and 156:
i Notes
Page 157:
i Sale organization Head office I.L
show all

download - Ilme

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?