User manual ArcPower Micro 270 - Anolis

More documents

Recommendations

Info

7.ArcPower Micro 270 - DMX protocolversion 2.0 (software version 1.3 and higher)Mode/Channel Value Function1 21 12 23 34560-2550-2550-2550-78-1516-2324-3940-4748-5556-6869-7172-7980-8788-9596-103104-111112-119120-127128-135136-143142-151152-159160-167168-175176-183184-191192-199200-207208-215216-223224-231232-239240-247248-2550-3132-6364-9596-127128-143144-159160-191192-223224-2550-255RED LEDRed LED saturation control (0-100%)GREEN LEDGreen LED saturation control (0-100%)BLUE LEDBlue LED saturation control (0-100%)MACRO SELECTIONNo functionMacro 1Macro 2Macro 3Macro 4Macro 5Macro 6Macro 7Macro 8Macro 9Macro 10Macro 11Macro 12Macro 13Macro 14Macro 15Macro 16Macro 17Macro 18Macro 19Macro 20Macro 21Macro 22Macro 23Macro 24Macro 25Macro 26Macro 27Macro 28Macro 29Rainbow effect with variable speedSHUTTER/STROBEShutter closedShutter openStrobe-effect from slow to fastShutter openOpening pulses in sequences slow--> fastClosing pulses in sequences fast --> slowShutter openRandom strobe-effects from slow to fastShutter openDIMMERDimmer intensity from 0% to 100%Typeof controlproportionalproportionalproportionalstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepstepproportionalstepstepproportionalstepproportionalproportionalstepproportionalstepproportional10
8.Control boardThe control panel situated on the top cover of the ArcPower Micro 270 allows DMX addressing,calling built-inprograms and setting the fixture behaviourControl elements:[ENTER] button- enters menu,confirms adjusted values and leaves menu., [UP] button and[DOWN] button- moves between menu items on the the same level, sets values.In order to leave the menu without saving value,press [UP] and [DOWN ] at the same time.After switching on the ArcPower Micro 270 ,the display shows the initial DMX address:Use [UP],[DOWN] to browse through the menu.In order to to select a function or submenu,press [ENTER].8.1 Addressing the ArcPower Micro 270The fixture can be operated in the two modes:DMX mode-fixture is controlled via DMX 512 by an externalDMX controllerStand-alone mode - fixture uses Built-in programs and isable to control other fixtures in the master/slave chain.See the chapter "Stand-alone mode" for detail description.For DMX mode, it is important to define the starting DMX address from which the ArcPower 36 will respond tothe DMX controllerSetting the DMX start channel for DMX operating:1. Connect ArcPower Micro 270 to the mains.2. Browse through the menu by pressing the [UP] and [DOWN] buttons until the display shows current addres"001".Confirm by pressing [ENTER] button and "001" will start to flash frequently.3. Use the [UP] and [Down] buttons to select the desired address.4. Confirm by pressing [ENTER].After having addressed ArcPower Micro 270, you may now start operating ArcPower Micro 270 via your DMXcontroller.8.2 Program runningBy entering this menu a complete overview of all programs is offered,from which the program to be run canbe selected, by pressing [ENTER].Selected program runs in a loop.The fixture includes 10 built-in programs(P.01-P.10) and 3 free editable programs (E.P.1-E.P.3),each up to 50 steps.If Item "AUt" is On,the fixture in DMX mode will remember last running program and this program will run afterswitching on the fixture.Each program step has a fade time-the time during which effects go to the current step and a Standing time--the time,during which effects last in the current step.11
Page 1 and 2: version 1.7
Page 3 and 4: CAUTION!Unplug mains lead before op
Page 5 and 6: This device falls under protection
Page 7 and 8: Multiple ArcPower Micro 270 install
Page 9: 6.ArcPower Micro 270 - Control menu
Page 13 and 14: 8.4 Test sequencesUse the item to r
Page 15 and 16: 9.Technical Specifications:Power su

User manual ArcPower Micro 270 - Anolis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?