80960KA EMBEDDED 32-BIT MICROPROCESSOR - Datasheet ...

More documents

Recommendations

Info

80960KA2.6. Absolute Maximum Ratings NOTICE: This is a production data sheet. The specificationsare subject to change without notice.Operating Temperature (PGA).............. 0°C to +85°C Case(PQFP) ......... 0°C to +100°C CaseStorage Temperature ................................. –65°C to +150°CVoltage on Any Pin................................. –0.5V to V CC +0.5VPower Dissipation .......................................... 2.5W (25 MHz)2.7. DC CharacteristicsPGA: 80960KA (16 MHz) T CASE = 0°C to +85°C, V CC = 5V ± 10%80960KA (20 and 25 MHz) T CASE = 0°C to +85°C, V CC = 5V ± 5%PQFP: 80960KA (16 MHz) T CASE = 0°C to +100°C, V CC = 5V ± 10%80960KA (20 and 25 MHz) T CASE = 0°C to +100°C, V CC = 5V ± 5%*WARNING: Stressing the device beyond the “Absolute MaximumRatings” may cause permanent damage. These arestress ratings only. Operation beyond the “Operating Conditions”is not recommended and extended exposure beyond the“Operating Conditions” may affect device reliability.Table 5. DC CharacteristicsSymbol Parameter Min Max Units NotesV IL Input Low Voltage –0.3 +0.8 VV IH Input High Voltage 2.0 V CC + 0.3 VV CL CLK2 Input Low Voltage –0.3 +0.8 VV CH CLK2 Input High Voltage 0.55 V CC V CC + 0.3 VV OL Output Low Voltage 0.45 V (1,2)V OH Output High Voltage 2.4 V (3,4)I CCPower Supply Current:16 MHz20 MHz25 MHzI LI Input Leakage Current ±15 µA 0 ≤ V IN ≤ V CCI LO Output Leakage Current ±15 µA 0.45 ≤ V O ≤ V CCC IN Input Capacitance 10 pF f C = 1 MHz (6)C O Output Capacitance 12 pF f C = 1 MHz (6)C CLK Clock Capacitance 10 pF f C = 1 MHz (6)NOTES:1. For three-state outputs, this parameter is measured at:Address/Data............................................................................................................................................................................................. 4.0 mAControls ...................................................................................................................................................................................................... 5.0 mA2. For open-drain outputs ................................................................................................................................................................................ 25 mA3. This parameter is measured at:Address/Data ........................................................................................................................................................................................... -1.0 mAControls .................................................................................................................................................................................................... -0.9 mAALE .......................................................................................................................................................................................................... -5.0 mA4. Not measured on open-drain outputs.5. Measured at worst case frequency, V CC and temperature, with device operating and outputs loaded to the test conditions in Figures 12 and 13.Figure 7, Figure 8 and Figure 9 indicate typical values.6. Input, output and clock capacitance are not tested.15315360420mAmAmA(5)(5)(5)
80960KA2.8. AC SpecificationsThis section describes the AC specifications for the80960KA pins. All input and output timings arespecified relative to the 1.5 V level of the rising edgeof CLK2. For output timings the specifications refer tothe time it takes the signal to reach 1.5 V.For input timings the specifications refer to the time atwhich the signal reaches (for input setup) or leaves(for hold time) the TTL levels of LOW (0.8 V) or HIGH(2.0 V). All AC testing should be done with inputvoltages of 0.4 V and 2.4 V, except for the clock(CLK2), which should be tested with input voltages of0.45 V and 0.55 V CC .EDGEA B C D A B CCLK21.5V 1.5V 1.5V 1.5V0.8VT 61.5V 1.5VOUTPUTS:LAD 31:0ADSW/R, DENBE3:0HLDACACHELOCK, INTAT 91.5V VALID OUTPUT 1.5VT 8T 8T 13 T 14ALET 7T 6T 9DT/R1.5V VALID OUTPUT 1.5VINPUTS:LAD31:0BADACIAC/INT0, INT1INT2/INTR, INT3HOLDLOCKREADYT 10 T 112.0V 2.0V0.8V 0.8VT 12 T 112.0V 2.0V0.8V 0.8VVALID INPUTFigure 14. Drive Levels and Timing Relationships for 80960KA Signals16
Page 3 and 4: CONTENTSFigure 24.Figure 25.Figure
Page 6 and 7: 80960KATable 1. 80960KA Instruction
Page 8 and 9: 80960KApurpose registers provided i
Page 10 and 11: 80960KAdebug instruction. In each c
Page 12 and 13: 80960KABE3:0OO.D.BYTE ENABLE LINES
Page 14 and 15: 80960KA2.3. Connection Recommendati
Page 16 and 17: 80960KATEMP = +22°C@5.5V@5.0V@4.5V
Page 20 and 21: 80960KA2.8.1. AC Specification Tabl
Page 22 and 23: 80960KA1. Clock rise and fall times
Page 24 and 25: 80960KA3.0 MECHANICAL DATA3.1. Pack
Page 26 and 27: 80960KA14 13 12 11 10 9 8 7 6 5 4 3
Page 28 and 29: 80960KA3.2. PinoutTable 9. 80960KA
Page 30 and 31: 80960KATable 11. 80960KA PQFP Pinou
Page 32 and 33: 80960KA3.3. Package Thermal Specifi
Page 34 and 35: 80960KATEMPERATURE ( o C)9085807570
Page 36 and 37: 80960KA4.0 WAVEFORMSFigures 27, 28,
Page 38 and 39: 80960KAT a T w T w T d T w T d T w
Page 40 and 41: 80960KAPREVIOUSCYCLEINTERRUPTACKNOW
Page 42 and 43: 80960KA39

80960KA EMBEDDED 32-BIT MICROPROCESSOR - Datasheet ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?