Download - E-THERM as

More documents

Recommendations

Info

Installation2. INSTALLATION2.1. SAFETY DURING INSTALLATION (MOUNTING AND WIRING)Danger !• Q7000 must be installed and wired by qualified staff authorised to work on low voltageindustrial electrical facilities.• Load connectors must stay plugged-in, even if they are not used.• Units must be installed in a fan-cooled cabinet, to ensure that condensation and pollution are excluded.We recommend fitting fan-cooled cabinets with a fan failure detection device or a thermal safety cut-out.The cabinet must be closed and connected to the protective earth according to IEC 364 orapplicable national standards.• Units must be mounted with no obstructions above or below the unit which could reduce or hamper air flow.If several units are fitted in the same cabinet, arrange them such that air from one unit is not drawnin by the unit above. Leave a gap of at least 10 mm between two adjacent units.!Warning !• Nominal currents correspond to use at ambient temperatures.Overheating may cause incorrect operation and may even lead to components being damaged.Danger !• It is the user’s responsibility to wire and protect the facility according to best practice and applicable standards.A suitable device, ensuring that the unit can be electrically isolated from the supply, must beinstalled upline to enable work to be performed safely. Conductor cross-sections should comply withIEC 943. Use only copper cables and wires designed for use at up to 75°C.• Before connecting or disconnecting the unit check that power and control cables and leads areisolated from voltage sources. The protective earth must be connected before any otherconnections are made and should be the last cable to be disconnected.The protective earth connection terminal is marked with the symbol.In order to ensure the electrical security and the protective earth continuity,all the front panel screws must be clamped at the right clamping torque (0.5 Nm).!Warning !• To ensure that Q7000 comply with Electromagnetic Compatibility requirements, ensure that thepanel to which they are attached is correctly grounded.The ground connection, designed toensure ground continuity, is not in any way a substitute for the protective earth connection.To ensure the protective earth continuity and the electrical safety of the installation, all thefront panel screws must be clamped correctly, at the clamping torque indicated.Q7000 User Manaual2-2
Installation2.2. WIRING DRIVER CONNECTION DIAGRAMQ7000/- T° / DisableGRF / DLFONNetwork StatusModele StatusTxRxRJ 11 configuration connector (iTools) -ModBus protocol only.DB9 connector compatible with ‘FastConnect’ ProfiBus connector type.Digital communication wiring -RS 485 for ModBus & ProfibusprotocolsNote :Wiring for DevicNet protocolcomplies with the actualdirectives used.iTools919293949512345678COM. UserSpeed & AddressDNV-CAN_LShieldCAN_HV+MOP / PFPBAGND5VPBTB919293949596ENA 640VD 61FAN 600VD 618DVNV-CAN_LShieldCAN_HV+NCMOP / PFPBAGND5VPBTBBTAInhibition digital input -Conduction stoppedPressure sensor digital inputCommunicationbuspolarisation, onthe last deviceof the bus96NCBTAENA 640VD 61FAN 600VD 61Digitalinput1a 711b 72Alarm relay 1 output1a1b2a717273OutputRelays2a 812b 82Alarm relay 1 output2b 747Vaux 150V 18AuxEN 60947-4-37Vaux150V 18NCElectronic external power supply(auxiliary supply) 24 V, 115 V or 230 V,according to code.The connector 18 must be connectedto the external supply neutral or onthe second phase (if supply with twophases).Q7000 User Manaual2-3
Page 1 and 2: MultichannelThyristor Power UnitENG
Page 3 and 4: European Directives ans applicable
Page 5 and 6: 1.1. DRIVER CARD DESCRIPTIONIdentif
Page 7 and 8: Identification1.3. TECHNICAL SPECIF
Page 9 and 10: Identification1.4.4. Alarm RelaysTw
Page 11: InstallationCHAPTER 22. INSTALLATIO
Page 15 and 16: Firing ModesCHAPTER 33. FIRING MODE
Page 17 and 18: Firing Modes3.3. INTELLIGENT HALF-C
Page 19 and 20: 4. ALARMSAlarms4.1. SAFETY MECHANIS
Page 21 and 22: Digital CommunicationCHAPITRE 55. D
Page 23 and 24: 5.3. PROFIBUS-DP ProtocolDigital Co
Page 25 and 26: 5.3. DIGITAL COMMUNICATION LEDsDigi
Page 27 and 28: Digital CommunicationGeneral Status
Page 29 and 30: Digital CommunicationChannel Status
Page 31 and 32: 6. COMMISSIONING AND MAINTENANCEMai
Page 33: EUROTHERM WORLDWIDE SALES AND SERVI

Download - E-THERM as

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?