Download - E-THERM as

More documents

Recommendations

Info

MaintenanceCHAPTER 66. COMMISSIONING AND MAINTENANCEContentsPage6.1. Safety during commissioning and maintenance 6-26.1.1. Commissioning - checking the characteristics6.1.2. Commissioning - checking the wiring6.2. Power up6.3. Maintenance7. Eurotherm 7-1Q7000 User Manual6-1
6. COMMISSIONING AND MAINTENANCEMaintenancePle<strong>as</strong>e read carefully before commissioning the unit6.1. SAFETY DURING COMMISSIONING AND MAINTENANCEWarning!• Eurotherm shall not be held responsible for any damage, injury, losses or expenses incurred by!inappropriate use of the product or failure to comply with this manual.• Accordingly the user is responsible for checking, before commissioning the unit, that all thenominal characteristics correspond to the conditions under which it is to be installed and used.Danger!• The product must be commissioned and maintained by qualified personnel, authorised to workin an industrial low voltage environment. Users must not attempt to access internal parts. Theheatsink temperature may exceed 100°C. The heatsink remains hot for approx. 15 minutes afterthe unit is shut down. Avoid touching the heatsink even briefly while the unit is operating.6.1.1. COMMISSIONING - CHECKING THE CHARACTERISTICS!Before powering up the unit, check that the identification code corresponds to the codespecified on the order and that the characteristics are compatible with the facility.Load currentThe maximum load current must be less than or equal to the nominal current value of the solid state contactor,taking account of supply and load variations.Supply voltageThe nominal voltage value must be greater than or equal to the line-to-line or line-to-neutral supply voltage (dependingon the connection scheme).Never use the unit on a supply with a voltage greater than the nominal value +10% <strong>as</strong> this could damage the protection componentsor even the thryistors.Load type (DLF option)For correct operation of the partial load failure detection system, ensures that load type used corresponds to theproduct code (LTCL or SWIR)6.1.2. COMMISSIONING - CHECKING THE WIRINGCut-off and isolation systemsIt is the user’s responsibility to wire and protect the facility according to best practice and applicablestandardsDanger !A suitable device ensuring that the unit can be electrically isolated from the supply must be installedupline to enablework to be performed safely.Protective earth, power and control connectionsBefore checking the wiring, ensure that the power and control wires are isolated from power sources.Check that the protective earth cable is connected to the earth terminal on the unit.Check that the wiring corresponds to the connection diagramCheck the fan power supply (voltage, connections and fuse).Q7000 User Manual6-2
Page 1 and 2: MultichannelThyristor Power UnitENG
Page 3 and 4: European Directives ans applicable
Page 5 and 6: 1.1. DRIVER CARD DESCRIPTIONIdentif
Page 7 and 8: Identification1.3. TECHNICAL SPECIF
Page 9 and 10: Identification1.4.4. Alarm RelaysTw
Page 11 and 12: InstallationCHAPTER 22. INSTALLATIO
Page 13 and 14: Installation2.2. WIRING DRIVER CONN
Page 15 and 16: Firing ModesCHAPTER 33. FIRING MODE
Page 17 and 18: Firing Modes3.3. INTELLIGENT HALF-C
Page 19 and 20: 4. ALARMSAlarms4.1. SAFETY MECHANIS
Page 21 and 22: Digital CommunicationCHAPITRE 55. D
Page 23 and 24: 5.3. PROFIBUS-DP ProtocolDigital Co
Page 25 and 26: 5.3. DIGITAL COMMUNICATION LEDsDigi
Page 27 and 28: Digital CommunicationGeneral Status
Page 29: Digital CommunicationChannel Status
Page 33: EUROTHERM WORLDWIDE SALES AND SERVI

Download - E-THERM as

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?