Aviosys IP Power Switch 9258-PRO Manual - Openxtra

More documents

Recommendations

Info

VC ConfigThe VCT (Voltage & Current ) config allows you to configure the critical points of the Unit Voltage,RMS Current 1, RMS Current 2.When that critical point has been reached the 9258 Pro will respond by sending a e-mailnotification and it safely shut down.Unit Voltage:If the total voltage of the 9258 Pro reaches the critical that has been set the device will safely shutdown.RMS Current 1 (Ports 1-4)The RMS Current 1 is the total number of AMPS that is used for ports 1-4. If the total Ports AMPexceeds the Critical the device will safely shut downRMS Current 2 (Ports 5-8)The RMS Current 2 is the total number of AMPS that is used for ports 5-8. If the total Ports AMPexceeds the Critical the device will safely shut down.VC MonitorThe VCT monitor is the webpage that monitors the status of the VC. It will give you the actualUnit Voltage, RMS Current 1 & RMS Current- 20 –Ref: P9258Y90M02
System ConfigurationSystem SetupThe System Setup page is where you would configure the basic IP information needed for thedevice to work properlyIP Address: The IP Address of the 9258 Pro can be specified here. If you are using a hub orrouter, the IP address may be selected for you already. Otherwise you can manually select the IPAddress here.Subnet Mask: The Subnet Mask Address of the 9258 Pro can be specified here. If you are usinga hub or router, the IP address may be selected for you already. Otherwise you can manuallyselect the IP Address here.Default Gateway: The Default Gateway is given by a router or hub and this is where thatinformation would be specified.DNS: The DNS is the Domain Name Server. This information can be obtained by contacting theISPDHCP Client: The DHCP client allows the 9258 Pro to use DHCP to obtain the IP Informationfrom a Hub or Router.Beeper: The Beeper turns on/off the beeper sound from the 9258 Pro. When commands are senta beep sound will appear.Http Command Verification: The HTTP Verification turns on or off the HTTP Command mode.This mode allows you to send commands directly to the device via internet without having toenter the device.- 21 –Ref: P9258Y90M02
Page 1 and 2: IP Power 9258 ProUser ManualRelease
Page 3 and 4: Table of Content1.) AVIOSYS INTRODU
Page 5 and 6: 1.) Aviosys IntroductionIntroductio
Page 7 and 8: 3.) Hardware Description4 Port Ethe
Page 9 and 10: 4.) Then hit the rescan button on I
Page 11 and 12: 2.) Open IP Edit and any device in
Page 13 and 14: 2.) To setup the device, type in th
Page 16 and 17: RMS Current 2 (Total Current for po
Page 18 and 19: The Control ConsoleThe Right Panel
Page 22 and 23: Device Name: In this section you ca
Page 24 and 25: Schedule Ports 1-4 & Ports 5-8The s
Page 26 and 27: PingThe Auto-ping functionality all
Page 28 and 29: Network WakeupThe network wakeup fu
Page 30 and 31: 9.) Controlling the DeviceCGI HTTP
Page 33 and 34: setfactory+gateway=xxx.xxx.x.xxx+co
Page 35 and 36: Serial Com (RS-232) ControlCom1The
Page 37 and 38: View the examples below for additio
Page 39 and 40: In this example the text is helloCO
Page 41 and 42: Get Current MIB1.3.6.1.4.1.92.59.4.
Page 43: 11.) Frequently Asked Questions (F.

Aviosys IP Power Switch 9258-PRO Manual - Openxtra

Create successful ePaper yourself

Delete template?

Save as template?