FREE POSTER OFFER INSIDE! - Brownells

AR-15/M16
12
HIGH STANDARD CAR-15/M4
MIL-SPEC RECEIVER
EXTENSION TUBE
Replace Factory USGI
Tube Or Convert
Commercial Carbine
To Accept Mil-Spec
Adjustable Buttstock
Replacement receiver extension tube is the correct length
and 1.146" outside diameter for proper fit of a mil-spec carbine
adjustable buttstock. Replace a worn out USGI tube, or convert
a commercial carbine or fixed-stock rifle to accept an adjustable
buttstock that requires the smaller, mil-spec tube. Four,
precision-machined notches on the underside grasp the stock’s
locking pin securely to ensure fast, positive stock length adjustments
without slippage. One-piece aluminum construction with
a tough, abrasion-resistant matte black hardcoat anodized finish.
Rifle conversion also requires a carbine action spring and
buffer, available separately.
SPECS: Aluminum, hardcoat anodized, matte black. 7¼” (18.2cm)
long, 1.146” O.D.
#100-004-252CG Mil-Spec Receiver Extension Tube,
3D43X61 .........................$ 43.61
VLTOR CAR-15/M4
MIL-SPEC RECEIVER EXTENSION
Correct Size For Rattle-Free
Mounting Of Mil-Spec
Collapsible Buttstocks
Receiver extension tube has the correct, 1.146" outside diameter
for mounting collapsible buttstocks designed for the
smaller, mil-spec tube. Lets you mount a mil-spec stock on a
civilian carbine or convert a rifle with A2-style fixed buttstock
to collapsible configuration; carbine action spring and buffer
assembly required. Allows fast, easy repeatability of buttstock
position with five notches on underside to accept the stock’s locking
pin and corresponding white position numbers on top visible
through the witness hole on many stocks. Precision machined
from aluminum bar stock for consistent dimensions that ensure
smooth, snag-free sliding of buttstock.
SPECS: Aluminum, hardcoat anodized, matte black. 7 15 ⁄16" (cm)
long, 1.146” O.D.
#100-003-750CG Mil-Spec Receiver Extension,
3A39X07 .........................$ 39.07
CAA AR-15/M16
4-RAIL HANDGUARD
Extra Mounting Area
For Your Accessories
Four Picatinny rails and rigid
aluminum construction provide a
two-piece handguard capable of
supporting all your accessories,
while holding up to the tough demands of tactical and competition
exercises. Each rail is equipped with removable thermal
rubber covers for better grip and protection for the rails when
not in use. Integral metal heat shields with 24 ventilation holes
help dissipate heat away from the barrel during sustained fire.
Mounts easily using existing delta ring. No gunsmithing required.
SPECS: Aluminum, painted matte black. 6” (15.2cm) long.
#100-002-822CG M4 Carbine 4-Rail Handguard,
2Z82U80 .........................$ 82.80
NEED IT NOW?!
AsK FOR OVERNIgHT DELIVERy
Models
YANKEE HILL MACHINE AR-15/M16
TACTICAL HANDGUARDS
Fixed Or Removable Rail Models
For Extreme Tactical Duty
Lightweight, vented handguards
allow the shooter to
choose fixed, permanent Picatinny
rails or easily removable
ones for high-level customization.
Precision machined from
aircraft grade aluminum, then
mil-spec hardcoat anodized for
extra strength and superior abrasion resistance. ab
CUSTOMIZABLE FREE-FLOAT TUBE - Versatile forearm system
lets you choose exactly how much rail space you need to accommodate
add-on, tactical accessories. Lightweight, aluminum,
tube free-floats the barrel to eliminate shifts in bullet point-ofimpact
caused by sling or bipod tension on the handguard. Four,
evenly spaced rows of threaded mounting holes accept Yankee
Hill’s Pictainny-type, modular, Add-On Rails. One full-length
rail and one 3" elevated rail included; additional rails available
separately below. Front end is internally threaded to accept the
ported, Yankee Hill End Cap. Included barrel nut features a
slotted lock ring to allow proper indexing of added accessory
rails. Lock ring is best tightened using the Yankee Hill Forearm
Wrench. Choose from Carbine, Specter, or Rifle length tubes.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. Includes
tube, full-length rail, 3" elevated rail, jam nut, and barrel nut.
Carbine - 73 ⁄16" (18.3cm) long x 2” (5.1cm) dia. 9.5 oz. (269 g) wt.
Accepts up to four 3”, 4” or 7” rails. Specter - 95 ⁄8" (24.4cm) long
x 2” dia. 12 oz. (340g). Covers gas block on a carbine-length gas
system; low-profile gas block required. Accepts four 6”, 7”, or 9¼”
rails or a combination of eight 3” and 4” rails. Rifle - 12½” (31.8cm)
long x 2” dia. 14.6 oz. (414 g) wt. Accepts up to four 7”, 9¼” or 12”
rails; eight 3” and 4” rails; four 6” rails and four 3” or 4” rails; four
7” rails and four 3”or 4” rails.
#100-002-078CG Carbine Customizable Tube,
9A91T13 .........................$ 91.13
#100-002-452CG Specter Customizable Tube,
9A100X36 ........................100.36
#100-002-079CG Rifle Customizable Tube,
9A121T90 ........................121.90
“SMOOTH” FREE FLOAT HANDGUARD - Lightweight, machined
aluminum forearm combines
the accessory mounting versatility
of a quad-railed forearm
with a “smooth,” un-railed area
for support hand comfort to aid
in enhanced weapon control. Integral,
full-length Picatinny top rail,
plus forward 2.5" rails on the sides and bottom, offer plenty of
attachment space for lights, lasers, optics, backup sights, and
other accessories. Modular design accepts a variety of bolt-on
YHM accessories, available below. Smooth areas are drilled and
tapped to accept Add-On Rails for additional accessory mounting
options. Side and bottom rails have receptacles for Threaded
Swivel Studs; also accepts YHM Forearm End Cap. YHM’s freefloat
attachment system eliminates accuracy-compromising
pressure on the barrel, while anti-rotation screws prevent the
forearm from working loose even during rigorous tactical operations.
Large ventilation slots allow plenty of air circulation
to dissipate heat and keep the barrel cool. Carbine – Side and
bottom rails extend around the front sight/gas block to get the
accessories as far forward as possible and provide more grasping
surface for the support hand. Cutout on top provides enough
clearance to fold down a Yankee Hill flip-up front sight. Rifle
– Extends to just behind gas block and includes a forward attachment
point for Threaded Swivel Stud on the top rail.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. Carbine
– 9¼” (23.5cm) OAL, 2½” (6.4cm) diameter. 12.4 oz. (352g)
weight. Fits AR-15/M16 with carbine-length gas system. Rifle –
12½” (31.8cm) OAL, 2½” diameter. 16.6 oz. (471g) weight. Fits
AR-15/M16 with rifle-length gas system.
100-004-309CG Smooth Free Float Forearm, Carbine,
9A112X00 .......................$ 112.00
100-004-310CG Smooth Free Float Forearm, Rifle,
9A128X00 ........................128.00
CUSTOMIZABLE 2-PIECE CARBINE HANDGUARD - Two-piece
forearm replaces your AR-15 carbine’s
mil-spec, factory plastic handguard
and allows you to install Picatinny rails
at 45-degree intervals for precise, custom
positioning of lights, lasers, vertical
grips, and other accessories. Eight,
evenly spaced rows of threaded mounting
holes accept Yankee Hill’s Pictainny-type, modular, Add-On
Rails. One full-length rail and one 3" elevated rail included; additional
rails available separately below. Bottom half removes
easily to provide clearance for a shotgun or grenade, flare, or
tear gas launcher. Sixteen, lengthwise cooling vents ensure thorough
dissipation of heat from barrel. Machined from rugged but
lightweight aluminum, then hardcoat anodized matte black for
added strength and exceptional wear resistance.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. 65 ⁄8"
(16.8cm) long x 2” (5.1cm). 7.6 oz. (216g) wt. Accepts up to four 3”,
4” or 6" add-on rails.
#100-002-896CG Customizable 2-Pc Carbine Handguard,
9A116B75 .......................$ 116.75
ADD-ON RAILS - Bolt-on Picatinny
rails give you almost unlimited
accessory mounting options
for your Yankee Hill customizable
handguards. Choose only as much rail as
you need to avoid cluttering handguard with unused
rail space. 6" rail is a full-length rail for Carbine-length
handguards, 9¼" rail is the correct length for Specter tubes, and
12" rail is full-length for Rifle tubes.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. Fits
Yankee Hill Customizable Free-Float and Two-Piece Handguards.
Mounting screws included.
#100-002-081CG 3" Add-On Rail,
9A12T65 .........................$ 12.65
#100-002-082CG 4" Add-On Rail,
9A13T85 ..........................13.85
#100-003-157CG 6" Add-On Rail,
9A16C35 ..........................16.35
#100-002-083CG 7" Add-On Rail,
9A17T25 ...........................17.25
#100-003-158CG 9¼" Add-On Rail,
9A19C85 ..........................19.85
#100-002-080CG 12" Add-On Rail,
9A27T00 .......................... 27.00
4-RAIL FREE-FLOAT HANDGUARD -
Four, integral, full-length Picatinny
rails machined into a single piece of
high-strength, rigid aluminum forms
a handguard that delivers maximum
stability and reliability. Stress-free
tube design ensures complete freefloat
of the barrel for optimal accuracy.
Barrel nut locks in place with two antirotation
screws to ensure handguard
remains locked in place, even under
the added torque from vertical grips. Four, threaded, swivel stud
mounting holes allow attachment of Yankee Hill threaded swivel
stud at the top, bottom, or either side of the handguard. Available
in Carbine or Rifle lengths. Heavy duty, Standard model features
narrow cooling vents that run lengthwise along the handguard.
Lightweight model is a skeletonized version specifically machined
to reduce weight from the rails; oversized cooling holes
provide maximum ventilation and allow clear view of the barrel
for the ultimate tactical look.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. Carbine
Models – 73 ⁄16" (18.3 cm) long x 23 ⁄8" (6 cm) wide. Rifle Models
– 12½” (31.8cm) long x 23 Standard
Lightweight
⁄8" wide. Weight: Standard Carbine - 14.3
oz. (405 g). Standard Rifle - 22.5 oz. (638 g). Lightweight Carbine
- 10.6 oz. (300 g). Lightweight Rifle - 14.75 oz. (418 g).
#100-002-169CG Std Carbine Handguard,
9A91H50 ........................ $ 91.50
#100-002-170CG Std Rifle Handguard,
9A124H62 ........................124.62
#100-003-414CG Lightwt. Carbine Handguard,
9A92H42 ..........................92.42
#100-003-413CG Lightwt. Rifle Handguard,
9A123H05 ........................123.05
MIL/LE sUppLy gROUp Order/Quotes: 1-800-741-0308
2-PIECE HANDGUARD - Tough,
2-piece, forearm uses your existing
delta ring, so it’s easy to replace the
standard issue, mil-spec handguard
with a strong, lightweight aluminum
version. Four, fixed, Picatinny rails
provide a solid mounting platform for backup sights, lasers,
tactical lights, vertical grips and more. Oversize cooling ports
prevent heat buildup and allow clear view of the barrel section
underneath for a radical, tactical look. Bottom panel removes
easily to provide clearance for grenade and flare launchers if
needed. Drilled and tapped in four locations to accept the Yankee
Hill Threaded Swivel Stud. Use Colts Carbine model on Coltmanufactured
guns.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. Carbine
- 65 ⁄8" (16.8cm) long x 23 ⁄8" (6cm) wide. 9.9 oz. (281 g) wt. Colt
Carbine model fits Colt-manufactured guns only. Standard Carbine
model fits carbines made by most other manufacturers. Rifle - 12"
(30.5cm) long x 23 ⁄8" wide. 20 oz. (567 g) wt.
#100-002-093CG Std Carbine 2-Piece Handguard,
9A105P28 .......................$ 105.28
#100-003-122CG Colt Carbine 2-Piece Handguard,
9A105X28 ........................105.28
#100-002-096CG Rifle 2-Piece Handguard,
9A149P25 ........................149.25
TACTICAL SWIVEL MOUNTS - Steel,
swivel stud features a full, 360 degrees
of rotation to allow your tactical
sling to follow the movements of
your body, not just the rifle. Virtually
eliminates sling tangle. Accepts
standard, quick-detach type swivels.
Threaded Swivel Stud is a 5 ⁄16"-32 tpi pivoting stud. Fits Yankee
Hill drilled and tapped handguards. Add-on to other applications
with at least 1 ⁄4" depth clearance. Dovetail Sling Mount
- Threaded Swivel Stud (above), combined with an aluminum
dovetail clamp and steel cross-bolt. Secures directly to any Picatinny
or Weaver-style rail.
SPECS: Threaded Swivel Stud - Steel, blued finish. 5 ⁄16"-32 tpi.
Approx. 3 ⁄4" (1.9cm) OAL, requires 1 ⁄4" (6.4mm) depth clearance for
drill/tap applications. Dovetail Sling Mount - Steel stud, blued;
aluminum clamp, matte black mil-spec hardcoat finish. Approx. 11 ⁄4"
(3.2cm) wide x 11 ⁄4" high.
#100-002-084CG Threaded Swivel Stud,
9A03T55 ..........................$ 3.55
#100-002-087CG Dovetail Sling Mount,
9A16P85 ..........................16.85
FOREARM END CAP - Screws into the front of any
Yankee Hill free-float handguard to provide added
protection for the end of the forearm. Hides view
of the barrel from the front of the handguard for
a clean, finished look, and keeps large debris out.
Cooling ports allow rapid escape of barrel heat
and promote airflow under the handguard. Available
with 15 ⁄16" or 11 ⁄16" inside diameter. Install using supplied
threadlocker.
SPECS: Aluminum, mil-spec hardcoat anodized, matte black. 15 ⁄16"
(2.4cm) I.D. or 11 ⁄16" (2.7cm) I.D.
#100-002-897CG 15 ⁄16" I.D. End Cap,
9A13B85 .........................$ 13.85
#100-002-086CG 11 ⁄16" I.D. End Cap,
9A13T85 .......................... 13.85
FOREARM WRENCH - Heavy, steel,
spanner wrench makes it easy to
tighten handguard barrel nuts to the
correct torque. Notched end engages
the indexing ring on Yankee Hill
handguards and others with similar,
slotted indexing rings for aligning the accessory rails.
SPECS: Steel, black oxide finish. 8" (20.3cm) long, 2" (5.1cm) wide,
1 ⁄4" (6.4mm) thick.
#100-002-090CG Forearm Wrench,
9A22P05 .........................$ 22.05
sELECTION • sERVICE • sATIsFACTION