FREE POSTER OFFER INSIDE! - Brownells

mounts & optics
42
SOG ARMORY
AIMPOINT
MOUNT
Strong, Lightweight;
Standard & Offset Models
Single-ring mounts of
strong, lightweight aluminum secure your Aimpoint or similar
aiming device to any Picatinny or Weaver-style rail. Extra-large
ring surface area ensures zero scope movement under recoil, with
six Torx T-15 screws (wrench included) securing the ring halves.
A cross-bolt with integral recoil lug and .510" diameter hex nut
anchor the mount to the rail. Standard model elevates the sight
to the correct height to co-witness with a back-up iron sight.
Cut-out in the base reduces weight without sacrificing strength.
Cantilever-style Setoff model provides co-witness elevation and
positions sight 1¼" forward to make room for a rear-mount night
vision device. Both models accept 30mm diameter scope tubes;
aluminum reducer included for mounting a 1" tube.
SPECS: Aluminum, hardcoat anodized, matte black. Steel Torx
screws cross-bolt, oxide finish, black. Fits 30mm and 1” diameter
sights. Standard Model – 1” (2.5cm) long, 1” high from top of base
to bottom of ring. Setoff Model – 3 3 ⁄8" (8.6cm) long, 1” high from
top of base to bottom of ring.
#100-003-048CG Standard Mount,
9A47H95 .........................$ 47.95
#100-003-047CG Offset Mount,
9A63H95 ..........................63.95
YANKEE HILL AR-15/M16
EOTECH RISER MOUNT
Keeps Iron Sights
From Blocking EOTech Reticle,
Preserves Co-Witness
Capability
Rugged, yet lightweight riser mount positions your EOTech
holographic sight .300" higher, so your rifle’s iron sights are less
apt to interfere with the EOTech’s reticle, while preserving cowitness
capability. Also helps you maintain a more comfortable,
heads-up shooting form. Clamps to your flattop rifle’s Picatinny
rail with a single hardened steel setscrew; a securing tab up front
locks into one of the rail’s slots to ensure a solid, recoil-proof fit.
Precision machined from solid aluminum, then mil-spec hardcoat
anodized for extra strength and wear resistance. ab
SPECS: Aluminum, hardcoat anodized, matte black. 5 3 ⁄16” (13.5cm)
long, 1 3 ⁄16” (4.6cm) wide, .525” (1.3cm) overall height. 2.5 oz. (70g)
weight. Fits AR-15/M16 with flattop receiver only.
#100-003-101CG EOTech Riser Mount 9A31B55 ....$ 31.55
BADGER ORDNANCE
MAXIMIZED
SCOPE RINGS
Extra Strong To Withstand Heavy Recoil
Heavy duty 30mm steel rings, machined in
pairs, serial numbered, and designed specifically
to securely hold large, heavy scopes on
hard-recoiling guns. Weaver-style clamp with big 1 Ultra-High
⁄2" nut really
snugs ring to the mount. Ultra-High provides optimum height
for AR-15, AR-10 and SR-25 rifles. Ring reducers convert 30mm
to 1". ab
SPECS: Steel, black,matte finish. Ring height measured from top
of mount to center of ring; Standard - .823" (2cm), Medium - .885"
(22.5mm), Medium High - 1.0" (2.5cm), High - 1.125" (2.8cm), Ultra
High - 1.378" (3.5cm). Weights; Standard - 6.6 oz (187 g), High - 9
oz. (255 g), Ultra High - 10 oz. (284 g).
#093-306-080CG Standard Ring 3K141B34 ........$ 141.34
#093-306-001CG Medium Scope Ring 3K146P58 ....146.58
#093-306-002CG Med. High Scope Ring 3K146P78 . . 146.78
#093-306-090CG High Ring 3K152B85 .............152.85
#093-306-100CG Ultra High Ring 3K154B29 .......154.29
#093-306-120CG 1" Standard Reducers 3K29B35 ....29.35
LEUPOLD MARK 4
RINGS
Rock-Solid, Heavy-Duty
Mounts For Extreme Field
& Tactical Use
Heavy-duty rings are built to
withstand extreme service without movement or loss of zero.
Larger contact area between the scope/rings and base/receiver
for less chance of movement. Large hex nuts on rings allow fast
torquing of cross bolts for easy adjustment. Non reflective, matte
finish. Mounting screws and Torx ® head wrench included. Steel
Rings - CNC machined from solid 11L17 cold-rolled bar stock,
then blued. Aluminum Rings – CNC machined from 7075 T651
aluminum alloy and hardcoat anodized for maximum strength
and wear resistance.
SPECS: Steel or aluminum, matte black finish 1" (2.5cm) or 30mm
(1.18in) inside diameter. Height from top of base to center of ring
for both 1" and 30mm: Med. - .84" (2.1cm); High - 1.06" (2.7cm);
Super High - 1.4" (3.5cm).
#526-000-085CG 1" Med. Aluminum Rings,
6B131A31 .......................$ 131.31
#526-502-220CG 1" Super High Steel Rings,
6B131Y31 ........................131.31
#526-000-086CG 1" Super High Aluminum Rings,
6B131A31 ........................131.31
#526-000-082CG 30mm Med. Aluminum Rings,
6B131A31 ........................131.31
#526-000-053CG 30mm High Steel Rings,
6B131U31 ........................131.31
#526-000-083CG 30mm High Aluminum Rings,
6B131A31 ........................131.31
#526-520-830CG 30mm Super High Steel Rings,
6B131U31 ........................131.31
#526-000-084CG 30mm Super High Aluminum Rings,
6B131A31 ........................131.31
LIGHTFORCE
NIGHTFORCE 30mm TACTICAL RINGS
Extra Strong For Police
& Military Applications
Milled from barstock, these
rings provide the solid strength
required for harsh field and tactical
use. With four TORX screws
per cap, the scope is securely
locked into the ring to prevent recoil
movement. Large, 1 ⁄2" hex nut lets you torque ring securely
to any MIL-STD 1913 Picatinny base, and helps achieve a consistent
return to zero. Steel cross lug provides additional strength,
prevents shifting caused by recoil. ab
SPECS: Steel, parkerized, matte finish. 30mm I.D. 5 ⁄8" (15.9mm)
wide. Height measured from top of base to bottom of scope body:
Low - .300" (7.6mm), Medium - .400" (10.2mm), High - .535"
(13.6mm). Extra High - .782" (19.9mm). Fits Picatinny bases.
#524-000-001CG Low Tactical Rings,
4B150Y53 .......................$ 150.53
#524-000-002CG Medium Tactical Rings,
4B151Y72 ........................151.72
#524-000-003CG High Tactical Rings,
4B151Y72 ........................151.72
#524-000-017CG Extra High Tactical Rings,
4B150Y68 ........................150.68
Shop
tactical rings
brownells.com
Search
TACTICAL PRECISION
TSR & TSR "W" RINGS
Super Holding Power, Precision Alignment
Rugged tactical rings are precision machined
to tolerances of .0002" for maximum
scope/ring contact to hold scope securely
against recoil. Four-screw cap lets you align
the reticle, tighten the left side of the cap,
then the right side without the scope rotating.
Large clamp-nut lets you torque ring to base. Radiused edges
and corners help prevent snagging while providing attractive
appearance. TSR - 7075-T6 aluminum, fits MIL-STD 1913 Picatinny
base. TSR "W" Series - 1215 alloy steel, fits Weaver bases.
34mm - Accepts Schmidt & Bender-type 34mm scope tubes. ab
SPECS: 5 ⁄8" (15.8mm) wide. Heights measured from top of base to
center of ring. TSR - 7075-T6 Aluminum black, hard anodized to Mil-
A-8625 standards. TSR "W" Series - 1215 alloy steel, Mil-C-13924
oxide finish, matte black. 1" - Low: .785" (19.9mm). Medium: .985"
(25mm). High: 1.185" (30mm). 30mm - Low: .925" (23.5mm). Medium:
1.075" (27.3mm). High: 1.225" (31.1mm). 34mm - Medium:
1.185" (30.1mm). High: 1.435" (36.4mm).
TSR ALUMINUM RINGS
STOCK # HEIGHT SIZE PRICE
#100-000-951CG Low 1” 9K45A00 $ 45.00
#100-000-952CG Med 1” 9K45A00 $ 45.00
#100-000-953CG High 1” 9K47A00 $ 47.00
#100-000-957CG Low 30mm 9K48A00 $ 48.00
#100-000-958CG Med 30mm 9K48A00 $ 48.00
#100-000-959CG High 30mm 9K50A00 $ 50.00
TSR “W” SERIES STEEL RINGS
STOCK # HEIGHT SIZE PRICE
#100-001-403CG Low 1” 9K50T00 $ 50.00
#100-001-404CG Med 1” 9K50T00 $ 50.00
#100-001-405CG High 1” 9K52T00 $ 52.00
#100-001-409CG Low 30mm 9K55T00 $ 55.00
#100-001-410CG Med 30mm 9K60T66 $ 60.66
#100-001-411CG High 30mm 9K57T00 $ 57.00
100-003-300CG Med 34mm 9K75Y00 $ 75.00
100-003-299CG High 34mm 9K85Y00 $ 85.00
LEUPOLD
PRISMATIC RIFLE SCOPE
Combines The On-Target
Speed Of A Red Dot
With The Reliability
Of A Traditional Scope
Compact, 1x magnifying
optic combines the fast target
acquisition, accuracy,
and low-light capability of
a red dot sight with the reliability and clarity of a traditional rifle
scope. Allows easy, both-eyes-open sighting that preserves depth
perception and peripheral vision for quick reaction to changes
in target—perfect for tactical operations or hunting applications
that require a low-magnification scope. Battery powered illumination
module clamps to the side of the tube and illuminates the
reticle in red for maximum contrast with target. Eight brightness
settings let you adjust the intensity of the crisp, circle-andcrosshairs
reticle for light conditions varying from bright daylight
to night time. Reticle is etched in the glass of the high-grade
optic system, so it’s visible at all times, sharp and clear without
fuzziness, even when the illuminator is shut off or suffers battery
failure. Or remove illumination module completely for minimal
weight and bulk. Fully adjustable for windage and elevation in
precise ½ MOA clicks, with a 70 MOA adjustment range. Focusing
eyepiece allows adjustment to suit individual shooters.
DiamondCoat 2 lens treatment enhances light transmission
and helps protect lens surface from abrasion and scratches.
Includes integrated base with three optional height spacers to
mil/le supply group Order/Quotes: 1-800-741-0308
Items
LEUPOLD AR-15
MARK 4 CQ/T SCOPE
Speed Of A
Shown with optional
Flat Top Mounting Bracket
Red-Dot,
With The Precision
Of A Rifle Scope
Multi-function,
red-dot and optical
sight has variable
power settings
for fast, accurate
engagement of targets out to 300 yards and beyond. Variablebrightness
Circle-Dot reticle gives accurate ranging plus holdover
and lead on moving targets. Mil-Spec, Picatinny rails, on the
top and right side, for lights, night vision gear or laser designators.
Fits A2, carry handle receivers.
SPECS: Black, matte finish. 8.8" (22.4cm) long. 2" to 2.8" (5.1 to
7.1cm) eye relief. 17.5 oz. (496 g) wt. 1 ⁄2 MOA click adjustments.
Dot size: 3MOA at 3X, 9 MOA at 1X. Circle size at 3X: 18" at 25
yards, 6' at 100 yards. Uses (1) AA battery (not included). Includes
lens covers.
#526-521-550CG Mark 4 CQ/T Scope,
6B899U99 .......................$ 899.99
FLAT TOP MOUNTING BRACKET -
Mounts the Mark 4 CQ/T scope to flattop
AR-15 or any Picatinny base. Tough and
rugged with heavy-duty crossbolts for
hard, field use.
SPECS: Steel cross bolts, aluminum bracket
rails, black, matte finish. 23 ⁄4" (7cm) long.
#526-000-043CG Flat Top Mount Bracket,
6B37U52 .........................$ 37.52
LEUPOLD
MARK 4 ® 4.5-14X 50mm LR/T
LONG RANGE TACTICAL SCOPE
30mm Tube For Maximum Light Transmission & Clarity
Variable-power, tactical scope has high resolution optics, repeatable
accuracy and rugged, waterproof construction with
the durability to withstand harsh operating conditions. 50mm
objective and Multi-coat 4 lens coating provide maximum light
transmission in low light conditions. Front focus adjustment lets
you eliminate parallax and stay in shooting position; your eyes
never leave the target. Windage and elevation knobs have 1 ⁄4
MOA audible click adjustments and 75 minutes total adjustment.
Easy-to-use, target-style knobs reset to zero. Mil-Dot
reticle with instructions.
SPECS: Black, matte finish. 30mm tube diameter. 50mm objective
lens diameter. 12.5" (31.7cm) long. Weight 22 oz., (624g). 4.5-14X
magnification. 100 yd. field of view: 4.5, 20.5' (6.8mm); 14, 7.6'
(2.5m). Requires high rings.
#526-000-064CG Long Range Tactical Scope,
6B1249U99 ....................$ 1,249.99
accommodate mounting on almost any firearm with Picatinny or
Weaver-style rails. Also compatible with standard 30mm scope
rings and A.R.M.S. #22 quick-detach throw-lever rings. Heavy
duty, extra-thick walled tube, plus sealed, fogproof and waterproof
construction stands up hard use.
SPECS: Aluminum, anodized, matte black. 4 3 ⁄8" (11.1cm) long, 2”
(5.1cm) maximum width with Illumination Module installed. 30mm
diameter tube. 8.4 oz. (237g) weight without base. Eye relief: 3”
(7.6cm). Uses (1) DL1/3N button-type battery, included.
#526-000-090CG Prismatic Rifle Scope,
6B499A99 .......................$ 499.99