FREE POSTER OFFER INSIDE! - Brownells

TOOLS cleaning
58
PROFESSIONAL
ASSEMBLY/DISASSEMBLY MAT
Don’t Scratch Up Those Parts
While Working On Guns
Heavy, neoprene mat provides a
padded surface for all kinds of gun
servicing. Slightly “grained,” hard
enough to keep dirt from embedding;
cleans up easily with soap
and water. Resists most solvents
and oils. Rolls up easily so you can add it to your range kit and
have a “no-scratch” surface available. ab
SPECS: Small Mat: 17 1 ⁄2" (44.4cm) long. 12" (30.5cm) wide. 3 ⁄16"
(4.7mm) thick. Large Mat: 36” (91.4cm) long, 24” (60.9cm) wide.
1 ⁄8” (3.1mm) thick. Weighs 1 1 ⁄2 lbs. (680 g).
#358-128-316CG Small Mat 8E17V97 ..............$ 17.97
#358-128-416CG Large Mat 8E42V08 ...............42.08
Brownells
NYLON/BRASS DRIFT PUNCH
6 Indispensable Mar-Proof Punches
Great combination punch for gunsmith, machinist and toolmaker.
Hi-impact steel handle with knurled grip for easy holding
and accurate control. Built to withstand maximum impact
with a minimum of distortion. Interchangeable and replaceable
tips are available in: Nylon with steel reinforcing pin to prevent
bending or breakage while giving completely mar-free punching
action; Brass for a harder-than-nylon but softer-than-steel
impact where slight discoloration is acceptable. Remington
Shotgun Punch Tip for removing trigger plate pins from 870,
1100 and 1187. Supplied as: Basic Set with two 5 ⁄16" diameter
tips (one Nylon, one Brass) and one Handle. 4-Way Set includes
four Handles, one 5 ⁄16" Nylon Tip; plus one each, 3 ⁄16", 1 ⁄4" and
5 ⁄16" diameter Brass Tips. 6-Way Set adds 1 ⁄4" and 5 ⁄16" diameter,
Aluminum Tips and 2 more handles to the 4-Way Set. ab
SPECS: Handle 3" (7.6cm) long x 3 ⁄8" (9.5mm) diameter. Tips are
1 1 ⁄4" (3.2cm) long.
#080-475-001CG Nylon Punch Tip 8K02Y83 .........$ 2.83
#080-475-002CG 5⁄16" Brass Punch Tip 8K02Y92 .......2.92
#080-475-003CG ¼" Brass Punch Tip 8K03Y62 .......3.62
#080-475-004CG 3⁄16" Brass Punch Tip 8K02Y81 .......2.81
#080-475-005CG ¼" Alum Punch Tip 8K03Y69 ........3.69
#080-475-006CG 5⁄16" Alum Punch Tip 8K03Y84 .......3.84
#080-000-209CG Rem. Shotgun Punch Tip 8K04X03 . . 4.03
#080-475-000CG Basic N/B Punch Set 8K05A79 ......5.79
#080-475-100CG 4-Way N/B Punch Set 8K14Y74 .....14.74
#080-475-106CG 6-Way Punch Set 8K19Y97 .........19.97
STARRETT #565 PIN PUNCH SET
Precision Ground Beautifully Polished
Precision ground from specially selected tool
steel, hardened and highly polished, the Star- rett
Pin Punches are well proportioned and beautifully
finished. Blued, knurled grip area; individually
marked for size. Set of all 8 punches comes in
handy, fitted, round, hard plastic bench box. Also
available singly. ab
SPECS: 4" (10.2cm) long. Sizes: 1 ⁄16" (1.6mm), 3 ⁄32"
(2.4cm), 1 ⁄8" (3.2mm), 5 ⁄32" (4mm), 3 ⁄16" (4.8mm), 7 ⁄32"
(5.5mm), 1 ⁄4" (6.3mm) and 5 ⁄16" (7.9mm).
STOCK # SIZE STOCK # SIZE
#827-525-780CG 1 ⁄16" #827-525-820CG 3 ⁄16"
#827-525-790CG 3 ⁄32" #827-525-830CG 7 ⁄32"
827-525-800CG 1 ⁄8" #827-525-840CG 1 ⁄4"
#827-525-810CG 5 ⁄32" #827-525-850CG 5 ⁄16"
— Advise # — Starrett Pin Punch, each 8K00YTP .$ 4.99
#827-525-860CG Starrett Pin Punch Set #565,
7B00XCH .........................49.99
Brownells
MULTI-VISE
Easily Adaptable &
Versatile, Quality
Construction
That Lasts and Lasts
Don’t adjust jobs to your
vise; adjust your Multi-Vise
to the job. Multi-Vise adjusts in every direction a job can take
you…position it horizontally, vertically, and rotate it 360° in a
horizontal plane. Multi-Vise adapts to nearly any job; drilling,
filing, stock work, soldering, sanding, and the holding of darn
near anything. ab
The highest quality U.S. materials and craftsmanship go into
producing the Multi-Vise. The body is constructed of tough,
50,000 psi tensile strength, ductile, iron, which makes it last and
last. You won’t have to tighten or loosen extra clamps when you
turn Multi-Vise on its side or rotate it back and forth, because the
convenient cam locking system automatically locks the Multi-
Vise in position when you tighten the jaws. Precision-machined,
smooth, jaw faces combine firm pressure with a gentle finesse
to securely hold metal, wood, or plastic. The 4140, chrome-molysteel,
nickel-plated, rust-resistant lead screw turns effortlessly.
Multi-Vise, the most versatile vise ever offered to professional
gunsmiths and home hobbyists, is also backed by Brownells
100% satisfaction guarantee. Upgrade to the Multi-Vise today...
your jobs will be easier tomorrow!
SPECS: Cast iron body, precision-machined, green paint. Jaws
are 3 1 ⁄2" (9.0cm) x 2 1 ⁄2" (6.3cm), opens to 5" (12.7cm). 1 3 ⁄4" (4.4cm)
square anvil. 18 lb. (8kg) wt.
#080-000-019CG Multi-Vise, Complete 8K228Y96 ...$ 228.96
#080-000-048CG Multi-Vise, Body 9Z71T77 ..........71.77
#080-000-050CG Multi-Vise, Movable Jaw 9Z56T22 ...56.22
#080-000-052CG Multi-Vise, Standard Base 9Z18T75 . . 18.75
#080-000-006CG Multi-Vise, Handle w/knobs,
2C32Y22 ..........................32.22
#080-000-046CG Multi-Vise, Lead Screw 9Z24T94 ....24.94
#080-000-049CG Multi-Vise, Lead Screw Nut 2C16T18 16.18
#080-000-051CG Multi-Vise, Cam 9Z16T16 ..........16.16
#080-000-047CG Multi-Vise, Knurled Pin 9Z04T44 .....4.44
#080-000-053CG Multi-Vise, Dog Point Screw, 2-pak,
9Z02T44 ...........................2.44
Br o w n e l l s ULTRASONIC
CLEANING SOLUTION & OIL
Advanced Formulas
Power Away Dirt & Fouling;
Lubricates, Fights Corrosion
Powerful, fast-acting cleaning
and lubricating solutions are specially
formulated for today’s ultrasonic
gun cleaning systems to
thoroughly clean, condition, and
protect your firearms. Safe for
all metal surfaces, including carbon steel, aluminum, titanium,
and stainless steel. Won’t harm bluing, parkerizing, anodizing,
or most paints. Environmentally safe, non-toxic, ammonia-free,
and biodegradable with minimal odor, so both products can be
safely used right in the shop. Cleaning Solution penetrates
petroleum-based greases and oils and removes carbon fouling,
dirt, grime, and powder residue to leave the metal completely
clean. Gets into nooks and crannies for thorough, deep-down,
“in the pores” cleaning without completely disassembling firearm.
Economical, concentrated formula: mix 1 gallon of solution
with 9 gallons of water to produce 10 gallons of cleaner. Waterdisplacing
Oil with “Thin Coat” technology drains quickly from
parts without puddling and leaves a microscopic layer of longlasting
corrosion protection. Ultra-low friction coefficient helps
minimize wear on moving parts for smooth firearm operation
and improved reliability. ab
SPECS: 1 gal. (128 fl. oz./3.8 liters) plastic jug.
#083-000-031CG Ultrasonic Cleaning Solution, 1 Gal.,
3H29T95 .........................$ 29.95
#083-000-032CG Ultrasonic Oil, 1 Gal. 3H32T95 .....32.95
CREST ULTRASONICS
FIREARMS
CLEANING & LUBRICATING SYSTEM
Powerfully Removes Gun Powder, Carbon Dirt & Oil
In Just Minutes; Leaves Entire Firearm Clean & Lubricated
A real time saver for the busy shop or department armorer
with lots of guns to clean. Advanced technology uses a combination
of heated cleaning solution and ultrasonic frequency
vibrations to “scrub” firearms clean, providing a quick and easy
alternative to hand cleaning. Exclusive Tru-Sweep frequency
sweeping penetrates and cleans even the smallest crevices leaving
heavily-fouled, field-stripped firearms restored to factory
new cleanliness and ready for lubrication or refinishing. Complete
systems with large capacity tanks allow multiple firearms
to be cleaned at one time. ab
F1200HT -
Benchtop systemsimultaneously
cleans
four handguns
or one submachine
gun.
Constant power
generator
with ceramic
enhanced
transducers produces higher frequencies than was previously
possible, resulting in superior contaminant removal while reducing
damage to sensitive parts. Complete kit includes adjustable
temperature control with on/off switch, stainless steel
heated tank, 30 minute timer, rear drain with pinch valve, two
full-length heavy duty mesh baskets with handles, lube pan,
two tank covers, 1 gallon of cleaner concentrate and 2 gallons of
lubricant. Cleans approximately 500 guns per gallon of cleaner.
SPECS: Tank – 316L annealed stainless steel. 19½” (50cm) long,
5½” (14cm) wide, 6” (15cm) high. 2½ gal. (9.5 L) capacity. Current
Draw - 8 amps @ 115 VAC. Shipping weight 65 pounds.
#223-000-003CG F1200HT Ultrasonic System,
3B1958Z58 ....................$ 1,958.58
F636HT - Designed for
fast turnaround on
large volume cleaning
– up to 10 handguns or
4 long guns at once. A
real time saver for the
busy shop or department
armorer with
lots of guns to clean.
Exclusive Tru-Sweep ,
ultrasonic technology is powerful enough to thoroughly clean
heavily-fouled, field-stripped firearms in just minutes; leaves
them ready for lubrication or refinishing. For multiple firearm
cleaning operations, actual output is increased many times over
hand cleaning; parts are restored to a uniform standard of factory
new cleanliness. Industrial-quality stainless steel tank includes
drip-proof flange, built-in carry handles and full width
V-bottom oil pan with anti-splash dampers. Standard 2,000 watt
adjustable tank heater plus sound/thermal insulation maintains
water temperatures up to 200° F without dead or hot spots
for fast, uniform cleaning end to end; lets you parkerize guns in
the same tank. Separate power unit with variable power adjustment
and half wave power switch allow full control of cleaning
intensity. Guns come out ready for a hot water rinse followed by
ultrasonic lubrication. Kit includes one, full-length lube pan, two
heavy-duty, weapon racks with five removable compartments,
lube pan cover, tank cover, 2 gallons CC235 cleaning concentrate,
and 6 gallons of CC400L lubricant; enough to clean and lubricate
up to 1,000 guns.
SPECS: Tank - 14 ga. 316L annealed stainless steel, bright finish.
36" (91cm) x 6" (15cm) x 8" (20cm). 53 ⁄4 gal. (21 L) capacity. Racks (2)
and Lube Pan - Stainless steel 351 ⁄2" (90cm) long, 6" (15cm) wide.
Heater-16 amps @ 120 VAC, requires 20 amp dedicated circuit. Generator-8
amps @ 120 VAC. Shipping weight 240 pounds.
#223-636-000CG F636HT Ultrasonics Systm,
3B7453Z31 .................... $ 7,453.31
(Shipped Truck only. Please call for freight charges.)
mil/le supply group Order/Quotes: 1-800-741-0308
L&R HCS-200 ULTRASONIC
HANDGUN CLEANING SYSTEM
Gets Dirty Guns Clean In Minutes;
Perfect For Small Shops Or The Hobbyist
Clean and lubricate up to two semi-automatics, or one 6" revolver,
in less than 20 minutes with powerful, ultrasonic cleaning
action. Billions of tiny, scrubbing bubbles get cleaning solution
into the nooks and crannies that are hard to reach by hand.
Field strip the firearm, place it in the wire basket, turn on the
Ultrasonic Cleaner and you’re free to do other things while the
cavitating action gets everything super-clean! An ideal solution
for the small shop where only a few firearms need to be cleaned
and for hobbyists who want to give their guns a professional
cleaning. Also great for cleaning powder residue from empty
cases before reloading.
Input: 117V Dimensions: 121 ⁄2"(31.75cm) x 63 ⁄4" (17.14cm)
Peak Output: 95 Watts Tank Dimensions: 113 ⁄4" (29.8cm) x 6"
(15.2cm) x 4" (10.2cm) Tank Capacity: 47 ⁄8 Quarts
Output Frequency: 43 KHz
SPECS: Tanks, lid, auxiliary pan and wire basket are stainless steel.
System includes: (1) HCS-200 Ultrasonic Cleaner, (1) Auxiliary pan,
(1) Wire basket, (1) lid, (1) Gallon (3.80l) Handgun Lubricating Solution,
(2) 8 oz. (0.23kg) Concentrated Handgun Cleaning Solution,
(1) pair latex gloves, (1) 0.4 oz. (11.8ml) tube Synthetic Gun Oil, (1)
Cleaning Brush, (1) cotton cleaning pad.
#515-000-006CG HCS-200 Ultrasonic Cleaning System,
5A00ZAY ........................$ 399.00
#515-000-007CG Cleaning Solution for HCS-200, 8 oz.,
5A03P99 ...........................3.99
#515-000-005CG Lubricating Sol., 1 Gal 5A59Z16 ....59.16
F500HT - Cleans
two full size semiauto
pistols or small
frame revolvers, or
one six inch revolver.
Constant power generator
with ceramic
enhanced transducers
produces higher
frequencies than was
previously possible for better cleaning. Includes temperature
control with on/off switch, stainless steel tank, 30 minute timer,
two mesh baskets, lube pan, two tank covers, 1 gallon of cleaner
and 2 gallons of lubricant.
SPECS: Tank – 316L annealed stainless steel. 11½” (29cm) long,
6” (15cm) wide, 6” high (15cm). 1½ gal. (5.7 L) capacity. Current
draw - 3 amps @ 115 VAC. Shipping weight 31 pounds.
#223-000-002CG F500HT System 3B1469Z54 ....$ 1,469.54
CC-235 ULTRASONIC CLEANER - Non-hazardous;
water based, non-ammoniated cleaner; completely
biodegradable, odorless, won’t hurt tritium sights and
actually helps inhibit rust.
SPECS: 1 gal. (128 fl. oz./3.8 L). Mixing ratio 4-6 oz. per
gallon of water.
#223-235-128CG CC235 Cleaner 3B68Z31 ..........$ 68.31
CC-400L ULTRASONIC LUBRICANT - Use after water
rinse; completely displaces moisture and leaves the
weapon with a light, lubricating film that reduces
friction, wear, and protects against rust. Non-hazardous;
odorless and solvent free. Won’t harm rubber
grips or tritium sights.
SPECS: 1 gal.(128 fl. oz./3.8 L)
#223-400-128CG CC400L Lubricant 3B78Z56. . . . . . .$ 78.56