FREE POSTER OFFER INSIDE! - Brownells

R&R TARGETS
SCOPE THROW LEVERS
Easy To Grasp Lever For Fast,
Precise Changes In Scope
Magnification Setting
Machined aluminum extension lever
clamps over your variable-power scope’s
magnification adjustment ring to provide an oversized grasping
surface and extra leverage for fast, precise changes to magnification
setting. Perfect for multi-gun competition shooters, as
well as military/law enforcement operators, who need to quickly
change scope settings for best accuracy. Over-engineered for
strength and reliability, the clamp completely surrounds the
scope’s adjustment ring and is secured with two, steel, hex-head
screws for a full-contact, no-slip fit. Durable, wear- and corrosion-resistant
matte black anodized finish. ab
SPECS: Aluminum, anodized, matte black. Leupold Mark 4 fits
non-illuminated Mark 4 models only. Leupold Mark 4 CQ/T fits
CQ/T self-illuminating tactical model only. Trijicon AccuPoint
fits AccuPoint scopes with 1.270” O.D. adjustment ring. Recentproduction
AccuPoints may require removal of adjustment ring’s
rubber cover for proper fit.
#100-004-390CG Scope Throw Lever, Leupold Mark 4,
5B62Z77 .........................$ 62.77
#100-004-389CG Scope Throw Lever, Leupold Mark 4 CQ/T,
5B62Z77 ..........................62.77
#100-004-391CG Scope Throw Lever, Trijicon AccuPoint,
5B62Z77 ..........................62.77
GG&G EOTECH LENS COVER MODULE
Fast, Flip-Open Design;
Protects The Lenses
From Weather & Damage
Flexible rubber body with spring-loaded,
ABS plastic covers help seal out dirt,
dust and moisture to keep the lens surfaces
of your EOTech holographic sight clean, scratch-free, and
ready for use in all shooting conditions. Integral tabs on the right
and left sides of the covers allow a fast, ambidextrous flip-open
action with thumb or finger pressure. Front cover opens to near
horizontal position to help block rain or sunlight. Rear cover
folds back on top of the EOTech’s protective hood for compactness,
and to ensure a completely unobstructed view through the
sight. Body section installs under the EOTech protective hood,
so it can’t be lost or damaged. Fits EOTech models 511, 512, 551,
and 552. Included, noise-absorbing neoprene pads dampen the
sound of the rear lens cover contacting the hood during covert
operations. ab
SPECS: Rubber body, ABS plastic covers, neoprene pads, matte
black. 2 3 ⁄8" (5.9cm) long, 1 7 ⁄8" (4.8cm) wide, 1 7 ⁄16" (3.6cm) high. 1 oz.
(28.4g) weight. Includes Torx wrenches for installation.
#336-000-007CG EOTech Lens Cover,
6C35T21 .........................$ 35.21
MICHIGUNS
EOTECH ADJUSTMENT DECALS
Elevation & Windage Calibrated
Decals For Fast Adjustments
Calibrated decals are placed on the
outside of the EOTech protective housing,
around the elevation and windage
knobs to allow fast, precise sight adjustments
on distant targets. Large,
easy to see arrows avoid confusion by pointing in the direction
of turn to change elevation and windage. Transparent with tan
colored lettering and markings that are easy to see. Each calibrated
“tic” mark is the equivalent of ½" of bullet point-of-impact
at 100 yards. Constructed of waterproof, high-strength vinyl,
with an adhesive backing that holds tight. ab
SPECS: Vinyl decal. Calibration - ½” @ 100 yards.
#100-003-668CG Adjustment Decals,
3Z06A95 ..........................$ 6.95
Item
Provides Extremely Fast,
Heads Up Target Engagement
For Close Quarters &
Long Range Shooting
EOTECH
HOLOGRAPHIC SIGHT
Weatherproof, shockproof, night
vision compatible sight provides
competitive, military and law enforcement
shooters a versatile, allweather
sighting system. Holographic, variable-intensity reticle
is visible in any light. As long as the operator can see through
any portion of the window, the entire reticle is visible on target.
All models (except 552.XR308) feature a dot-within-a-circle
reticle that presents a see-through pattern for lightening-quick
target acquisition. Heads-up display eliminates blind spots and
tunnel vision. Gives true, both eyes open shooting for instant
target identification. Electronics are encapsulated in a shock
absorbing resin compound and sealed against dirt and water.
Shatterproof lens has an anti-reflective coating. Light signature
is not visible from the front. All user controls are flush with the
housing, no protruding knobs or mounting rings to snag or block
vision. Integral mount fits Weaver-style and Picatinny bases.
Aluminum “roll bar” hood protects display. Model 553 incorporates
the patented ARMS ® dual quick-release throw levers for
instant on/off capabilities. Zero is repeatable to 1 MOA after
re-mounting. Sight body sets 7mm (.275") higher to provide operator
with a consistent cheek weld with all other standardized
optics. Model 555 offers the same feature set as the 553 with the
added convenience of using two common 1.5 volt AA batteries
as a power source. Gives 1,000 hours continuous operation with
lithium batteries at nominal setting 12; 600 continuous hours
with alkaline. Also compatible with AA rechargeables. Model
552, 552.XR308, 553, and 555 are night vision compatible with a
night vision brightness range of 1,000:1 with NV switch engaged.
Model 552.XR308 has a ballistic drop compensated reticle for
.308 caliber with hash marks calibrated for 600, 900, and 1200
meters. Models 511 and 512 have no provisions for night vision
equipment. 511 uses two, Type N batteries; 512, 552, and 555
use two, AA batteries; 553 uses two, CR123A (3v) batteries. All
include batteries. ab
SPECS: Polycarbonate body, aluminum hood, matte, black. Lens -
3 ⁄16” thick, 3-layer, shatterproof laminate glass. Reticle size: 1 MOA
dot and 65 MOA ring. 511 - 4” (10.2cm) long, 1 15 ⁄16” (4.9cm) wide,
2 3 ⁄8” (6cm) high. 9.2 oz. (262 g) wt. 512, 552 & 552.XR308 - 5
5 ⁄16” (13.5cm) long, 1 15 ⁄16” wide, 2 3 ⁄8” high. 11.5 oz. (326 g) wt.
553 - 4 15 ⁄16” (12.4cm) long, 1 15 ⁄16” wide, 2¾” (7.1cm) high, 12.2
oz. (345g) wt. 555 – 5 9 ⁄16” (4.9cm) long, 2¾” wide, 2¾” high, 12.5
oz. (354g) wt.
#100-000-907CG 511 Holographic Sight,
9K385Z33 .......................$ 385.33
#100-001-738CG 512 Holographic Sight,
9K399T99 ........................399.99
#100-000-909CG 552 Holographic Sight,
9K509Z33 ........................509.33
#100-003-196CG 552.XR308 Holographic Sight,
9K577T33 ........................ 577.33
#100-002-871CG 553 Holographic Sight,
9K665B33 ........................665.33
#100-003-474CG 555 Holographic Sight,
9K639H99 ........................639.99
MODELS 516, 556 & 557 - Flushmounted
control buttons positioned
on the left side of the unit
ensure easy, fast access when backup
iron sight or EOTech Magnifier
is installed. Integral mount with
knurled cross-bolt locks securely
MIL-STD 1913 Picatinny and
Weaver-style rails; zero is repeatable to 1 MOA after removing
and re-mounting. Front one-third of the base underside is
elevated .275" (7mm) for clearance over delta ring and standard
military-style plastic handguard. Submersible to 33 ft. depth.
Models 516 and 556 occupy only 3¼" of rail space, leaving
adequate room for a backup iron sight. Both have an easy-toacquire
tactical reticle with a 1 MOA dot inside a 65 MOA ring
and provide up to 1,100 hours of continuous operation on two
YANKEE HILL
EOTECH REPLACEMENT SCREW
Oversize Head
Makes Attaching
Your HoloSight Easier
Fully machined, heat-treated
thumbscrew with oversize, slotted
head protrudes farther out
from the side of your EOTech
holographic sight. Provides increased surface area for more positive
sight retention than the small-headed factory screw. Makes
attaching and removing your sight much easier to do, even when
wearing gloves. ab
SPECS: Steel, matte blue. 2 1 ⁄8”(5.3cm) long. Head- .562”(14.2mm)
diameter, 375”(9.5mm) thick.
#100-002-898CG EOTech Replacement Screw,
9A06B85 ..........................$ 6.85
(2) 3 volt CR123A lithium batteries, included. Model 556 is also
compatible with Gen I-III+ night vision systems; 1000:1 night
vision brightness range with NV switch engaged. Model 557
employs a ballistic matched reticle calibrated for the M4 carbine,
with four vertically aligned 1 MOA aiming dots for target distances
of 0-300m, 400m, 500m, and 600m. Fully compatible with
Gen I-IV night vision systems; night vision brightness range of
1000:1 with NV switch engaged. Powered by two (2) common
1.5 volt AA alkaline (included) or lithium batteries; 1,000 hour
continuous battery life with lithium or 600 hours with alkaline.
Requires 3¾" of rail space. 557.3XFTS Sight/Magnifier Combo
contains the Model 557 sight, the 3x Magnifier with FTS mount
(described below), plus a padded, hard-shell carrying case.
SPECS: Polycarbonate body, aluminum hood, matte, black. Lens
- 3 ⁄16" thick, 3-layer, shatterproof laminate glass. 516 & 556 - 51 ⁄8"
(13cm) long, 21 ⁄8" (5.4cm) wide, 2¾” (7cm) high. 11.9 oz. (337g)
weight. Reticle: 1 MOA dot inside a 65 MOA ring. 557 - 5¾”
(14.6cm) long, 21 ⁄8" wide, 2¾” high. 12.3 oz. (349g) weight. Reticle:
four vertically aligned 1 MOA dots.
#100-003-473CG 516 Holographic Sight,
9K455H03 .......................$ 455.03
#100-003-475CG 556 Holographic Sight,
9K573H91 ........................573.91
#100-003-197CG 557 Holographic Sight,
9K553T85 ........................553.85
100-003-988CG 557 Holographic Sight/FTS 3x Magnifier
Combo 9K932V43 ................932.43
MAGNIFIER - Optic system significantly
increases target recognition
capability and accuracy of any EO-
Tech Holographic Weapon Sight
(HWS) out to 600 meters without
compromising CQB effectiveness.
Quick-attach, modular system
mounts on receiver rail right behind
the HWS and requires no adjustments
or modifications to the HWS.
The 3X Magnifier can be attached and removed as needed without
changing point of aim, and the center dot remains 1 M.O.A.
in size, while the angular size of the target is magnified. Included
mount lets you remove the Magnifier and mounting ring quickly
from the mount by simply flipping the side-locking lever. Mount
is fully adjustable for windage and elevation, so the Magnifier
can be adjusted to center the HWS reticle image in the Magnifier’s
window without altering the zero of the sight itself. Steel
cross-bolt and locking bars with large surface area provide solid
attachment to any MIL-STD 1913 Picatinny rail, with sufficient
clearance for most common low-profile flip-up rear sights. Ambidextrous
design lets you position the mount with the release
lever on the left or right side.
SPECS: Aluminum, hardcoat anodized, matte black. Rubber-coated
eyepiece. 1.65” (4.2cm) eye relief. Submersible to 33 ft. Regulates
with any model EOTech Holographic Weapon Sight. 47 ⁄16" (13.8cm)
long, 115 ⁄16" (4.9cm) diameter at widest point. 10.5 oz. (297g) wt.
Actual magnification: 3.25x. Field of view: circular, 6 degrees. Operating
temperature range: -20º to 140º F.
#100-003-037CG FXD 3x Magnifier,
9K399V00 .......................$ 399.00
LASER DEVICES/EOTECH
EOLAD-1V LASER/HOLOGRAPHIC
SIGHT SYSTEM
Dual-Mode System Gives Choice
Of Red Dot Or Laser To Address
Almost Any Target
Advanced dual-mode sighting
system gives the operator the
choice of a holographic red dot sight or a powerful laser sight
to address almost any tactical situation. Combines the fast acquisition,
heads-up versatility, and long-range capabilities of
an EOTech Model 552 holographic sight with the precision of
a powerful 635nm/5mW red laser sight in one compact, flattopmounted
unit. Systems may be operated independently and are
separately adjustable for windage and elevation. Laser has two
output settings and draws power from the 552’s battery pack;
two, included 1.5 volt AA batteries give five hours of continuous
laser operation. Eye-safe low-power setting is for force-on-force
training and CQB; high-power setting for daylight and longdistance
target illumination. Pressure switch on housing activates
laser; a separate plug-in remote switch is provided for use
on handguard or vertical grip. Both switches allow easy tactile
selection of momentary or continuous operation. Master lockout
switch prevents accidental operation and allows selection
of Low or High setting. Removable safety screw prevents accidental
High mode activation. LED on rear of housing indicates
when laser is on and flashes to indicate low battery. Materials
and construction meet MIL-STD-810F for adverse environmental
conditions. Aluminum housing is built to withstand shock,
vibration, and temperature extremes of the harshest law enforcement
and military operations. Aluminum “roll bar” hood
protects display of holographic sight from impact; captive rubber
plug protects laser lens when not in use. Electronics are sealed
against dirt and are waterproof to a depth of 33 feet (10m). Flushmounted,
rubber-sealed, all-weather push-button switches are
built to withstand thousands of on/off cycles. Integral mount
locks securely to Picatinny and Weaver-style rail. 552 sight is
night vision compatible with a brightness range of 1,000:1 with
NV switch engaged. ab
SPECS: Housing/Hood – 6061 T6 aluminum, anodized, matte black.
Polycarbonate battery compartment. 5½” (14cm) long, 2 7 ⁄8" (7.3cm)
wide, 2 3 ⁄8" (6cm) high. 15.8 oz. (448g) weight. Lens - 3 ⁄16" thick,
3-layer, shatterproof laminate glass. Reticle size: 1 MOA dot and
65 MOA ring. Laser – Visible Class IIIa pointer, 5mW power output,
635nm wavelength. 8mm beam diameter at 25m. Maximum laser
range approximately 33 yards (30m) in daylight, 492 yards (450m)
in low light. Uses two AA 1.5 volt alkaline, lithium, or rechargeable
batteries.
#100-003-514CG EOLAD-1V Holographic/Laser Sight,
9A1195D00 ....................$ 1,195.00
brownells.com 43
mounts & optics