Sepam 2000 - Schneider Electric

More documents

Recommendations

Info

CCA 660 connectorb open the 2 side shields for access to theconnection terminals. The shields may be removed, ifnecessary, to facilitate wiring. If removed, replacethem after wiring.b remove the bridging strap, if necessary.The strap links terminals 1, 2 and 3.b connect the wires using 4 mm eye lugs.The connector accommodates wire with crosssectionsof 1.5 to 6 mm 2 (awg 16 to awg 10).b close the side shields.b plug the connector into the 9-pin inlet on the rearof the device. Item B of the ECM module.b tighten the CT connector fastening screwson the rear of Sepam.HV/MV substation Installation - Use - Commissioning1/11
InstallationConnection of current inputs to CSPsThe CSP sensors are connected b prefabricatedcoaxial cables, part no. CCA 601,supplied with Sepam.The cables are plugged into:b Sepam 2000, in the BNC inlets on the rear of thedevice, identified L1, L2 and L3 of the ECA modules,b the CSP sensors, in the BNC outlet on eachsensor,b the 3 BNC outlets are not equippedwith the plugged detector detection system.CSP connection diagramThe CCA 601 cable shielding is earthed naturallyby the connection to Sepam 2000”s BNC inlets.Do not earth by any other means.The CSP sensors should be earthed via thegrounding screw on the side of the device.ECAL1L2L3CCA 601 cableP1P21 2 3ECAL1P1Detailed viewof a connectionCCA 601 cableP2CSP sensor1/12 HV/MV substation Installation - Use - Commissioning
Page 1: Protectionand controlHV/MV substati
Page 5 and 6: InstallationEquipment identificatio
Page 11 and 12: InstallationAssembly and wiring (co
Page 13: InstallationConnection of current i
Page 17 and 18: InstallationUse of CSH 120 and CSH
Page 19 and 20: InstallationUse of the CSH 30 inter
Page 21 and 22: InstallationConnection of voltage i
Page 23 and 24: InstallationConnection of voltage i
Page 25 and 26: InstallationConnection of the Jbus
Page 27 and 28: Use - commissioningDescription / us
Page 29 and 30: Use - commissioningDescription / us
Page 31 and 32: Use - commissioningUse (current ope
Page 33 and 34: Use - commissioningUse (current ope
Page 35 and 36: Use - commissioningCommissioning (c
Page 65 and 66:
Use - commissioningCommissioning (c
Page 67 and 68:
Use - commissioningMaintenanceSepam
Page 69 and 70:
Use - commissioningMaintenance (con
Page 71 and 72:
Sepam 2000 documentationdocumentati
Page 73 and 74:
Commissioning testsTesting a SepamS
Page 75 and 76:
Test sheets - Setting record sheets
Page 77 and 78:
Program logic parametersKP (0 or 1)
Page 79 and 80:
SETTING RECORD SHEETProject: ......
Page 81 and 82:
Sepam 2000 Linefunction identificat
Page 83 and 84:
Status menu parameters (cont’d)me
Page 85 and 86:
Page 87 and 88:
Sepam 2000 HV Busbarsfunction ident
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Sepam 2000 Substationfunction ident
Page 95 and 96:
Page 97 and 98:
Sepam 2000 Capacitorfunction identi
Page 99 and 100:
Page 101 and 102:
Sepam 2000 Overhaed feederfonction
Page 103 and 104:
Page 105 and 106:
3/32 HV/MV substation Installation
show all

Sepam 2000 - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?