Sepam 2000 - Schneider Electric

More documents

Recommendations

Info

MenuEnterP/Select:MeteringProtectionProgram logicEnterP/Select:Add. readingStatusAbout SepamMenuMenu Menu Menu Menu MenuP/ABOUT...SFT 2800Program logicCommunicationP/STATUSRated frequencyPhase CT ratioE/F SensorP/ADD. READINGResidual IResidual VI and V startP/PROGRAM LOGICLogic inputLogic outputMonostable relayP/PROTECTIONOvercurrent/S1 F011Earth fault/S1 F081Thermal F431P/METERINGPhase currentSystem voltagePower & pwr factorEnterEnterEnterEnterEnterEnterMenuMenuMenuMenuMenuMenuP/PROGRAM LOGIC269SFA LDR CATHV/MV SUBSTATIONSUBSTATIONP/PHASE CT RATIOIn = 500 AIb = 450 ANumber = I1-I2-I3P/I RESIDUAL CURRENTI0 = 12.3 AP/LOGIC OUTPUT01-02 = 10011-014 = 0000021-024 = 1010P/OVERCURRENT/S1 F011Curve = DefiniteIs = 1,2 kAT = 300 msP/I PHASE CURRENTI1 = 453 AI2 = 452 AI3 = 453 AMERLIN GERINTSM 2001SelectMeteringProtectionProgram logicmenu784512. 0clear -codedata963units+enterHV/MV substation Installation - Use - Commissioning2/5
Use - commissioningUse (current operation)EnergizingSepam is energized when operating normally.In the event of re-energizing after a break in theauxiliary power supply, Sepam 2000 automaticallyrestarts according to the following sequence, whichlasts about 5 s:b green on and red indicators light up,b beep (if the pocket terminal is connected),b extinction of the red indicator,b setting of the watchdog contact,b testing of display:0,0,0,0,0,0,0,0,0,0,0 then ***********, then I1 = 0.0 A,b breaker position indicator lights up,b display of the first message. Sepam is then in operation.If the pocket terminal is connected, it displays:Pressmenu keyto accessopening menuOperation via the front face or pocket terminal TSM 2001 or the PCfunctions key TSM 2001 menu name description range accuracy commentsphase current A metering I1 measurement of 0 to 24 In +0.5% value depends onI2 each phase current associated CTI3max. demand A metering IM1 measurement of the 0 to 24 In +0.5% the value is periodicallycurrent IM2 average current in recalculated. ValueIM3 the 3 phases set in Status menu to5, 10, 15, 30 or 60 mnRESET: clear keytripping A metering TRIP1 measurement of 0 to 24 In +5% RESET: clear keyTRIP2 phase and earthTRIP3 currents at theTRIP 0 time of tripping 0 to 10 Inovoltage V/Hz metering U21 measurement of 0 to 375 kV +0.5% value depends onU32 system voltages associated VTU13frequency V/Hz metering F measurement of 45 to 65 Hz +0.02 Hz measured onfrequencyU21 inputreal power W/ϕ metering P measurement of 0 to 999 MW +1% positive or negativereal powerreactive power W/ϕ metering Q measurement of 0 to 999 MVAR 1% positive or negativereactive powerpower factor W/ϕ metering COS measurement of -1 to +1 0.01 P sign inductive orpower factorcapacitivepeak demand W/ϕ metering PM measurement of the 0 to 999 MW +1% same comment asreal and reactive greatest average for max. demandpower W/ϕ metering QM power value 0 to 999 MVAR +1% currentsWh/°c metering +MWH measurement of 0 to 99999.99 +1% for displayreal andreal energy consumedreactive Wh/°C metering +MVRH measurement ofenergyreactive energy consumedWh/°C metering -MWH measurement of 0 to 280x10 6 +1% for the pocketreal energy suppliedterminalWh/°C metering -MVRH measurement of values are stored in thereactive energy suppliedevent of a power failureN.B. No value is displayed when the measurement is less than 1.5% of the nominal value.Sepam 2000 performs the functions of a precision measurement and alarmprocessing unit. The values are displayed directed with the related unit A, kA, etc.The messages clearly worded. There are two ways of operating the device:b via the front face (metering, annunciation keys),b via the TSM 2001 pocket terminals or PC (using menu).Whenever a measurement is not available in the user’s type of Sepam----------- is displayed.2/6 HV/MV substation Installation - Use - Commissioning
Page 1: Protectionand controlHV/MV substati
Page 5 and 6: InstallationEquipment identificatio
Page 11 and 12: InstallationAssembly and wiring (co
Page 13 and 14: InstallationConnection of current i
Page 15 and 16: InstallationConnection of current i
Page 17 and 18: InstallationUse of CSH 120 and CSH
Page 19 and 20: InstallationUse of the CSH 30 inter
Page 21 and 22: InstallationConnection of voltage i
Page 23 and 24: InstallationConnection of voltage i
Page 25 and 26: InstallationConnection of the Jbus
Page 27 and 28: Use - commissioningDescription / us
Page 29: Use - commissioningDescription / us
Page 33 and 34: Use - commissioningUse (current ope
Page 35 and 36: Use - commissioningCommissioning (c
Page 67 and 68: Use - commissioningMaintenanceSepam
Page 69 and 70: Use - commissioningMaintenance (con
Page 71 and 72: Sepam 2000 documentationdocumentati
Page 73 and 74: Commissioning testsTesting a SepamS
Page 75 and 76: Test sheets - Setting record sheets
Page 77 and 78: Program logic parametersKP (0 or 1)
Page 79 and 80: SETTING RECORD SHEETProject: ......
Page 81 and 82:
Sepam 2000 Linefunction identificat
Page 83 and 84:
Status menu parameters (cont’d)me
Page 85 and 86:
SETTING RECORD SHEETProject: ......
Page 87 and 88:
Sepam 2000 HV Busbarsfunction ident
Page 89 and 90:
Page 91 and 92:
SETTING RECORD SHEETProject: ......
Page 93 and 94:
Sepam 2000 Substationfunction ident
Page 95 and 96:
Page 97 and 98:
Sepam 2000 Capacitorfunction identi
Page 99 and 100:
Page 101 and 102:
Sepam 2000 Overhaed feederfonction
Page 103 and 104:
Page 105 and 106:
3/32 HV/MV substation Installation
show all

Sepam 2000 - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?