Wadkin ECA Tenoner Manual and Parts List

More documents

Recommendations

Info

METHOD OF DISMANTLING TENON HEAD SPINDLE ASSEMBLY TOREAR BEARING1. Remove end cap EKA 48.2.. Remove locknut No. 2B or 2A.3. Remove brake drum EC 80.4. Remove brake housing EKA 47.5. Remove bearing housing EC 55 or EC 56 and bearing.6. Knock out bearing and fit replacement SKF 2206 bearing.7. To reassemble, reverse dismantling operation.MIDDLE BEARING8. Repeat operations 1, 2, 3, 4, 5.9. Remove locknut WA 498 or WA 487 and cuUerblock EC 182.10. Remove plate EH 29.11. Remove grease retainer EC 79.12. Remove stator frame EC 57 complete with Stator.13. Remove end cover EC 11.14. Remove locknut EC 132 or EC 133.15. Withdraw shaft EC 49 or EC 50 from rear end.16. Remove rotor from shaft.17. Loosen countersunk screw and remove locknut No. 7 A and 7B.18. Remove grease retainer EH 65.19. Remove bearing and fit replacement SKF 2209 bearing.20. To reassemble, reverse dismantling operations.~I~\~:'G/:FRONT BEARINGNEW BEARINGS.21. Repeat operations 1, 2, 3, 4, 5, 9, 10, 11, 12,13, 14, 15.22. Knock out bearing from EH or EH 17/ Aand fit replacement SKF 2208 bearing.23. To reassemble, reverse dismantlingTO REMOVE STATOR FROM FRAMERemove B. S. P. Pipscrew 'M' from frameand knock out stator.IMPORTANTWhen replacing stator, care must be taken to avoiddrilling into the winding". Maximum depth of pipscrewhole is to the tip of the drill.BOTTOM TENON SPINDLE E. C. 50Thread 'N' l"fine thread 14 T.P.I. R.H.Thread 'P' HI! fine thread 14 T. P. 1. R. H.Thread 'Q' It" fine thread 14 T. P. 1. L. H.Thread 'R' ti" fine thread 14 T.P.I. L.H.TOP TENON SPINDLE E. C. 49Thread 'N' 1"fine thread 14 T.P.I. L.H.Thread 'P' H" fine thread 14 T. P. 1. L. H.Thread 'Q' It" fine thread 14 T. P. 1. R. H.Thread 'R' It" fine thread 14 T.P.I. R.H.www.wadkin.cominfo@wadkin.comPage 13.
CUT-OFF SAW SPINDLE ASSEMBLY.METHOD OF DISMANTLING TO FIT NEWBEARINGS,REAR BEARING.1. Remove cap 'A', Fig.122. Loosen countersunk screw and removelocknut 'B'.3. Remove bearing housing' C'.4. Knock out bearing from housing and fitreplacement.5. To reassemble reverse dismantling operation.FRONT BEARING.6. Remove locknut 'D', collar 'E I,saw and collar IF'.7. Remove end cap 'G'.8. Repeat operations 1, 2 and 3.9. Withdraw spindle from sawend of frame 'HI.10. Knock out taper pin andremove collar' JI.11. Remove rotor from shaft.12. Loosen countersunk screw andremove locknut 'K'.13. Remove grease retainer 'LI.14. Remove bearing from shaftand fit replacement.15. To reassemble reverse dismantlingoperation.QTO REMOVE STATOR FROM FRAME.Remove t" B. S. P. Pipscrew 'M' from frameand knock out stator.IMPORTANT.When replacing stator care must be taken toavoid drilling into the windings.Maximum depth of pipscrew hole is 5/16" to thetip of the drill.CUT OFF SAW SPINDLE E. H. 92.Thread 'N' 1" fine thread 14 T. P. I. R. H.Thread 'P' li" fine thread 14 T. P. I. L. H.Thread 'Q' 1" fine thread 14 T. P. I. L. H.www.wadkin.cominfo@wadkin.comCUT - OFF SAW SPINDLE. ASSE.MBLY. FIG. 12.Page 15
Page 1 and 2: LUBRICATIONLubrication point Con le
Page 5: HEADSTOCKADJUSTMENTS.TOP TENONING H
Page 10 and 11: MOULDING ONCUTTERTENON SPINDLE.a 4.
Page 12 and 13: 11I1LT 1 -:":-::-::-~-~-~-~T~I ~_..
Page 14 and 15: TENON BLOCK ADZE CUTTER GRINDING AT
Page 16 and 17: CUTTER GRINDINGFIG. 2TUNGSTEN CARBI
Page 18 and 19: low away harmful dust,hi s and di t
Page 20 and 21: ELECTRICAL INSTALLATION INSTRUCTION
Page 22 and 23: TENON BLOCK ADZE CUTTER GRINDING AT
Page 24 and 25: CUTTEREQUIPMENTINSERTED TOOTH GROOV
Page 26 and 27: CUTTEREQUIPMENTTRENCHING AND GROOVI
Page 28 and 29: SCRIBING OR COPE SPINDLE ASSEMBLYME
Page 30 and 31: THE TABLE.The table is mounted on f
Page 32 and 33: A ______________ __EBuHoHand brakes
Page 34 and 35: SPARE PMTS BOOKLET/, :~--- -'/'.CON
Page 36 and 37: SAMPLE TYPE ORDERMACHINE:ECAMACHINE
Page 38 and 39: EC250/EC79EC250/EC80EC250/EC8lEC250
Page 40 and 41: EC250/EH122EC250/EH123EC250/EH126VE
Page 42 and 43: EC250/7AEC250/7BEC250/11AEC250/62EC
Page 44: '.,,'""== f"'I~.. ~\!V-~~~DII¥I.I

Wadkin ECA Tenoner Manual and Parts List

Create successful ePaper yourself

Delete template?

Save as template?