MSA_Firehawk_M7_Mask.. - SOLD

More documents

Recommendations

Info

FIREHAWK M7 TELEMETRY MODULEit will log on to the first base station that it finds once theunit has been turned on. Once a base station ID tag hasbeen scanned into the FireHawk M7 Control Module, thisbase station ID will remain with the air mask until anotherbase station ID tag has been scanned.The ID Tag has a space for the user to place a label inwhich the ID information can be written on the outside ofthe ID Tag for easy identification.Before using the ID tag, inspect for damage or cracks inthe case. If damage is found, discard and replace the IDtag.Scanning the ID Tag into the FireHawk M7 ControlModuleNote: The FireHawk M7 Control Module must be turnedoff to scan the ID Tag.Prior to pressurization ofthe air mask and duringinspection, the user can“tag in” by depressing andholding the top mode button(green) until the word“tag” appears in the display.While “tag” is displayed,hold the ID tag asshown.Correct ID Tag OrientationThe FireHawk M7 Control Module will display "ok" whenthe ID Tag has been successfully read and the unit willautomatically return to sleep mode. If the word "data"appears on the Firehawk M7 Control Module display beforethe ID Tag has been successfully read, push the mode buttononce to skip "data" mode and return to sleep mode.Press and hold the mode button to return to "tag" mode.The "data" mode is used to change the device settings orread the data log while using the M7 Interface Software.The "data" mode can be entered directly by pressing theholding the mode button until "tag" is displayed. While"tag" is displayed, an additional push of the mode buttonwill toggle the device into "data" mode.The most recent ID Tag data that is stored in the FireHawkM7 Control Module will be used as the identification forthe air mask on the MSA Accountability System Software.If no ID Tag data has been assigned to the air mask, theFireHawk M7 Control Module serial number will be usedas its identification on the base station PC screen.The ID tag is not designed to be taken into a fire. TheID tag can also be used as an accountability tag.Using the Base Station with the FireHawk M7Telemetry ModuleThe FireHawk M7 Telemetry Module is designed to workin conjunction with a remote base station unit. This basestation unit must be connected to a personal computer orlaptop before use. Refer to the MSA AccountabilitySystem Software instructions (PN 10068929) for moreinformation.Follow the PC or notebook computer manufacturer’srecommendations for exposure to environmental conditionsto prevent damage to the system. Failure to doso may cause system failure and the loss of monitoringcapability on the PC or notebook computer.Using the M7 Firehawk Air Mask with FireHawk M7Telemetry ModuleLogging the Air Mask on to the Base Station1. Turn on the FireHawk M7 Control Module on by openingthe cylinder valve or by pressing and holding thealarm button.2. A helmet icon representing the user of the air maskwill appear on the base station PC screen.3. When the base station has established contact with theair mask and all initial information has been obtained,the radio link indicator will appear in the upper left cornerof the FireHawk M7 Control Module display.4. Periodically check the status of the radio link indicatoron the display of the FireHawk M7 Control Module. Ifthe signal strength indicator begins to flash, thismeans that the air mask is out of range from the basestation. The signal strength indicator will stop flashingwhen the air mask returns within range of the basestation.If the signal strength indicator does not appear on theFireHawk M7 Control Module display, the base stationhas not logged the unit on and can not monitor thestatus of that firefighter.Logging the Air Mask off of the Base Station1. Once the user has returned to fresh air the FireHawkM7 Control Module may be turned off.2. Close the cylinder valve and purge the remaining airfrom the system using the Firehawk Regulator bypass.When the pressure falls below 200 psi, turn theFireHawk M7 Control Module off (sleep mode) bypressing the reset button twice in approximately onesecond. (When the air mask is logged on to a basestation, there may be a delay between the two rapidpresses of the reset button and the actual shutdownTAL 806 (L) Rev. 3 - 1008285844
FIREHAWK M7 TELEMETRY MODULEof the FireHawk M7 Control Module. Before theFireHawk M7 Control Module completely turns off, thebase station must log off the air mask and send out afinal confirmation signal.Evacuation SignalIf the air mask is logged on to the base station, the incidentcommand will have the ability to send an evacuationsignal to the air mask. When an evacuation signal is sentto the air mask, the FireHawk M7 Power Module will beginto beep repeatedly and a flashing “running man” icon willappear on the FireHawk M7 Control Module display. Theevacuation alarm will continue to sound until the resetbutton on the FireHawk M7 Control Module has beenpressed twice within approximately one second. This confirmsthe evacuation by sending a confirmation signalback to the base station.45 TAL 806 (L) Rev. 3 - 10082858
Page 1 and 2: FireHawk ® M7Air MaskNFPA 1981: 20
Page 3 and 4: INTRODUCTIONDo not mark the air mas
Page 5: DESCRIPTIONDESCRIPTIONFireHawk M7 A
Page 8 and 9: NOTESTAL 806 (L) Rev. 3 - 100828588
Page 10 and 11: VISUAL INSPECTION AND FUNCTIONAL TE
Page 12 and 13: VISUAL INSPECTION AND FUNCTIONAL TE
Page 14 and 15: DONNINGDONNING THE FACEPIECE7. Chec
Page 16 and 17: DONNING1. Grasp and orient theregul
Page 18: USING THE AIR MASKred when the air
Page 21 and 22: USING THE AIR MASKo Red LEDs flash
Page 23 and 24: USING THE AIR MASK5. Install the ba
Page 25 and 26: AUDI-LARM ALARM WITH URC ASSEMBLYUR
Page 27 and 28: AUDI-LARM ALARM WITH URC ASSEMBLYTh
Page 29 and 30: REMOVING THE AIR MASKDISCONNECTING
Page 31 and 32: REMOVING THE AIR MASKto a brown or
Page 33 and 34: CLEANING AND DISINFECTINGCLEANING A
Page 35 and 36: FLOW TEST AND OVERHAUL REQUIREMENTS
Page 37 and 38: QUICK-FILL SYSTEMPRECAUTIONS FOR US
Page 39 and 40: QUICK-FILL SYSTEMwill drop, and the
Page 41 and 42: EXTENDAIRE SYSTEMINSTRUCTIONS FOR U
Page 43: FIREHAWK M7 TELEMETRY MODULEFIREHAW
Page 47: NOTES47 TAL 806 (L) Rev. 3 - 100828

MSA_Firehawk_M7_Mask.. - SOLD

Create successful ePaper yourself

Delete template?

Save as template?