MiniSteam Instruction Manual - HygroMatik

More documents

Recommendations

Info

2214828641112381014151622211758223926492220222422222218193530313242434425Please also see Section „Exploded View“.37Location Designation1 steam nozzle6 vent pipe10 max. water level sensor electrode14 water drain, discharge16 top part of steam cylinder17 o-ring cylinder flange18 cylinder flange and o-ring19 lower part of cylinder25 solenoid valve water inlet32 blow-down pump35 o-ring37 cylinder base48 electrodesPage 12
The concentration of dissolved salts increases over time, whichcan lead to a rise in the conductivity of the water. If this continues,conductivity may increase until a short circuit occurs. Thiscould damage the unit, but in any case would significantlyreduce the life span of the electrodes.For this reason, regular, periodic blow-downs of some of theconcentrated water are very important. Following this procedureas recommended provides stable cylinder water conductivity aswell as minimal water loss for the expected service life of the cylinder.Water blow-down is performed by a blow-down pump (32). Thefunctioning of the blow-down pump is continuously monitoredduring operation. If the pump is damaged, the steam humidifiershuts down.With normal water quality, the blow-down loss rate is between7% and 15% of the amount of steam produced. The steam cylinderrequires complete drainage every 3-8 days, regardless ofthe water quality.Mineral deposits settle in the open area below the electrodesand are removed through periodic maintenance. The blow-downpump itself has wide openings and can flush out smaller piecesof mineral deposit. This extends the service life of the unit andreduces the required maintenance interval.During blow-downs, water flows from the pump into the drainagesystem.A sensor electrode (10) monitors the maximum water capacityof the cylinder. When the water level reaches the sensor electrode,the water supply is interrupted. This can occur when thewater has low conductivity or when the electrodes are worn out.In the case of low water conductivity, however, this state usuallylasts only a short time. The built-in control and the large areaelectrodes combine to produce a rapid rise in conductivity byincreasing the concentration of the water.Page 13
Page 1 and 2: ManualElectrode Steam HumidifierMin
Page 3 and 4: 1. Introduction ...................
Page 5 and 6: 1. IntroductionDear Customer,Thank
Page 7 and 8: 2. Safety Notes2.1 OverviewThese sa
Page 9 and 10: 3. Transport3.1 OverviewNote: Proce
Page 11: 4. Operation and Installation4.1 Mo
Page 15 and 16: 5. InstallationWarning: Installatio
Page 17 and 18: Wall MountingNote: The steam humidi
Page 19 and 20: 6. Water InstallationWarning: When
Page 21 and 22: » Use a cap nut (internal thread
Page 23 and 24: 7. Electrical ConnectionDanger, Haz
Page 25 and 26: MiniSteam:Type Power Usage Circuit
Page 27 and 28: 8. MaintenanceThe HygroMatik steam
Page 29 and 30: » The basic PCB (C) is now accessa
Page 31 and 32: » then:CleaningWarning: Check the
Page 33 and 34: » Push in safety fuses.Switch on t
Page 35 and 36: » Remove cylinder, as described in
Page 37 and 38: » Place solenoid valve with seal i
Page 39 and 40: 10. EC-Declaration of ConformityPag
Page 41 and 42: * MS5 MS10 Article no. DescriptionW
Page 43 and 44: 13. Technical DataTechnical Data St
Page 45 and 46: 15. View of housingPage 45

MiniSteam Instruction Manual - HygroMatik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?