This manual must be read thoroughly and always - esco ...

More documents

Recommendations

Info

Product Manual escostart DS3 47 3H – Stop Mode-2 3I – Stop Time-2 3J – Adptv Start Prof-2 3K – Adptv Stop Prof-2 3L – Adptv Ctrl Gain-2 Options: Coast to Stop (Default) TVR Soft Stop Adaptive Control Brake Description: Selects the stop mode. Range: 0:00 - 4:00 (minutes:seconds) Default: 0 seconds Description: Sets the stop time. Options: Early Acceleration Constant Acceleration (Default) Late Acceleration Description: Selects which profile the escostart DS3 will use for an AAC Adaptive Acceleration Control soft start. Options: Early Deceleration Constant Deceleration (Default) Late Deceleration Description: Selects which profile the escostart DS3 will use for an AAC Adaptive Deceleration Control soft stop. Range: 1% - 200% Default: 75% Description: Adjusts the performance of AAC Adaptive Control. This setting affects both starting and stopping control. Product Manual escostart DS3 47
48 Product Manual escostart DS3 8.1.4 Protection Levels 4A – Current Imbalance 4B – Phase Sequence 4C – Undercurrent 4D – Instantaneous Overcurrent 4E – Input A Trip Range: 10% - 50% Default: 30% Description: Sets the trip point for current imbalance protection. Range: Any sequence (Default) Positive only Negative only Description: Selects which phase sequences the soft starter will allow at a start. During its pre-start checks, the starter examines the sequence of the phases at its input terminals and trips if the actual sequence does not match the selected option. Range: 0% - 100% Default: 20% Description: Sets the trip point for undercurrent protection, as a percentage of motor full load current. Set to a level between the motor's normal working range and the motor's magnetising (no load) current (typically 25% to 35% of full load current). A setting of 0% disables undercurrent protection. Range: 80% - 600% FLC Default: 400% Description: Sets the trip point for instantaneous overcurrent protection, as a percentage of motor full load current. Options: Always Active (Default) A trip can occur at any time when the soft starter is receiving power. 4F – Motor Temp Check Operating Only A trip can occur while the soft starter is running, stopping or starting. Run Only A trip can only occur while the soft starter is running. Description: Selects when an input trip can occur. Range: Do Not Check (Default) Check Description: Selects whether the escostart DS3 will verify the motor has sufficient thermal capacity for a successful start. The soft starter compares the motor's calculated temperature with the temperature rise from the last motor start and only operates if the motor is cool enough to start successfully. 48 Product Manual escostart DS3
Page 1 and 2: This manual must be read thoroughly
Page 3 and 4: 2 Product Manual escostart DS3 9. A
Page 5 and 6: 4 Product Manual escostart DS3 2. D
Page 7 and 8: 6 Product Manual escostart DS3 3.2.
Page 9 and 10: 8 Product Manual escostart DS3 Curr
Page 11 and 12: 10 Product Manual escostart DS3 3.2
Page 13 and 14: 12 Product Manual escostart DS3 Hea
Page 27 and 28: 26 Product Manual escostart DS3 6.
Page 29 and 30: 28 Product Manual escostart DS3 Dat
Page 35 and 36: 34 Product Manual escostart DS3 NOT
Page 39 and 40: 38 Product Manual escostart DS3 App
Page 43 and 44: 42 Product Manual escostart DS3 Def
Page 47: 46 Product Manual escostart DS3 8.1
Page 51 and 52: 50 Product Manual escostart DS3 5F
Page 53 and 54: 52 Product Manual escostart DS3 6D
Page 55 and 56: 54 Product Manual escostart DS3 7J,
Page 57 and 58: 56 Product Manual escostart DS3 9B
Page 61 and 62: 60 Product Manual escostart DS3 15I
Page 73 and 74: 72 Product Manual escostart DS3 Par
Page 75 and 76: 74 Product Manual escostart DS3 Dis
Page 81 and 82: 80 Product Manual escostart DS3 086

This manual must be read thoroughly and always - esco ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?