2000 Series Articulator and QuickMount Face-Bow ... - Whip Mix

More documents

Recommendations

Info

Fig. 68Position the #8686 Support Bar onto the top of theTransfer Assembly and secure in place with the same#8604 Locking Screw.Remove the upper frame of the articulator from the lowerframe and then remove the incisal guide pin.Fig. 69Place the transfer base assembly on the lower member ofthe articulator and secure it using the magnetic face-bowfork support.Set the condylar inclination to the “FB” marking on eachcondylar inclination scale for articulators with immediateside shift. Set the condylar inclination to 30° for modelswith progressive side shift. Next, set the immediate orprogressive side shift guides to “0”.II. Placing the Face-Bow TransferAssembly on the ArticulatorFig. 70Insert the vertical rod of the transfer assembly into thetransfer base and lower it until the bottom of the vertical rodcontacts the transfer base. Tighten the #9184 Clamp Screwso that the vertical rod fits securely in the Transfer Base.Fig. 71Place the upper frame of the articulator onto the lowerframe so the front of the upper frame now rests on the#8686 Support Bar and place a QuickMount MagneticPlate on the upper frame.24
Fig. 72Raise the face-bow fork support until it touches theunder-surface of the face-bow fork.Fig. 73Engage the centric latch or spring latch on the articulator tokeep the condyles in contact with the posterior and superiorwalls of the condylar guides.III. Mounting the Maxillary CastFig. 74Position the upper cast into the bite registration.Fig. 75Apply Whip Mix MOUNTING STONE to the upper mountingplate and the top of the upper cast and carefully hinge theupper frame so that it contacts the top of the #8686Support Bar.When the stone has set, remove the upper frame to allowremoval of the transfer assembly and transfer base.Replacethe incisal guide pin in the upper frame and re-attach tolower frame. Also, replace the mounting plate on the lowerframe and proceed with the mounting of the lower cast asdescribed in the Articulator Instruction Manual.25
Page 1 and 2: 2000 SeriesArticulatorandQuickMount
Page 3 and 4: CONTENTSINTRODUCTION 5OBTAINING FAC
Page 5 and 6: INTRODUCTIONThe WHIP MIX Articulato
Page 7 and 8: Fig. 5Loosen the #8604 thumb screw
Page 9 and 10: III. Positioning Face-Bow on the Pa
Page 11 and 12: Fig. 21To prevent torquing of the f
Page 13 and 14: Centric Relation RecordFig. 27Many
Page 15 and 16: Lateral Interocclusal RecordsFig. 3
Page 17 and 18: Fig. 41Loosen the #8511 incisal gui
Page 19 and 20: II. Placing a Direct Mounting Face-
Page 21 and 22: Fig. 57Engage the centric latch for
Page 23: INDIRECT MOUNTING THE MAXILLARY CAS
Page 27 and 28: Fig 80If using the Model 2340 Artic
Page 29 and 30: Fig. 87Prepare a second mix to fill
Page 31 and 32: Fig. 93If using the Model 2340 Arti
Page 33 and 34: Fig. 101If using the Model 2340 Art
Page 35 and 36: SETTING THE CONDYLAR GUIDANCE OF TH
Page 37 and 38: Fig. 113Lubricate the rounded end o
Page 39 and 40: Fig. 120Move through all intermedia
Page 41: III. Preparing Face-Bow Armamentari
Page 44 and 45: Fig. 138The QUICKMOUNT transfer bas
Page 46 and 47: Fig. 146Adjust the inclination of t
Page 48 and 49: XII. Remounting CastsFig. 154After
Page 50 and 51: Transfer Of Casts To Another Articu
Page 52 and 53: Reminders And Suggestions1. When se
Page 54 and 55: 2000 SERIES ARTICULATOR PARTS LISTS
Page 56 and 57: WHIP MIX FACE-BOW PARTS LISTSModel
Page 58 and 59: MODELS 9175/9185/9195FACE-BOWSFOR I
Page 60 and 61: BibliographyThe following bibliogra
Page 62 and 63: NOTES______________________________
Page 64: For additional information, contact

2000 Series Articulator and QuickMount Face-Bow ... - Whip Mix

Create successful ePaper yourself

Delete template?

Save as template?