User manual - teles

More documents

Recommendations

Info

VIERLING 2.2.5 Installing the configuration software » Insert the supplied CD-ROM ECOTEL ® VoIP/ISDN2-1/ISDN2-2 into your computer. » In the \Software directory, run the Setup.exe program. » Follow the installation instructions on the screen. The ECOTEL Service Gear configuration software will now be installed. Once it is ready, you can launch it via Start > Programs > ECOTEL Service Gear. If necessary, you should now get an initial overview of the design and operation of the configuration software. 4 Usage of the configuration software The following sections describe the steps needed to quickly get ECOTEL ® up and running. Page 24 Edition 4.1-EN – 20070730 ECOTEL ® VoIP/ISDN2-1/ISDN2-2
2.2.6 Configuration steps in Service Gear » Launch the configuration software: Start – Programs – ECOTEL Service Gear (The Service Gear module should appear.) » Create a new group: Mark the Devices tree node Edit > Add Group. Give the group a name of your choice. OK VIERLING » Create ECOTEL ® as a new device: Mark a group Edit > Add Device. (The Properties dialog for the new device should appear.) » Edit the properties: Give your device a Name of your choice. Select the Device Type. Under Access Via: Choose the interface you wish to use to configure the device. Fill in the remaining fields (depending on the means of access). Leave the Security Code field blank (factory default) OK Information about initial access: When it is shipped, ECOTEL ® has the following default settings: IP address for configuration: 192.168.10.10, subnet mask: 255.255.255.0. If you wish to access your ECOTEL ® in this state via IP, your computer will need a suitable IP address, e.g. in the format 192.168.10.xx. If you want to access ECOTEL ® via a different IP address, use the USB or RS232 interface to access it for the first time and then change the default IP settings in ECOTEL ® . 2.2.8 Configuration steps in Basic Configuration ECOTEL ® VoIP/ISDN2-1/ISDN2-2 Edition 4.1-EN – 20070730 Page 25
Page 1 and 2: ECOTEL ® VoIP ECOTEL ® ISDN2-1 EC
Page 3 and 4: Content VIERLING 1 Introduction....
Page 5 and 6: VIERLING 5 Introduction to the rout
Page 7 and 8: VIERLING 6.5.4 Firmware Tools: Firm
Page 9 and 10: VIERLING 9.7 Special notes about EC
Page 11 and 12: 1.1 Overview: Please read this firs
Page 13 and 14: 1.2 Safety instructions VIERLING Th
Page 15 and 16: Repairs VIERLING Repairs must be pe
Page 17 and 18: 2 Getting started VIERLING ECOTEL
Page 19 and 20: 2.2 Installation guideline VIERLING
Page 21 and 22: 2.2.3 Connecting the device VIERLIN
Page 23: VIERLING » Open Windows device man
Page 27 and 28: VIERLING 2.2.7 Configuration steps
Page 29 and 30: VIERLING 2.2.8 Configuration steps
Page 31 and 32: 2.2.9 Configuration steps in User R
Page 33 and 34: 2.2.10 Configuration steps in Routi
Page 35 and 36: VIERLING » Repeat these steps for
Page 37 and 38: 2.2.13 Checking for proper operatio
Page 39 and 40: 3 Operating modes VIERLING ECOTEL
Page 41 and 42: Overview of possible ISDN configura
Page 43 and 44: VIERLING Note: The choice of whethe
Page 45 and 46: ISDN configuration: VIERLING BRI1 B
Page 59 and 60: ISDN configuration: BRI1 BRI2 (100
Page 61 and 62: ISDN configuration, variant 1: As i
Page 63 and 64: 3.3.2 Call routing via the VoIP por
Page 65 and 66: ISDN configuration: As in the follo
Page 67 and 68: 3.3.5 Box-to-box operation VIERLING
Page 69 and 70: VIERLING 3.4.2 Call hold switching
Page 71 and 72: VIERLING 3.4.4 SIP outbounds (SIP p
Page 73 and 74: 3.4.5 SIM management VIERLING Note:
Page 75 and 76:
VIERLING 4 Calling number = Number
Page 77 and 78:
3.4.7 Automatic call forwarding Not
Page 79 and 80:
3.4.8 Callback request via SMS VIER
Page 81 and 82:
VIERLING 4 Usage of the configurati
Page 83 and 84:
File management VIERLING There are
Page 85 and 86:
VIERLING via GSM to the devices whi
Page 87 and 88:
SIM Management (not for ECOTEL ® I
Page 89 and 90:
VIERLING 4.3.1 Connecting via IP (L
Page 91 and 92:
4.3.2 Connecting via modem VIERLING
Page 93 and 94:
Setting up the device » In the Ser
Page 95 and 96:
4.4 Editing the configuration files
Page 97 and 98:
4.5 Generating traces VIERLING Trac
Page 99 and 100:
VIERLING » Click on Save Trace. Se
Page 101 and 102:
5 Introduction to the routing table
Page 103 and 104:
VIERLING unchanged, parts of it can
Page 105 and 106:
5.3 Strategy for the routing table
Page 107 and 108:
5.4 Outgoing calls VIERLING The rou
Page 109 and 110:
Example 3: VIERLING Dial the phone
Page 111 and 112:
Example 8: Invalid entry Dial the p
Page 113 and 114:
Example 5: VIERLING When using spee
Page 115 and 116:
5.4.4 Calls to an arbitrary extensi
Page 117 and 118:
5.5 Incoming calls VIERLING The rou
Page 119 and 120:
Example 3: VIERLING When called by
Page 121 and 122:
5.5.2 Calls to a specified MSN Exam
Page 123 and 124:
5.6.1 Routing based on the interfac
Page 125 and 126:
5.6.2 B-channel routing VIERLING By
Page 127 and 128:
5.6.4 Routing to a specific GSM net
Page 129 and 130:
5.8 Date- and time-dependent routin
Page 131 and 132:
Example 4: VIERLING The routing ent
Page 133 and 134:
5.9.1 Dialing callback with disconn
Page 135 and 136:
5.9.2 Dialing callback without disc
Page 137 and 138:
5.9.4 Non-dialing callback without
Page 139 and 140:
5.11 Default configuration VIERLING
Page 141 and 142:
5.12 User scenario VIERLING A typic
Page 143 and 144:
VIERLING 6 Reference: Operating ele
Page 145 and 146:
6.2 Service Gear module VIERLING Th
Page 147 and 148:
6.2.1 Service Gear: Main window VIE
Page 149 and 150:
6.2.2 Service Gear: Properties Grou
Page 151 and 152:
VIERLING IP address IP address of t
Page 153 and 154:
6.2.4 Service Gear: Properties Mode
Page 155 and 156:
6.3 Gateway Configuration module VI
Page 157 and 158:
New... Open… Save VIERLING Opens
Page 159 and 160:
6.3.2 Gateway Configuration: Proper
Page 161 and 162:
6.3.3 Gateway Configuration: BRI 1/
Page 163 and 164:
When end of dialing is reached, sta
Page 165 and 166:
Keep in the list the entries of An
Page 167 and 168:
Change bearer capability of GSM cal
Page 169 and 170:
VIERLING 6.3.8 Gateway Configuratio
Page 171 and 172:
Overall calltime limit Use limit of
Page 173 and 174:
VIERLING 6.3.10 Gateway Configurati
Page 175 and 176:
VIERLING The CLIR also be used sele
Page 177 and 178:
Page 179 and 180:
6.3.13 Gateway Configuration: SIP I
Page 181 and 182:
Page 183 and 184:
Outbound device (1st line: Domain d
Page 185 and 186:
VIERLING With username The user nam
Page 187 and 188:
6.3.17 Gateway Configuration: Devic
Page 189 and 190:
6.4.1 Routing Table: Main window VI
Page 191 and 192:
6.4.2 Routing Table: Routing VIERLI
Page 193 and 194:
6.4.3 The routing syntax VIERLING T
Page 195 and 196:
VIERLING Indication of the permiss
Page 197 and 198:
VIERLING G{} The call is set up via
Page 199 and 200:
6.4.4 The Routing Wizard VIERLING C
Page 201 and 202:
VIERLING (selected port) The origin
Page 203 and 204:
VIERLING Note: You can also just do
Page 205 and 206:
6.4.5 Routing Table: Remote Connect
Page 207 and 208:
6.5.1 Firmware Tools: Main window V
Page 209 and 210:
6.5.3 Firmware Tools: Security Code
Page 211 and 212:
6.5.4 Firmware Tools: Firmware Down
Page 213 and 214:
VIERLING A list of the WAVE files w
Page 215 and 216:
Delete Transferred Files Upload fro
Page 217 and 218:
VIERLING Warning: Always modify thi
Page 219 and 220:
VIERLING Delete Deletes the selecte
Page 221 and 222:
Long-Term Traces Opens the Long-Ter
Page 223 and 224:
6.5.10 Firmware Tools: Remote Conne
Page 225 and 226:
6.6 Basic Configuration module VIER
Page 227 and 228:
6.6.2 Basic Configuration: ISDN Int
Page 229 and 230:
6.6.3 Basic Configuration: IP Conne
Page 231 and 232:
Domain name (preferred) VIERLING Th
Page 233 and 234:
6.7 Monitor module Note: This modul
Page 235 and 236:
6.7.2 Monitor: Channels VIERLING Ca
Page 237 and 238:
VIERLING Avg duration [s] Average c
Page 239 and 240:
Remove released connections after V
Page 241 and 242:
Display options h:mm:ss m:ss s VIER
Page 243 and 244:
Groups of SIM cards VIERLING The SI
Page 245 and 246:
6.8.2 SIM Management: SIM Cardholde
Page 247 and 248:
Clock model in seconds Lock to pref
Page 249 and 250:
VIERLING 6.8.4 SIM Management: GSM
Page 251 and 252:
6.8.5 SIM Management: Device VIERLI
Page 253 and 254:
6.9.1 User Registration: Main windo
Page 255 and 256:
VIERLING Edit... Opens the User Reg
Page 257 and 258:
6.10.1 IO Configuration: Main windo
Page 259 and 260:
6.10.3 IO Configuration: IO Channel
Page 261 and 262:
Send SMS if signal is... VIERLING a
Page 263 and 264:
6.10.4 IO Configuration: Device VIE
Page 265 and 266:
7.1 Overview: What ECOTEL users mus
Page 267 and 268:
VIERLING For all other applications
Page 269 and 270:
7.2.3 Setting up fixed connections
Page 271 and 272:
7.3.2 Routing calls to a fixed exte
Page 273 and 274:
7.3.4 Call forwarding VIERLING Duri
Page 275 and 276:
Switching between the different cal
Page 277 and 278:
8 Additional topics and background
Page 279 and 280:
8.2 Interpretation of the interface
Page 281 and 282:
Modem VIERLING In everyday terms, t
Page 283 and 284:
8.4 General information about VoIP
Page 285 and 286:
VIERLING UAC. As a general rule, in
Page 287 and 288:
8.4.2 Codec VIERLING A codec (COmpr
Page 289 and 290:
9 Special hardware-related issues V
Page 291 and 292:
BRI 1 Off ISDN port 1 is deactivate
Page 293 and 294:
9.1.2 Display elements on the housi
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
9.2 Interfaces on the housing VIERL
Page 301 and 302:
I/O VIERLING RJ-45 jack with six in
Page 303 and 304:
9.3 Interfaces BRI1, BRI2 VIERLING
Page 305 and 306:
9.3.1 BRI1 connection VIERLING In t
Page 307 and 308:
9.4 Antennas VIERLING Depending on
Page 309 and 310:
SIM cardholders VIERLING Note: This
Page 311 and 312:
9.5.1 SIM8 cardholder VIERLING The
Page 313 and 314:
VIERLING ECOTEL ® VoIP/ISDN2-1/ISD
Page 315 and 316:
9.5.4 SIM emulation board VIERLING
Page 317 and 318:
Wiring the BRI interfaces VIERLING
Page 319 and 320:
10 Technical Details VIERLING ECOTE
Page 321 and 322:
Tones SYS016a.wav Sinewave 425 Hz D
Page 323 and 324:
10.2 Package contents 10.2.1 Packag
Page 325 and 326:
10.2.3 Package contents ECOTEL ISDN
Page 327 and 328:
VIERLING 10.3.2 Spare parts / Acces
Page 329 and 330:
10.4 Specifications Dimensions VIER
Page 331:
10.6 Conditions for using the softw
show all

User manual - teles

Create successful ePaper yourself

Delete template?

Save as template?