Download Manual for Aero-naut Buecker Jungmeister 133

More documents

Recommendations

Info

Bücker 133 JungmeisterBuilding Instructions Bü-133 Jungmeister10
Bücker 133 JungmeisterText from the plan:1 Glue the star, part 20, to the motor, part 39,using STABILIT-Express. Glue the motor tothe cowl, part 2, using thickened resin2 Wing incidence relative to tailplane +1º3 Spinner, Order No.4 Glue the exhaust, part 41, in the opening inthe cowl, part 2, using STABILIT-Express5 Wing incidence relative to tailplane +1.5º6 Suggested installation of ACTRO 12-5 motor,Order No. 7002/057 Reinforce with woven glass tape8 Order No. 7002/88: GRP motor bulkhead andstand-off pillarsThree 0.8 mm thick washers for sidethrust anddownthrust; fit under this pillar only.9 Glue undercarriage leg fairings, parts 38L +38R, to completed undercarriage assemblyusing STABILIT-Express10 Solder part 36 into collet - see buildinginstructions11 Glue mudguard 35 to part 36 using STABILIT-Express12 Bind joint tightly with soft wire, solder jointcarefully13 Applying the hinge tape14 Hinge tape (short pieces)15 Hinge tape (full-length)16 Jig S117 Adjusting the top wing using the jigs S118 We reserve the right to modify any feature inorder to improve our products19 Top wing - dihedral20 Bottom wing - dihedral21 Plan view of bottom wing22 View B23 Position of jig S1 when adjusting the top wing24 Removable seat (23) for access to battery25 Fix receiver to fuselage side with Velcro(hook-and-loop) tape26 Bind tightly with soft wire, solder together27 Glue profiled cabane fairing strips, part 13, tocompleted cabane assembly using STABILIT-Express28 Black fuel tubing, 3 ØBlack fuel tubing, 2 Ø, not included29 Velcro (hook-and-loop) tape30 Receiver aerial guide tube31 Edge of decal32 Section B-B33 Shorten part 7234 Bend the “star”, part 20, to shape and solder thejoints35 Solder braces, parts 14, 15, to main undercarriagelegs, part 31; see building instructions36 Brass main wheel bush, part 3437 Hole for receiver aerial sleeve, part 3038 Aileron servo lead39 Relieve top of channeled rail - see buildinginstructions40 Cut slot - see building instructions41 Solder parts 9 and 10 to washers, part 7742 Glue cabane struts, parts 9 and 10, in brasssleeves, part 7, using laminating resin43 Slot (left-hand side) - rudder linkage44 Slots (both sides) - elevator linkage45 Fix sleeves, part 30, with thin cyano46 Fix aileron horn 56 with laminating resin47 Section A-A48 Solder washers, part 55, to interplane struts, part5449 View A50 Installation of elevator servo (right-hand fuselageside)51 Section C-C52 Template S253 Solder washer, part 55, to tailwheel unit, part 6654 Tailwheel - see building instructions55 Flight battery: 10 - 12 cells, 1.7 - 2.0 Ah capacity56 Centre of Gravity (C.G.) 43 - 51 mm57 30 mm - see building instructions58 Glue M3 nuts in place using STABILIT-Express59 Glue remainder of part 54 in the cowl and exhaustusing STABILIT-ExpressBuilding Instructions Bü-133 Jungmeister11
Page 1 and 2: Bücker 133 JungmeisterBuilding Ins
Page 3 and 4: Bücker 133 JungmeisterCaution: the
Page 5 and 6: Bücker 133 Jungmeisterdie-cut part
Page 7 and 8: Bücker 133 JungmeisterCheck that t
Page 9: Bücker 133 Jungmeister46 Servo mou

Download Manual for Aero-naut Buecker Jungmeister 133

Create successful ePaper yourself

Delete template?

Save as template?