MOTLoad Firmware Package User's Manual - Bustec

More documents

Recommendations

Info

1 2 3 4Chapter 1 Hardware Preparation and InstallationThe MVME6100 is factory tested and shipped with the configuration described in the followingsections.Figure 1-1. MVME6100 LayoutJ42J7J8J29J21J22S4PCI MEZZANINE CARDS11 2 3 4 5 6 7 81 2 3 4 5 6 7 8S3J23J24P1J11J12PCI MEZZANINE CARDPMCIPMCJ3J30J13J1410/100/1000LAN 2J910/100/1000 DEBUGLAN 1J93J19U12U32P2ABT/RSTS2J44296 06046MVME6100 Installation and Use (V6100A/IH2)
Chapter 1 Hardware Preparation and InstallationSCON Header (J7)A 3-pin planar header allows the choice for auto/enable/disable SCON VME configuration. Ajumper installed across pins 1 and 2 configures for SCON always enabled. A jumper installedacross pins 2 and 3 configures for SCON disabled. No jumper installed configures for autoSCON.J7J7J7123123123Auto-SCON(factory configuration)Always SCONNo SCONPMC/IPMC Selection Headers (J10, J15 – J18, J25 – J28)Nine 3-pin planar headers are for PMC/IPMC mode I/O selection for PMC slot 1. These nineheaders can also be combined into one single header block where a block shunt can be usedas a jumper.A jumper installed across pins 1 and 2 on all nine headers selects PMC1 for PMC I/O mode. Ajumper across pins 2 and 3 on all nine headers selects IPMC I/O mode.IPMC P2 I/O for IPMC Mode(factory configuration)J10J15J16J17J18J25J26J27J28111111111222222222333333333PMC1 P2 I/O for PMC ModeJ10J15J16J17J18J25J26J27J28111111111222222222333333333MVME6100 Installation and Use (V6100A/IH2) 7
Page 1 and 2: MVME6100 Single-Board ComputerInsta
Page 3 and 4: Safety SummaryThe following general
Page 5 and 6: Motorola products with the CE marki
Page 7 and 8: ContentsCommand Line Help . . . . .
Page 9 and 10: List of FiguresFigure 1-1. MVME6100
Page 11 and 12: About This ManualAbout This ManualT
Page 13 and 14: 1 HardwarePreparation and Installat
Page 15 and 16: Chapter 1 Hardware Preparation and
Page 17: Chapter 1 Hardware Preparation and
Page 25 and 26: 3 MOTLoadFirmware3IntroductionThis
Page 27 and 28: Chapter 3 MOTLoad FirmwareTest resu
Page 29 and 30: Chapter 3 MOTLoad Firmware■■■
Page 31 and 32: Chapter 3 MOTLoad FirmwareTable 3-1
Page 33 and 34: Chapter 3 MOTLoad FirmwareDefault V
Page 35 and 36: Chapter 3 MOTLoad FirmwareOutbound
Page 37 and 38: Chapter 3 MOTLoad Firmware■vmeCfg
Page 39 and 40: Chapter 3 MOTLoad FirmwareAlternate
Page 41 and 42: Chapter 3 MOTLoad FirmwareValid Boo
Page 43 and 44: Chapter 3 MOTLoad Firmware■ RAM h
Page 45 and 46: Chapter 4 Functional DescriptionTab
Page 47 and 48: Chapter 4 Functional DescriptionAll
Page 49 and 50: Chapter 4 Functional DescriptionSRA
Page 51 and 52: Chapter 4 Functional DescriptionPCI
Page 53 and 54: Chapter 4 Functional DescriptionNot
Page 55 and 56: Chapter 5 Pin AssignmentsConnectors
Page 57 and 58: Chapter 5 Pin AssignmentsTable 5-1.
Page 67 and 68: Chapter 5 Pin AssignmentsTable 5-11
Page 69 and 70:
Chapter 5 Pin AssignmentsTable 5-13
Page 71 and 72:
Chapter 5 Pin AssignmentsTable 5-14
Page 73 and 74:
Chapter 5 Pin AssignmentsBoundary S
Page 75 and 76:
Chapter 5 Pin AssignmentsNotes1. VM
Page 77 and 78:
Appendix A SpecificationsTable A-2.
Page 79 and 80:
Appendix B Thermal ValidationTable
Page 81 and 82:
Appendix B Thermal ValidationFigure
Page 83 and 84:
Appendix B Thermal ValidationNote M
Page 85 and 86:
CRelated DocumentationCMotorola Emb
Page 87 and 88:
Appendix C Related DocumentationTab
Page 89 and 90:
IndexAabort/reset switch 13air temp
show all

MOTLoad Firmware Package User's Manual - Bustec

Create successful ePaper yourself

Delete template?

Save as template?