MOTLoad Firmware Package User's Manual - Bustec

More documents

Recommendations

Info

FlammabilityAll Motorola PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by ULrecognizedmanufacturers.EMI CautionCaution!CautionThis equipment generates, uses and can radiate electromagnetic energy. It may causeor be susceptible to electromagnetic interference (EMI) if not installed and used withadequate EMI protection.Lithium Battery CautionThis product contains a lithium battery to power the clock and calendar circuitry.Caution!CautionDanger of explosion if battery is replaced incorrectly. Replace battery only with thesame or equivalent type recommended by the equipment manufacturer. Dispose ofused batteries according to the manufacturer’s instructions.Caution!AttentionIl y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplaceruniquement avec une batterie du même type ou d’un type équivalent recommandé parle constructeur. Mettre au rebut les batteries usagées conformément aux instructionsdu fabricant.Caution!VorsichtExplosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durchdenselben oder einen vom Hersteller empfohlenen Typ. Entsorgung gebrauchterBatterien nach Angaben des Herstellers.CE Notice (European Community)Warning!WarningThis is a Class A product. In a domestic environment, this product may cause radiointerference, in which case the user may be required to take adequate measures.
Motorola products with the CE marking comply with the EMC Directive (89/336/EEC). Compliance with thisdirective implies conformity to the following European Norms:EN55022 “Limits and Methods of Measurement of Radio Interference Characteristics of InformationTechnology Equipment”; this product tested to Equipment Class AEN50082-1:1997 “Electromagnetic Compatibility—Generic Immunity Standard, Part 1. Residential,Commercial and Light Industry”System products also fulfill EN60950 (product safety) which is essentially the requirement for the LowVoltage Directive (73/23/EEC).Board products are tested in a representative system to show compliance with the above mentionedrequirements. A proper installation in a CE-marked system will maintain the required EMC/safetyperformance.In accordance with European Community directives, a “Declaration of Conformity” has been made and ison file within the European Union. The “Declaration of Conformity” is available on request. Please contactyour sales representative.NoticeWhile reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc., assumesno liability resulting from any omissions in this document, or from the use of the information obtained therein.Motorola reserves the right to revise this document and to make changes from time to time in the contenthereof without obligation of Motorola to notify any person of such revision or changes.Electronic versions of this material may be read online, downloaded for personal use, or referenced inanother document as a URL to a Motorola website. The text itself may not be published commercially in printor electronic form, edited, translated, or otherwise altered without the permission of Motorola, Inc.It is possible that this publication may contain reference to or information about Motorola products (machinesand programs), programming, or services that are not available in your country. Such references orinformation must not be construed to mean that Motorola intends to announce such Motorola products,programming, or services in your country.Limited and Restricted Rights LegendIf the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the followingnotice shall apply unless otherwise agreed to in writing by Motorola, Inc.Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph(b)(3) of the Rights in Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights inNoncommercial Computer Software and Documentation clause at DFARS 252.227-7014 (Jun. 1995).Motorola, Inc.Embedded Communications Computing2900 South Diablo WayTempe, Arizona 85282
Page 1 and 2: MVME6100 Single-Board ComputerInsta
Page 3: Safety SummaryThe following general
Page 7 and 8: ContentsCommand Line Help . . . . .
Page 9 and 10: List of FiguresFigure 1-1. MVME6100
Page 11 and 12: About This ManualAbout This ManualT
Page 13 and 14: 1 HardwarePreparation and Installat
Page 15 and 16: Chapter 1 Hardware Preparation and
Page 25 and 26: 3 MOTLoadFirmware3IntroductionThis
Page 27 and 28: Chapter 3 MOTLoad FirmwareTest resu
Page 29 and 30: Chapter 3 MOTLoad Firmware■■■
Page 31 and 32: Chapter 3 MOTLoad FirmwareTable 3-1
Page 33 and 34: Chapter 3 MOTLoad FirmwareDefault V
Page 35 and 36: Chapter 3 MOTLoad FirmwareOutbound
Page 37 and 38: Chapter 3 MOTLoad Firmware■vmeCfg
Page 39 and 40: Chapter 3 MOTLoad FirmwareAlternate
Page 41 and 42: Chapter 3 MOTLoad FirmwareValid Boo
Page 43 and 44: Chapter 3 MOTLoad Firmware■ RAM h
Page 45 and 46: Chapter 4 Functional DescriptionTab
Page 47 and 48: Chapter 4 Functional DescriptionAll
Page 49 and 50: Chapter 4 Functional DescriptionSRA
Page 51 and 52: Chapter 4 Functional DescriptionPCI
Page 53 and 54: Chapter 4 Functional DescriptionNot
Page 55 and 56:
Chapter 5 Pin AssignmentsConnectors
Page 57 and 58:
Chapter 5 Pin AssignmentsTable 5-1.
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Chapter 5 Pin AssignmentsTable 5-11
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Chapter 5 Pin AssignmentsBoundary S
Page 75 and 76:
Chapter 5 Pin AssignmentsNotes1. VM
Page 77 and 78:
Appendix A SpecificationsTable A-2.
Page 79 and 80:
Appendix B Thermal ValidationTable
Page 81 and 82:
Appendix B Thermal ValidationFigure
Page 83 and 84:
Appendix B Thermal ValidationNote M
Page 85 and 86:
CRelated DocumentationCMotorola Emb
Page 87 and 88:
Appendix C Related DocumentationTab
Page 89 and 90:
IndexAabort/reset switch 13air temp
show all

MOTLoad Firmware Package User's Manual - Bustec

Create successful ePaper yourself

Delete template?

Save as template?