MOTLoad Firmware Package User's Manual - Bustec

More documents

Recommendations

Info

Chapter 3 MOTLoad FirmwareTable 3-1. MOTLoad Commands (continued)CommandtestRamRandomtestRtcAlarmtestRtcResettestRtcRollOvertestRtcTicktestSerialExtLooptestSeriallntLooptestStatustestSuitetestSuiteMaketestThermoOptestThermoQtestThermoRangetestWatchdogTimertftpGettftpPuttimetransparentModetsShowupLoadversionvmeCfgvpdDisplayvpdEditwaitProbeDescriptionRAM Random Data PatternsRTC AlarmRTC ResetRTC RolloverRTC TickSerial External LoopbackSerial Internal LoopbackDisplay the Contents of the Test Status TableExecute Test SuiteMake (Create) Test SuiteThermometer Temp Limit Operational TestThermometer Temp Limit Quick TestTests That Board Thermometer is Within RangeTests the Accuracy of the Watchdog Timer DeviceTFTP GetTFTP PutDisplay Date and TimeTransparent Mode (Connect to Host)Display Task StatusUp Load Binary Data from TargetDisplay Version String(s)Manages user specified VME configuration parametersVPD DisplayVPD EditWait for I/O Probe to Complete22MVME6100 Installation and Use (V6100A/IH2)
Chapter 3 MOTLoad FirmwareDefault VME SettingsAs shipped from the factory, the MVME6100 has the following VME configuration programmedvia Global Environment Variables (GEVs) for the Tsi148 VME controller. The firmware allowscertain VME settings to be changed in order for the user to customize the environment. Thefollowing is a description of the default VME settings that are changeable by the user. For moreinformation, refer to the MOTLoad User’s Manual and Tundra’s Tsi148 User Manual, listed inAppendix C, Related Documentation.■ MVME6100> vmeCfg –s –mDisplaying the selected Default VME Setting- interpreted as follows:VME PCI Master Enable [Y/N] = YMVME6100>The PCI Master is enabled.■ MVME6100> vmeCfg –s –r234Displaying the selected Default VME Setting- interpreted as follows:VMEbus Master Control Register = 00000003MVME6100>The VMEbus Master Control Register is set to the default (RESET) condition.■ MVME6100> vmeCfg –s –r238Displaying the selected Default VME Setting- interpreted as follows:VMEbus Control Register = 00000008MVME6100>The VMEbus Control Register is set to a Global Timeout of 2048 μseconds.■ MVME6100> vmeCfg –s –r414Displaying the selected Default VME Setting- interpreted as follows:CRG Attribute Register = 00000000CRG Base Address Upper Register = 00000000CRG Base Address Lower Register = 00000000MVME6100>The CRG Attribute Register is set to the default (RESET) condition.■ MVME6100> vmeCfg –s –i0Displaying the selected Default VME Setting- interpreted as follows:Inbound Image 0 Attribute Register = 000227AFInbound Image 0 Starting Address Upper Register = 00000000Inbound Image 0 Starting Address Lower Register = 00000000Inbound Image 0 Ending Address Upper Register = 00000000Inbound Image 0 Ending Address Lower Register = 1FFF0000Inbound Image 0 Translation Offset Upper Register = 00000000Inbound Image 0 Translation Offset Lower Register = 00000000MVME6100>MVME6100 Installation and Use (V6100A/IH2) 23
Page 1 and 2: MVME6100 Single-Board ComputerInsta
Page 3 and 4: Safety SummaryThe following general
Page 5 and 6: Motorola products with the CE marki
Page 7 and 8: ContentsCommand Line Help . . . . .
Page 9 and 10: List of FiguresFigure 1-1. MVME6100
Page 11 and 12: About This ManualAbout This ManualT
Page 13 and 14: 1 HardwarePreparation and Installat
Page 15 and 16: Chapter 1 Hardware Preparation and
Page 25 and 26: 3 MOTLoadFirmware3IntroductionThis
Page 27 and 28: Chapter 3 MOTLoad FirmwareTest resu
Page 29 and 30: Chapter 3 MOTLoad Firmware■■■
Page 31: Chapter 3 MOTLoad FirmwareTable 3-1
Page 35 and 36: Chapter 3 MOTLoad FirmwareOutbound
Page 37 and 38: Chapter 3 MOTLoad Firmware■vmeCfg
Page 39 and 40: Chapter 3 MOTLoad FirmwareAlternate
Page 41 and 42: Chapter 3 MOTLoad FirmwareValid Boo
Page 43 and 44: Chapter 3 MOTLoad Firmware■ RAM h
Page 45 and 46: Chapter 4 Functional DescriptionTab
Page 47 and 48: Chapter 4 Functional DescriptionAll
Page 49 and 50: Chapter 4 Functional DescriptionSRA
Page 51 and 52: Chapter 4 Functional DescriptionPCI
Page 53 and 54: Chapter 4 Functional DescriptionNot
Page 55 and 56: Chapter 5 Pin AssignmentsConnectors
Page 57 and 58: Chapter 5 Pin AssignmentsTable 5-1.
Page 67 and 68: Chapter 5 Pin AssignmentsTable 5-11
Page 73 and 74: Chapter 5 Pin AssignmentsBoundary S
Page 75 and 76: Chapter 5 Pin AssignmentsNotes1. VM
Page 77 and 78: Appendix A SpecificationsTable A-2.
Page 79 and 80: Appendix B Thermal ValidationTable
Page 81 and 82: Appendix B Thermal ValidationFigure
Page 83 and 84:
Appendix B Thermal ValidationNote M
Page 85 and 86:
CRelated DocumentationCMotorola Emb
Page 87 and 88:
Appendix C Related DocumentationTab
Page 89 and 90:
IndexAabort/reset switch 13air temp
show all

MOTLoad Firmware Package User's Manual - Bustec

Create successful ePaper yourself

Delete template?

Save as template?