General Information Gates/Rohloff - Koga Signature

More documents

Recommendations

Info

mountingFlat Wrench SW46Art. Nr. 10400006POM-Sprocket-KeyArt. Nr. siehe TabelleTitlePart NumberBasiswerkzeug 10400001Aufsatz 19 Zähne 10400002Aufsatz 20 Zähne 10400003Aufsatz 22 Zähne 10400004Aufsatz 24 Zähne 10400005Mounting the Rear Sprocket M46x6 to the Gates-Rohloff CarrierM46x6The Gates-Rohloff Carrier M46x6 by Rohloff (Art. No. 10300101) is where the Gates CarbonDrive System and the Rohloff SPEEDHUB 500/14 (Illustration 1) come together. At the timeof delivery the Gates Carrier may already be fitted to the hub. If this is not the case, pleasefollow the instructions for retrofitting the carrier to your hub.Illustration 1:Rohloff SPEEDHUB 500/14with Gates-Rohloff CarrierM46x6 and Rear SprocketM46x624
mountingLubricate the inner thread of the Rear Sprocket M46x6 and carefully screw it on to theCarrier as far as possible by hand (illustration 3). As shown in illustration 3, the flange ofthe rear sprocket needs to be on the hub side. Make sure to bring the parts together inthe right angle and do not cant them. Tighten the Rear Sprocket M46x6 with the POM-Sprocket-Key (Art. No. 10400001, 1040000X), to keep the sprocket and the Carrier fromloosening from the hub in future mounting processes. To keep the hub from rotatingwhile you thread on the carrier, you may hold the driver (sprocket thread) in place with theRohloff Sprocket Tool and an Open-end Wrench SW24 (illustration5). Always make sure thatthe Rohloff Sprocket tool is seated correctly and secured in place.2Please note:Always secure the Sprocket tool, as described in the Rohloff Owners Manual (chapterService, paragraph 3 „Sprocket reversing/replacing“), using a quick release skewer (CCversions), or an axle nut (TS versions), to avoid damage to the driver (sprocket thread).(Illustration 2).Illustration 2:Securing the RohloffSprocket tool with quickrelease skewer or axle nutIllustration 3:Rohloff SPEEDHUB 500/14with Gates Rohloff CarrierM46x6 and Rear SprocketM46x6www.carbondrivesystems.com25
Page 2 and 3: ContentCongratulations! 4For your s
Page 4 and 5: first stepsCongratulations!Thank yo
Page 7: first steps1Mounting the tensioned
Page 11 and 12: mountingMounting the Gates Carbon D
Page 13 and 14: mounting2Illustration 3:Correct ali
Page 15 and 16: mountingChecking the belt tension2P
Page 17 and 18: mountingChecking the belt tension w
Page 19 and 20: mountingaxle. If the Snubber is loc
Page 21 and 22: mounting2Shim ring for bottombracke
Page 23: mountingMounting the Gates Carbon D
Page 28 and 29: mountingIllustration 8:Mounting the
Page 30 and 31: 3exchange• When does the Gates Ca
Page 32 and 33: exchangeIllustration 2:Wearing off
Page 34 and 35: 4forFrame builders• Frame require
Page 36 and 37: for Frame buildersIllustration 2:Ex
Page 39 and 40: atio overview19 Teeth rear 20 Teeth
Page 41 and 42: atio overviewSprocket-size combinat
Page 43: Find more information for Europe:Un

General Information Gates/Rohloff - Koga Signature

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?