Instruction Manual - Biometra

More documents

Recommendations

Info

Language/Sprache:German/DeutschEnglish/EnglischInfo Cancel EnterTo confirm your selection press [Enter]5.7.4 Display contrastThe display contrast can be set in 4 levels to achieve optimum visibility under individual lightconditions.Select Display Contrast, press [Enter]Contrast (0-4 or arrows): 2Info Cancel EnterUser cursor keys to in/decrease contrast value or directly enter setting.The default setting is “2” which meets average conditions.5.7.5 DiagnosticsThe diagnostic screen contains internal information used by the Biometra service departmentfor servicing.5.7.6 Temperature readoutEach T3000 block can be equipped with an in tube-temperature sensor (050-408 for 0.2mlwells; 050-409 for 0.5ml wells). This sensor is to monitor the temperature inside a test tube.The temperature of the in tube-sensor can be shown in the T3000 display. The sensor displaywill replace the display of the lid temperature.Temperature read out:Heated lidTube -SensorCancelEnterNote: The in tube sensor is NOT used to control the instrument.38 Instruction Manual T3000 10/2009
6 Short manualSafety WarningsDo not open the instrument unless you are authorised to do so. Check thelabel at the backside if the instrument has correct voltage configuration (100V, 115 V or 230 V).Thermocycler main menuThe thermoblock and the heated lid are reaching high temperatures duringoperation. Both thermoblock and heated lid can burn you.Rapid heating of the thermoblock can cause liquids to boil explosively.Always wear safety goggles during operation. Close the lid before starting aprogram.It is not necessary to apply oil into the opening of the block in order toimprove the heat transfer between the block and the sample tubes.If you still decide to use oil, do not use silicon oil. Mineral oil may be used.Ensure that both the rear and bottom ventilation slits at the rear and bottomof the instrument are unobstructed. Insufficient ventilation can causeoverheating of the instrument. Tip: At regularly intervals clean the bottom'sventilation slits from dust to ensure maximum venting capability.ProgStepTempTimeLid23.9C24.0C23.8C23.9C23.9C23.9CInfo System Start/Stop EditSoftkey 1 Softkey 2 Softkey 3 Softkey 4The function of the four soft keys beneath the display is context sensitive. The respectivefunction is shown in the display. The function of each key can differ from screen to screen.Create programPress [Edit] to enter the edit mode.Select a subdirectory with the cursor keys . Press [Enter]Select a program with cursor keys or by number Press [Edit]Instruction Manual T3000 10/2009 39
Page 1 and 2: Instruction ManualVer. 09/10ModelOr
Page 5 and 6: 14 Warranty........................
Page 7 and 8: 1.3 Technical specifications T3000
Page 9 and 10: 2 Safety and Warning Notices2.1 Def
Page 11 and 12: This instrument is designed and cer
Page 14 and 15: T3000 ThermocyclerSerial numberBloc
Page 16 and 17: 4.2 The T3000 Thermocycler rear vie
Page 18 and 19: 4.4 The high performance smart Lid
Page 20 and 21: ProgStepTempTimeLid23.9C24.0C23.8C2
Page 22 and 23: Use cursor keys to select next lett
Page 24 and 25: Note: There is a convention on how
Page 26 and 27: - 3: -------------- 3: BIOMETRANu
Page 28 and 29: Insert / Delete step: 31: 62.0 0h 5
Page 30 and 31: 5.4.4 Delete programCopy- 3: -----
Page 32 and 33: Temp[C] Time ← # Options -->1: 62
Page 34 and 35: - 0:Start block 2- 1:- 2:- 3:-
Page 36 and 37: Prog3: BiometraStep 1Temp 20.3 62.0
Page 40 and 41: Enter program name- 3: -----------
Page 42 and 43: dt[s]: Time increments. To compensa
Page 44 and 45: Important: When the clutch mechanis
Page 46 and 47: 9 Accessories9.1 PlasticwareBiometr
Page 48 and 49: 10.2 Packing of the ThermocyclerBio
Page 50 and 51: General Information for Decontamina
Page 52 and 53: 13 EU - Konformitätserklärung / E
Page 54: 15 Subject IndexDeclaration of Conf

Instruction Manual - Biometra

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?