LM8000 Operation/Installation Manual - Balboa Direct

More documents

Recommendations

Info

<strong>Balboa</strong> Domestic Wiring Configuration - Board No. 57129<strong>LM8000</strong> — PN 5712903/29/11LINE12VDCMP3J4J11AUDIO CONTROL LIGHTFMANTENNA J2J3SPKR 1 SPKR 2 SPKR 3 SPKR 4J16 J9 J12 J13 J8INSTALL CONTROL MODULE57130 THRU LIDLR4 REV A CEI 10-12-09J5LED 1 LED 2J10J14AUXPUMP 1PUMP 2BLOWERCIRCOZONE120VHTRJ1240VHTRP11L2NEUTRALP9RELAYSF1 30A 250VF2 30A 250VF3 20A 250VP7 VOLTAGEHTR 1 HTR 2 P1 L P1 HIGH P2 L P2 HIGH BLWRCIRC&O3NEUTRALCIRCO3HEATERSENSORJ19TRANSSECONDARYJ20P14P12 P13P10 P9P7P2P8J33 J32J23 J21 J22 J25J26 J30P3P6AUXLIGHTAUX LCDBLACK L1GND COPPERWHITE NEUTRANSPRIMARYHEATERSENSORJ18120VACTRAMSFORMER4.0 kW HEATERGROUNDFUSED LINE 1SWITCHED LINE 2 OR NEUTRAL - LOW SPEEDSWITCHED LINE 2 OR NEUTRAL - HIGH SPEEDCONNECT ONLY TO CIRCUITS PROTECTED BY A CLASS A GFCI.A DISCONNECTING MEANS MUST BE INSTALLED WITHIN SIGHT FROMTHE EQUIPMENT AND AT LEAST 5 FEET (1.52 M) FROM THEINSIDE WALLS OF THE POOL, SPA, OR HOT TUB.USE COPPER CONDUCTORS ONLY.EMPLOYER UNIQUEMENTDES CONDUCTEURS DE CUIVRE.#6 AWG MIN. WIRE= 90°FOR SUPPLY CONNECTIONS,USE CONDUCTORS SIZED ON THEBASIS OF 60°C AMPACITY BUTRATED MINIMUM OF 90°C.SPA-SIDE CONTROL PANELJ10TORQUE RANGE FORMAIN TERMINAL BLOCK (J1):21-23 IN. LBS.DEVICE VOLTS FROM TO OTHERHEATER 120V P6 P8 1.0 KWHEATER 240V P6 P11 4.0 KWAUX, P1, P2, BL 120V P7 P9AUX, P1, P2, BL 240V P7 P10CIRC, OZONE 120V P12 P13CIRC, OZONE 240V* P12 P14**P14 VOLTAGE IS DETERMINED BY P7.P7 MUST BE CONNECTED TO P10 FOR 240VLOCATION DEVICE VOLTS AMPS FROM TOJ5 LIGHT 12V 1AJ21 PUMP 1 240V 12A MAX P7 P10J22 PUMP 2 240V 12A MAX P7 P10J23 AUX** 240V 4AJ25 BLOWER 240V 4A P7 P10J26 CIRC 240V 1A P12 P14J30 OZONE 24OV 1A P12 P14HTR HEATER 240V 4.0 kW HTR TERM J32 & J33**ANY DEVICE POWERED BY J23 MUST CARRY ITS OWN FUSINGTOTAL OUTPUT AMP DRAW NOT TO EXCEED MAX INPUT RATING OF SPAUSE EARTH GROUND CONNECTIONS AS INDICATED INSIDE THE SYSTEM ENCLOSUREELECTRIC SERVICE240 VAC - 60 Hz48 AMP MAXRED L2GNDGND COPPER20
120V & 240V Wiring with Heater OptionsWARNING: DISCONNECT THE ELECTRIC POWER BEFORE SERVICINGAVERTISSEMENT : DÉBRANCHEZ L'ÉNERGIE ÉLECTRIQUE AVANT L'ENTRETIENFOR SUPPLY CONNECTION, SELECT WIRE BASED ON 90°C.POUR le RACCORDEMENT, d'APPROVISIONNEMENT, FIL CHOISI BASÉ SUR 90°C.USE COPPER CONNECTORS ONLY.UTILISEZ LES CONNECTEURS DE CUIVRE SEULEMENT.USE CLASS A GROUND FAULT CIRCUIT INTERRUPTER.UTILISEZ LA CLASSE UN CIRCUIT DE AUTE DE TERRE INTERRUPTEUR.21
Page 1 and 2: LM8 - Low Maintenance SystemInstall
Page 3: Table of ContentsImportant Notices
Page 6 and 7: Overview (cont.)OPERATIONTurn on Je
Page 8 and 9: Configuration and OperationCONFIGUR
Page 10 and 11: PUMP AND BLOWER SETTINGSThe pump an
Page 12 and 13: FILTRATION SETTINGSHome > Setup > F
Page 14 and 15: MODEHome > Setup > ModeIf Economy M
Page 16 and 17: SCREENSAVERThe screensaver activate
Page 18 and 19: LED LIGHTINGHome > Mood > LEDs > Se
Page 22 and 23: SpecificationsEnvironmentalOperatin
Page 24 and 25: Troubleshooting (cont.)14.15.16.24P
Page 26 and 27: IndexSymbols3 red jumpers 2512 VAC
Page 28: Tustin, Ca. 92780 (714) 384-0384 42

LM8000 Operation/Installation Manual - Balboa Direct

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?