Robin Z5xx Datasheet - Toradex

More documents

Recommendations

Info

Robin Z5xx DatasheetLED3: On board flash drive and SATA bridge activity indication. The LED shows the activity parallel tothe ATA_ACT# signal (pin A28 on COM express connector).4.11. LPCThe LPC interface is a Low Pin Count PCI bus. Components on the carrier board such as Super IO oran external BIOS are connected to this bus.Note for external LPC devices: Don’t use a clock repeater on the carrier board for the clock signal ofthe LPC.Toradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l info@toradex.com Page | 22
Robin Z5xx Datasheet5. Power Supply5.1. Power StatesState Common Names BehaviorG3 Mechanical Off All power supplies except the RTC battery are removed. The power consumption of thesystem is almost zero; only the RTC circuit consumes a small amount of powerS5 Soft Off Only the embedded controller on the module is powered. The embedded controller waits forthe power button to be pushed before starting the system. The power consumption in thisstate is very low.S4S3Suspend to DiskHibernationSuspend to RAMStand by, SleepThe contents of RAM are written to a non-volatile storage medium (e.g. hard disc). This allowsrecovery of the system to the state prior to entering suspend or hibernate. From the hardwareperspective, this state is equal to S5. The system is off except for the embedded controllerbeing powered. The embedded controller waits for the power button to be pushed beforestarting the system. The power consumption in this state is very low. The Robin hardwaredoes not distinguish between S4 and S5.The RAM subsystem is powered for a fast recovery of the system. Power supplies that are notrequired are switched off. Wake on LAN is supported in this state (hence the networksubsystem is powered). The Robin module requires the main power supply to generate thestandby power supply.S0 On The system is working. All power supplies are switched on. The power consumption dependson the CPU and peripheral load.The COM Express Connector features three signals for signaling the different power states to thecarrier board. As the Robin module hardware does not distinguish between power states S4 and S5,SUS_S4# and SUS_S5# are essentially the same signal.State SUS_S5# SUS_S4# SUS_S3#G3 NA NA NAS5 Low Low LowS4 Low Low LowS3 High High LowS0 High High HighToradex AG l Altsagenstrasse 5 l 6048 Horw l Switzerland l +41 41 500 48 00 l www.toradex.com l info@toradex.com Page | 23
Page 4 and 5: Robin Z5xx Datasheet5.2.2 ATX-Like
Page 6 and 7: Robin Z5xx Datasheet1. Introduction
Page 8 and 9: Robin Z5xx Datasheet2.2. VariantsFr
Page 10 and 11: Robin Z5xx Datasheet2.5. Difference
Page 12 and 13: Robin Z5xx Datasheet3.2.2 Signal Vo
Page 14 and 15: Robin Z5xx DatasheetPin Signal Type
Page 16 and 17: Robin Z5xx DatasheetPin Signal Type
Page 18 and 19: Robin Z5xx Datasheet3.4. Assignment
Page 20 and 21: Robin Z5xx Datasheet4.3.2 USB clien
Page 24: Robin Z5xx Datasheet5.2. Power Supp
Page 27 and 28: Robin Z5xx Datasheet5.2.4 Configura
Page 29 and 30: Robin Z5xx Datasheet5.3. Power Sequ
Page 31 and 32: Robin Z5xx Datasheet5.3.4 S0 to S3
Page 33 and 34: Robin Z5xx Datasheet6. Robin Embedd
Page 35 and 36: Robin Z5xx Datasheet6.2. INTERRUPT
Page 37 and 38: Robin Z5xx DatasheetDIR7..DIR0: 0 =
Page 39 and 40: Robin Z5xx Datasheet6.4.5 Service W
Page 41 and 42: Robin Z5xx Datasheet7. WatchdogThe
Page 43 and 44: Robin Z5xx Datasheet8. Thermal cons
Page 45 and 46: Robin Z5xx Datasheet9. Technical Sp
Page 47 and 48: Robin Z5xx Datasheet9.3.3 Details w

Robin Z5xx Datasheet - Toradex

Create successful ePaper yourself

Delete template?

Save as template?