Catalog IC 10 Â· 2012 - Industry

More documents

Recommendations

Info

8For Use in the Control CabinetET 200S Motor Starters and Safety Motor StartersStandard terminal modules© Siemens AG 2012Conductor cross-sections• Solid mm 2 2 x (1 ... 2.5) 1) or 2 x (2.5 ... 6) 1)• Finely stranded with end sleeve mm 2 1 x 10 or2 x (1 ... 2.5 ) 1) or 2 x (2.5 ... 6) 1)according to IEC 60947• AWG cables, solid or stranded AWG 2 x (14 ... 10)• With additional three-phase feeder terminal if required- Solid or stranded mm 2 1 x 2.5 ... 25- Finely stranded with end sleeve mm 2 1 x 2.5 ... 25- AWG cables, solid or stranded AWG 1 x 12 ... 4Wiring• Required tool Standard screwdriver size 2 and Pozidriv 2• Tightening torque Nm 2.0 ... 2.51) If two different conductor cross-sections are connected to one clampingpoint, both cross-sections must lie in the range specified. If identical crosssectionsare used, this restriction does not apply.■ Selection and ordering dataTM-RS90TM-RS130/TM-FRS130Version DT Order No. Priceper PUPU(UNIT,SET, M)PS*PGTerminal modules for Standard motor startersTM-DS45-S32for DS1-x direct-on-line starterswith incoming power for bus connectionincluding three caps for terminating the power busA 3RK1 903-0AB00 1 1 unit 42D3RK1 903-0AB00TM-DS45-S31for DS1-x direct-on-line starterswithout incoming power bus connectionA 3RK1 903-0AB10 1 1 unit 42D3RK1 903-0AB10TM-RS90-S32for RS1-x reversing starterswith incoming power bus connectionincluding three caps for terminating the power busA 3RK1 903-0AC00 1 1 unit 42D3RK1 903-0AC00TM-RS90-S31for RS1-x reversing starterswithout incoming power bus connectionA 3RK1 903-0AC10 1 1 unit 42D8/92 Siemens IC 10 · 2012* You can order this quantity or a multiple thereof.Illustrations are approximate
© Siemens AG 2012For Use in the Control CabinetET 200S Motor Starters and Safety Motor StartersHigh-Feature motor starters■ OverviewFunctionality of the High-Feature motor starters• Basic functionality see "General Data" ➞ "Overview"on page 8/84.• Direct-on-line, reversing or soft starter up to 7.5 kW• With wide range in 3 setting ranges, with 0.3 to 3 A,2.4 up to 8 A, 2.4 to 16 A available• With combination of starter circuit breaker, electronic overloadprotection (parameterizable), and contactor or soft starter• Power bus up to 50 A• Upper and lower current limits for plant and process monitoring• Motor stall protection, zero current detection and asymmetrydetection integrated• The actual motor current is measured and transmitted fordiagnostics in the cyclic process image• Control of the motor starter from the control system and extensivediagnostics status via the cyclic process image• Optional digital inputs available in the cyclic process imageand flexibly assignable with functions for adaptation to allapplications• Detection of the switching state of the starter circuit breaker viaaux. switches and of the contactor via current evaluation• Integrated isolating function using starter circuit breakers• Local safety engineering possible (without failsafe kit in thecase of the HF starter, because the function of the failsafe kit isalready integrated)• Front-mounting 2DI LC COM control module for 2 moreparameterizable digital inputs• Optional "Motor Starter ES" software for easy commissioningand diagnostics - from 11/2011 also for the new .-.AB4 -Starteravailable (see Chapter 14 "Parametrization, Configuration andVisualization with SIRIUS")• PROFIenergy capable (only with the new .-.AB4 -starters)• Supplying the motor current in PROFIenergy format- Switching off during dead times• All acyclic services DPV1 supported by PROFIBUS andPROFINET (only with the new .-.AB4 -starters)- Changing of parameters during operation, e.g. the ratedoperational current- Reading and writing acyclic data for exact diagnostics of theunit or process and for analysis of the plant statusSelective protection concept forET 200S High-Feature motor startersAs a result of the selective protection concept (separate trippingof short circuit and overload) with solid-state overload evaluation,additional advantages are realized on the High-Feature motorstarters – advantages which soon make themselves positivelyfelt particularly in manufacturing processes with high plantstoppage costs:• Only two versions up to 7.5 kW – hence little order variance andstock keeping• All settings can be parameterized by bus – hence fullTIA capability• Separate signaling of overload and short circuit – enablesselective diagnostics• Overload can be acknowledged by remote reset – ideal forhighly automated plants• Current asymmetry monitoring – complete monitoring of themotor• Stall protection – complete monitoring of the motor• Emergency start function in case of overload – operation is possiblein an emergency• Current value transmission via bus – monitoring of the application• Current limit monitoring• Trip class can be parameterized – overload trip can be adaptedto the application• Type of coordination "2" – still functional after short circuit withmagnitude of 50 kA• Very high contact enduranceET 200S High-Feature motor starter: DS1e-x direct-on-line starter(innovated .-.AB4 starters)ET 200S High-Feature motor starter: DS1e-x direct-on-line soft starter(innovated .-.AB4 starter)ET 200S High-Feature motor starter: Reversing starter (reversing starter)RS1e-x (innovated .-.AB4 -Starter)8Siemens IC 10 · 20128/93
Page 1: © Siemens AG 2012For Use in the Co
Page 4 and 5: For Use in the Control CabinetET 20
Page 12 and 13: © Siemens AG 2012For Use in the Co
Page 14 and 15: 8For Use in the Control CabinetET 2
Page 56: For Use in the Control CabinetET 20

Catalog IC 10 Â· 2012 - Industry

Create successful ePaper yourself

Delete template?

Save as template?