Catalog IC 10 Â· 2012 - Industry

More documents

Recommendations

Info

8For Use in the Control CabinetET 200S Motor Starters and Safety Motor StartersHigh-Feature terminal modules© Siemens AG 2012■ OverviewTerminal module TM-DS, TM-RSMore information see also "General Data" ➞ "Overview" ➞ section"Power Supply through Terminal Modules" on page 8/84 onwards.• "–S32" version with incoming connection: 2 x 3 x 10 mm² screwterminals for power bus and motor feeder• "–S31" version without incoming connection: 1 x 3 x 10 mm²screw terminals for motor feeder• Optionally expandable with PE/N modules (see "Accessories")■ Technical specificationsSee page 8/91.■ Selection and ordering dataVersion DT Order No. Priceper PUPU(UNIT,SET, M)PS*PGTerminal modules for High-Feature motor startersTM-DS65-S32for DS1e-x and DSS1e-x direct-on-line starterswith incoming power bus connection including threecaps for terminating the power busTM-DS65-S31for DS1e-x and DSS1e-x direct-on-line starterswithout incoming power bus connectionTM-RS130-S32for RS1e-x reversing starterswith incoming power bus connection including threecaps for terminating the power busTM-RS130-S31for RS1e-x reversing starters3RK1 903-0AK00Without incoming power bus connectionA 3RK1 903-0AK00 1 1 unit 42DA 3RK1 903-0AK10 1 1 unit 42DA 3RK1 903-0AL00 1 1 unit 42DA 3RK1 903-0AL10 1 1 unit 42D8/96 Siemens IC 10 · 2012* You can order this quantity or a multiple thereof.Illustrations are approximate
© Siemens AG 2012For Use in the Control CabinetET 200S Motor Starters and Safety Motor StartersPower modules■ Overview• Disconnection of a complete group of motor starters is possiblewithout any additional outlay (safety category 1according to ISO 13849-1)• PM-D power modules are plugged onto the TM-P15 terminalmodules. (A PM-D power module must be followed by at leastone motor starter or one frequency converter.)PM-D power modules are used for monitoring the two 24 V DCauxiliary voltages for the group of motor starters following on theright or for supplying power to the group of frequency convertersfollowing on the right. The voltage is fed in through TM-D terminalmodules to the self-assembling potential bars.A voltage failure is signaled through PROFIBUS diagnostics tothe higher-level master. Additional LEDs inform locally about thestatus of the auxiliary voltages.The separation of auxiliary voltages for signal checkback andpower section actuation enables the entire group to be shutdown while maintaining the diagnostics capability.■ Technical specificationsRated control supply voltage U sup to 60 °CRated operational current I e• Recommended short-circuitprotectionPM-D power modules3RK1 903-0BA00V 20.4 ... 28A 10• Melting fuse A 10• Miniature circuit breaker A 10, tripping characteristic BPower consumption from the backplanemA ≤ 10busSupply of• Motor startersYes• Frequency convertersYes• Motor starters for safety technology No• Solid-state modulesNo•Ex(i) modulesNoAlarmsNoneDiagnostics functionsYes• System fault/device faultRed "SF" LED• Monitoring the control supply voltage Green "PWR" LEDfor solid-state modules U 1• Monitoring the control supply voltage Green "CON" LEDfor contactors U 2• Diagnostics information can be read YesoutConductor cross-sections• Flexible with end sleeve mm 2 1.5• Rigid mm 2 2.5Mounting dimensions (W x H x D) mm 15 x 195.5 x 117.58■ Selection and ordering dataVersion DT Order No. Priceper PUPU(UNIT,SET, M)PS*PGPower modulesPM-D power modulesfor 24 V DC with diagnosticsA 3RK1 903-0BA00 1 1 unit 42D3RK1 903-0BA00* You can order this quantity or a multiple thereof.Illustrations are approximateSiemens IC 10 · 20128/97
Page 1: © Siemens AG 2012For Use in the Co
Page 4 and 5: For Use in the Control CabinetET 20
Page 10 and 11: 8For Use in the Control CabinetET 2
Page 12 and 13: © Siemens AG 2012For Use in the Co
Page 56: For Use in the Control CabinetET 20

Catalog IC 10 Â· 2012 - Industry

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?