rotary press trailer system specification - The City of Titusville, Florida

More documents

Recommendations

Info

1.07 – Performance RequirementsA. The dewatering system shall be capable of operating both continuously and intermittently.B. At no time shall it be required to have more than two (2) dewatering channels per Rotary Fan Press System tomeet these Performance Requirements.C. Any changes to Condition of Service as listed above that affects the performance of the equipment shall be theresponsibility of the Owner for any required corrective action to meet these requirements.D. It shall be the responsibility of the selected chemical/polymer supplier to furnish the appropriate chemical/polymerfor the manufacturer to meet performance requirements listed above.E. Performance requirements shall not be part of any contract and/or performance of delivery bond liability andshall be covered by the manufacturer’s written warranty stating all coverage’s and remedies for meeting the performancerequirements of the specification.1.08 – SubmittalsA. Submit within twenty (20) working days of notice to proceed, three (3) copies of the following information insufficient detail to demonstrate that the proposed equipment fully meets the requirements of the specification.Each copy of the submittal shall be assembled in one (1) or more loose leaf three (3) ring hard backed binders.Each binder shall be clearly labeled with identifying cover showing project, manufacturer’s name and modelnumber.B. Installation and Storage – Overall drawings showing dimensions, connecting utility sizes, locations and otherpertinent installation data. Recommended storage protection for the equipment furnished.C. Shop Drawings – Dimensional shop and erection drawings for all equipment supplied under this section alongwith all interconnecting components.D. Descriptive Literature – Catalog cut sheets, technical data, performance curves and utility requirements for allequipment supplied under this section.E. Electrical – Detailed wiring diagrams, instrumentation and operational description of entire control system.F. Operation and Maintenance Instructions – These sections are to be from the complete operation and maintenancemanual as will be provided upon delivery of equipment.G. Warranty – Signed warranty. Statements outlining the manufacturer’s ability to timely furnish repairs and servicereplacement parts when and if so required.1.09 – Operating and Maintenance DataA. The manufacturer shall provide a total of two (2) printed copies and one (1) CD (if specified) per unit specifiedof a complete and comprehensive reference manual containing operating and maintenance data to enable operatorsand plant engineers to correctly operate, service and maintain all equipment and accessories covered by thespecification and drawings.B. The data contained in the manual shall explain and illustrate clearly and simply all principals and theory of operation,operating instructions, maintenance procedures, calibration procedures, safety precautions, troubleshootingprocedures, suggested forms for required record keeping, detailed equipment drawings, electrical andinstrumentation schematics.Rotary Press Trailer System Specification Page 4 of 16
C. Each copy of the manual shall be assembled in one (1) or more loose leaf three (3) ring hard backed binders.Each binder shall be clearly labeled with identifying cover showing project, manufacturer’s name and modelnumber. All composition and printing shall be arranged so that punching does not obliterate any data and eachsection shall be clearly marked. All information on the CD shall be of a pdf format.1.10 – Manufacturer’s Supervisory Services and TestingA. The Manufacturer shall furnish the services only of a qualified factory representative for a minimum period oftime at the job-site as listed below. Additional services, if requested, shall be available at the manufacturer’slisted portal to portal per diem rate in effect at time of delivery of service, plus all travel and living expenses.B. Installation:1. A minimum of one (1) trip and one (1) day at job-site; a qualified Prime Solution, Inc. representativeshall inspect all supplied equipment of the manufacturer for physical damage, correct placement for requiredservice, utility connections and general operation.C. Start-Up:1. The equipment manufacturer shall receive two (2) weeks written notice that all installation is completed,representative sludge is available and appropriate chemistry/polymer is on-site prior to arrivingfor start-up by the Owner and/or Contractor.D. Training:2. A minimum of three (3) days on-site shall be used to perform equipment and system start-up testing andcalibrations to be followed by training and performance testing within the same trip.3. Should the manufacturer’s representative arrive at the job-site and installation is not complete and/orthe appropriate chemistry/polymer is not on-site, the manufacturer shall be allowed to bill the Owner orContractor for the additional time and expense not covered under this specification.1. The manufacturer shall train the Owners personnel on equipment operation, maintenance and troubleshootingwith a minimum of four (4) hours of operation manual review and four (4) hours of hands onequipment and system operation.E. Performance Testing:1. Prior to the Performance/Acceptance Testing, the Owner’s selected chemical/polymer supplier shallperform testing of the sludge and supply the required chemistry/polymer for the manufacturer to meetthe performance requirements as listed in this specification.2. Testing shall consist of test samples taken once per hour and shall be grab samples.3. Samples shall be tested by an approved independent laboratory paid for by the Owner and of theOwner’s choosing. All results shall be given directly to the Owner and Manufacturer.4. In the case of non-acceptable performance due to the Manufacturer, Owner and/or Chemical/PolymerSupplier.A. Manufacturer – Should the Manufacturer’s equipment supplied per this specification be founddefective in meeting the functionality requirements, the Manufacturer shall have sixty (60) daysin which to prove functionality. At its sole expense, supplemental testing and equipment modificationsin order to perform any retest of the system to meet the requirements listed for the project.Rotary Press Trailer System Specification Page 5 of 16
Page 1 and 2: ROTARY PRESSTRAILER SYSTEM SPECIFIC
Page 3: C. Within five (5) business days of
Page 8 and 9: The following materials shall be pr
Page 10 and 11: C. All electrical components shall
Page 12 and 13: 2.08 - Trailerby the PLC and will t
Page 14 and 15: Fine Adjustment Sensitivity.Four (4
Page 16: Rotary Press Trailer System Specifi

rotary press trailer system specification - The City of Titusville, Florida

Create successful ePaper yourself

Delete template?

Save as template?