CBX 24 & 32 SBX 30 - Trademate Home Page

More documents

Recommendations

Info

e) If thermostatic radiator valves are fitted, a radiator must befitted with two lock shield valves, to enable correct operation ofthe pump-overrun facility.f) The following paragraphs outline the specifications of theitems fitted to the appliances.PUMP - The available pump head shown in Figure 6 is that inexcess of the appliance hydraulic resistance, i.e. that availablefor the system.67654327AVAILABLE PUMP HEADSSBX 30CBX 32CBX 24Pump Head (m H 2 0)10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18Flow Rate ltr/minEXPANSION VESSEL - The integral expansion vessel is prechargedto a pressure of between 0.5 and 1.0 bar. This shouldbe checked before the water system is filled. Details below showthe water system volume that is acceptable for this vessel. If thesystem water volume is larger then an additional vessel must befitted to the system. BS 5449 and BS 6798 give further detailsregarding expansion vessel sizing and sealed systems.Expansion Vessel RequirementsVessel charge andinitial system pressurebar 0.5 0.75 1.0 1.5Total water content of systemusing 8 L (1.54 gal) capacityexpansion vessel suppliedL 96 84 73 50with appliance.For systems having a largercapacity multiply the total systemcapacity in litres (gallons) bythese factors to obtain the total0.0833 0.093 0.109 0.156minimum expansion vesselcapacity required in litres.FILLING LOOP (CBX appliances only). The plumbing jigincorporates a filling loop that connects the DHW supply to theCH system. This is used to fill the CH system on installation andwhenever the water pressure has been removed for systemmodifications, etc. The filling loop complies with the water supply(water fittings) regulations 1999 Section G24.1 and G24.2. Analternative method of filling a sealed system is shown in Figure 9.(SBX appliance). A filling loop should be fitted at some point toallow the CH system to be filled. Two types are shown below.WATER TREATMENT, CLEANSING AND FLUSHING THEHEATING SYSTEMNOTE: British Standard BS7593: 1992 stresses the importanceof cleansing and flushing of the system to ensure it continues torun efficiently with the minimum of maintenance necessary.Halstead Boilers fully support this professional approach andrecommend that the system is cleansed with an effective chemicalcleanser and protected long term with a suitable inhibitor. Suchproducts are available from Fernox and Sentinal.CONTROLS. As a minimum it is recommended that a roomthermostat be installed to control the appliance. Thermostatic radiatorvalves may be fitted to the system, however they must not be fitted inthe room where the room thermostat is fitted. There must be at leastone radiator installed with lock shield valves that should not be closed.Further guidance can be obtained from the Domestic Heating and HotWater Guide to the building regulations.3.8 DOMESTIC HOT WATER SYSTEM(CBX APPLIANCES ONLY)a) Check that the mains water pressure is sufficient (as stated in2.2 “Performance Data”) to produce the required DHW flow rate,but does not exceed the maximum DHW pressure (10 bar). Ifnecessary, a pressure-reducing valve must be fitted to the mainssupply before the DHW inlet connection.b) The final 600 mm (24 in) of the mains supply pipe to theboiler must be copper.c) Avoid long DHW pipe runs and several hot water draw off points.d) Insulate the hot water pipes if accessible to minimise the heatlosses within the pipes to keep the water hot longer.e) A domestic hot water regulator is fitted within the applianceto control the maximum water flow rate. This may be removed toobtain higher flow rates. Higher flow rates will not damage theappliance but may reduce the water temperature below anacceptable level.DOMESTIC HOT / COLD WATER SUPPLY TAPS ANDMIXING TAPS. All equipment designed for use at mains waterpressure is suitable.SHOWERS & BIDETS. Any mains pressure shower or bidetcomplying with the Local Water Undertaking byelaws is suitable.12PRESSURE GAUGE - A pressure gauge is situated on theappliance control panel. This can be viewed by lowering thebottom front panel.PRESSURE RELIEF VALVE - A pressure relief valve set to 3 bar(43.5 psi) is supplied with the appliance, however it will start to openat approximately 2.7 bar. It should not be used to flush the system.
7 TYPICAL SYSTEM DESIGN FOR EDEN CBX OPTIONAL SYSTEM DESIGNAPPLIANCEROOMTHERMOSTATTIMECLOCKRADIATOR WITH2 LOCKSHIELDVALVES IN OPENPOSITIONMAINSWATER INCH FLOWCH RETURNPRESSURERELIEF OUTLETTO DRAINDOMESTICHOT WATER OUTDRAIN COCK ATLOWEST POINTIN SYSTEMDOMESTICCOLD WATERDOMESTICHOT WATERGAS SUPPLYPRESSURE REDUCINGVALVE (if required)APPLIANCEBS STOP VALVE(Fixed Spindle)220V RELAY BOX(Optional)RTIMECLOCKROOMTHERMOSTATWITH UNVENTED STORAGETANK FOR EDEN SBXMAINS WATERFTANKTHERMOSTATR IIR = ReturnR II = Secondary ReturnF = FlowFor information please conatct Halstead BoilersTechnical Helpline under 01926 834834NOTE (CBX circuit): No automatic by-pass required. However it isrecommended to leave one radiator open to ensure pump over-runfunction. It is also recommended to fit TRV’s on all radiators except inrooms with a room thermostatNOTE (SBX circuit): If a hot water cylinder is fitted it isrecommended to fit a system by-pass to ensure pump over-run function.13
Page 1: EDEN X TYPECBX 24 & 32SBX 30INSTALL
Page 5 and 6: Appliance CBX32 CBX24 SBX30 CBX32 C
Page 7 and 8: 8 FLUE OPTIONS2Chimney flue liner k
Page 9 and 10: For installation details refer to t
Page 11 and 12: 4b Domestic Hot Water Mode (CBX)4c
Page 13: 5 FLUE TERMINAL POSITION•C•A•
Page 17 and 18: 4APPLIANCEINSTALLATIONBefore instal
Page 19 and 20: 4.5 GAS CONNECTIONRefer to Figure 1
Page 21 and 22: 5COMMISSIONING& TESTING5.1 FILLING
Page 23 and 24: 20INLET PRESSURE TEST POINT5.3 DHW
Page 25 and 26: 6ROUTINESERVICINGTo ensure continue
Page 27 and 28: 6.5 COMBUSTION CHAMBER &HEAT EXCHAN
Page 29 and 30: 29INTERNAL WIRING DIAGRAMS77.1 : FU
Page 31 and 32: LED CODE1 2 3 4FAULT/EFFECT REASON
Page 33 and 34: 9.3 GAS CONTROL VALVEINCLUDING AIR
Page 35 and 36: 9.6 COMBUSTION CHAMBERFRONT INSULAT
Page 37 and 38: 9.11 DIVERTER VALVE MOTORISED HEADR
Page 39 and 40: 38the manual air vent. Re-pressuris
Page 41 and 42: 541 2 3 45 6 7 89 10 11 1213 14 15

CBX 24 & 32 SBX 30 - Trademate Home Page

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?