CBX 24 & 32 SBX 30 - Trademate Home Page

More documents

Recommendations

Info

3cparticular flue kit raises the flue gas outlet point to a higherelevation with the minimum amount of changes. The flue gas ductis teed-off from the concentric part and covered by an 80 mmouter tube to protect the flue duct from freezing. The air in-takeremains at the lower level (see Figure 3d).If choosing this option then the external flue duct length should betaken into account when calculating equivalent flue length.For installation details refer to the flue kit instructions.2.5.4 KIT D VERTICAL CONCENTRIC -OUTSIDE WALL (C33) PART NO: 9560853eFig 3(c) Offset vertical flue.‘a’ measured from the boiler centre line to the centre line of theextension elbow.‘b’ measured from the centre line of the extension elbow to theunderside of the air cowl.Maximum allowable length of a + b = 8900 mm.2.5.3 KIT C: RAISED EXTERNAL FLUEOUTLET FLUE KIT (C13)3d!6If the standard horizontal terminal is likely to cause nuisance toneighbours or buildings, because of excess pluming, then thisSuitable for installations if the appliance can't be repositionedand where other horizontal flue options may cause some nuisanceto neighbours or buildings. The flue kit contains some additional45° elbows and extension ducts as well as a special wall bracketto pass the guttering (see Figure 3e). The concentric flue will berouted vertically alongside the outside wall to above the roofline.Special seals are required to prevent rainwater penetrating thepipe joints.For installation details refer to the flue kit instructions.2.6 KIT E CHIMNEY FLUE LINER KIT (B23)- PART NO. 956082This kit is suitable for open flue application in accordance withBS5440 where a room sealed flue installation is impractical. Thekit comprises of a flue adaptor from the appliance to the chimney,a flexible plastic flue liner with connection parts and chimneyterminal (see Figure 3f). Where an open flue system is used, thenan air vent must be provided in the same room or internal spaceas the flue duct air inlet, see section 3.4.
For installation details refer to the instructions provided with theopened flued kit.Maximum flue resistance permitted for an openedflued system = 100 Pa.Minimum flue resistance permitted for an openedflued system = 38 Pa.Flue ComponentFlue Resistance Part Number(Pa)Air inlet Assembly (required) 9 -60/80 Adaptor (required) 12 -Terminal (required) 9 -91.5° Elbow (80) (required) 8 -80 diameter Corrugated (required) 2/metre -80 mm diameter straight duct 2/metre -Horizontal Flue Adaptor 15 956086Vertical Flue Adaptor 0 95608793° Elbow (60/100) 15 95609145° Elbow (60/100) 7 9560903fChimney flue liner kit - Part no. 956082Chimney terminal2.7 KIT F: SPLIT PIPE VERTICAL FLUEOUTLET (C53) - PART NO. 956080This flue system kit is designed for installations where the air intake position isdifferent from the flue duct exit point. The kit comprises a twin adaptor fromthe which the air intake is taken from the adjacent outside wall (see exampleFigure 3g) and the flue duct is routed vertically through the roof.It has to be noted that the flue duct is under pressure when the appliance isin operation and the duct can leak poisonous carbon monoxide if the ductcomponents are not correctly assembled. It is not recommended to route theflue duct through living space areas, i.e. bed rooms, living rooms etc.For C5 flue systems the terminals for the supply of combustion air and for theevacuation of combustion products shall not be installed on opposite walls ofthe building.For installation details refer to the instructions provided with the twin flued kit.Maximum flue resistance permitted for a twin fluedsystem = 120 PaMinimum flue resistance permitted for a twin fluedsystem = 66 PaFlue Component Flue Resistance (Pa) Part NumberTwin Flue Adaptor (required) 30 -Air Inlet Terminal (required) 9 -Flue Outlet Terminal (required) 27 -80 mm diameter straight duct 2/metre 95610290° Elbow (80/80) 8 95610045° Elbow (80/80) 4 956099!In replacement installations,the chimney has to becleared of debris andall flue parts.Centralising brackets93 flanged elbow (concentric)with sampling pointFlexible corrugated plastic flue linerØ80mm according to EN 14471Max. length 30m.Min. length 5m.3gSplit pipe verticalflue outlet kit -Part no. 956080The flue resistance for thefollowing accessories hasto be considered.Ø80mm flue extension90 elbow45 elbowMax. flue length 30m.If the flue pipe passesthrough habitable roomswithin the same dwelling,the flue pipe must berouted through ventedair ducts.! !Roof terminal with pitchedroof flashing kit.If the flue pipe passesthrough compartmentfrom wall/floors, therequirements set outin Building RegulationsPart B must be followed.ChimneyplateØ60/100mm concentricchimney adaptor pipe.Ø80mm twin adaptorwith sampling point.Ø80mm air intakeKIT EA flue system can be built up from the componentsdetailed in the table, but the total flue resistance mustnot exceed the maximum stated.Split flue systemKit FA flue system can be built up from the componentsdetailed in the table, but the total flue resistance mustnot exceed the maximum stated.7
Page 1: EDEN X TYPECBX 24 & 32SBX 30INSTALL
Page 5 and 6: Appliance CBX32 CBX24 SBX30 CBX32 C
Page 7: 8 FLUE OPTIONS2Chimney flue liner k
Page 11 and 12: 4b Domestic Hot Water Mode (CBX)4c
Page 13 and 14: 5 FLUE TERMINAL POSITION•C•A•
Page 15 and 16: 7 TYPICAL SYSTEM DESIGN FOR EDEN CB
Page 17 and 18: 4APPLIANCEINSTALLATIONBefore instal
Page 19 and 20: 4.5 GAS CONNECTIONRefer to Figure 1
Page 21 and 22: 5COMMISSIONING& TESTING5.1 FILLING
Page 23 and 24: 20INLET PRESSURE TEST POINT5.3 DHW
Page 25 and 26: 6ROUTINESERVICINGTo ensure continue
Page 27 and 28: 6.5 COMBUSTION CHAMBER &HEAT EXCHAN
Page 29 and 30: 29INTERNAL WIRING DIAGRAMS77.1 : FU
Page 31 and 32: LED CODE1 2 3 4FAULT/EFFECT REASON
Page 33 and 34: 9.3 GAS CONTROL VALVEINCLUDING AIR
Page 35 and 36: 9.6 COMBUSTION CHAMBERFRONT INSULAT
Page 37 and 38: 9.11 DIVERTER VALVE MOTORISED HEADR
Page 39 and 40: 38the manual air vent. Re-pressuris
Page 41 and 42: 541 2 3 45 6 7 89 10 11 1213 14 15

CBX 24 & 32 SBX 30 - Trademate Home Page

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?