EN 14766:2005 - 64_e_stf - Baltik vairas

More documents

Recommendations

Info

EN 14766:2005 (E)Dimension in millimetresKey1 Water nozzles2 Front hub3 Flexible pipe4 Suspension-fork leg5 Y-joint6 Brake disc7 Disc-brake calliper8 Direction of wheel rotationFigure 12 — Water-nozzles for disc-brake (front)24
EN 14766:2005 (E)Dimension in millimetresKey1 Water-nozzles2 Rear frame3 Rear hub4 Y-joint5 Brake disc6 Disc-brake calliper7 Direction of wheel rotationFigure 13 — Water-nozzles for disc-brake (rear)4.6.7.5.1.7 Test method – test runs under wet conditionsThe method shall be as given in 4.6.7.5.1.6, with the addition that wetting of the brake system(s) shall commencenot less than 25 m prior to the commencement of braking (3.11) and shall continue until the bicycle comes to rest.NOTEExcessive amounts of water may be swept from the test-track surface between runs.4.6.7.5.1.8 Number of valid test runsI) If the gradient of the track is less than 0,2 %, the following runs shall be made:a) five consecutive valid runs under dry conditions;b) two acclimatization runs under wet conditions (results not recorded);c) five consecutive valid runs under wet conditions.II)If the gradient of the track lies between 0,2 % and 0,5 %, the following runs shall be made:a) six consecutive valid runs under dry conditions with alternate runs in opposite directions;b) two acclimatisation runs under wet conditions (results not recorded);c) six consecutive valid runs under wet conditions with alternate runs in opposite directions.25
Page 11: EN 14766:2005 (E)Foam pads attached
Page 16 and 17: EN 14766:2005 (E)4.6.5 Brake adjust
Page 18 and 19: EN 14766:2005 (E)4.6.7.5 Test metho
Page 20 and 21: EN 14766:2005 (E)Key1 Water-nozzles
Page 22 and 23: EN 14766:2005 (E)Key1 Water nozzles
Page 26 and 27: EN 14766:2005 (E)NOTEA rest period
Page 28 and 29: EN 14766:2005 (E)4.6.7.5.2.4 Test m
Page 30 and 31: EN 14766:2005 (E)Keyα = 90° to 12
Page 32 and 33: EN 14766:2005 (E)IV) Correction of
Page 34 and 35: EN 14766:2005 (E)A maximum of ten i
Page 36 and 37: EN 14766:2005 (E)4.7.6.1.2 Requirem
Page 38 and 39: EN 14766:2005 (E)Dimension in milli
Page 40 and 41: EN 14766:2005 (E)4.7.6.4 Handlebar
Page 44 and 45: EN 14766:2005 (E)4.7.7.4 Requiremen
Page 46 and 47: EN 14766:2005 (E)Manufacturers of f
Page 50 and 51: EN 14766:2005 (E)Dimensions in mill
Page 52 and 53: EN 14766:2005 (E)Keyd 1 ≤ 2dd 2
Page 54 and 55: EN 14766:2005 (E)NOTE See also 4.10
Page 56 and 57: EN 14766:2005 (E)Key1 Low-mass roll
Page 58 and 59: EN 14766:2005 (E)Key1 Pivoted force
Page 62 and 63: EN 14766:2005 (E)4.10 Wheels and wh
Page 64 and 65: EN 14766:2005 (E)4.10.4.3 Rear whee
Page 66 and 67: EN 14766:2005 (E)4.12.3 Stage 2: Te
Page 68 and 69: EN 14766:2005 (E)4.13.3 Pedal/pedal
Page 70 and 71: EN 14766:2005 (E)Key1 Pedal2 Test-s
Page 72 and 73: EN 14766:2005 (E)spindle falls to 5
Page 74 and 75:
EN 14766:2005 (E)4.14.3 Seat-pillar
Page 76 and 77:
EN 14766:2005 (E)Keya) Force under
Page 78 and 79:
EN 14766:2005 (E)Dimension in milli
Page 80 and 81:
EN 14766:2005 (E)Dimension in milli
Page 82 and 83:
EN 14766:2005 (E)r) appropriate spa
Page 84 and 85:
EN 14766:2005 (E)Annex A(informativ
Page 86 and 87:
EN 14766:2005 (E)KeyY Braking force
Page 88 and 89:
EN 14766:2005 (E)Key1 Direction of
show all

EN 14766:2005 - 64_e_stf - Baltik vairas

Create successful ePaper yourself

Delete template?

Save as template?