EN 14766:2005 - 64_e_stf - Baltik vairas

More documents

Recommendations

Info

EN 14766:2005 (E)4.7.7.4 Requirement for stage 2When tested by the method described in 4.7.7.5, there shall be no visible cracks or fractures in any part of thehandlebar and stem assembly.For carbon-fibre handlebars or stems, the peak deflection during the test in direction from the mean position shallnot increase by more than 20 % of the initial values.4.7.7.5 Test method for stage 2Apply fully-reversed forces of 450 N at a position 50 mm from the free end each side of the handlebar for100 000 cycles, with the forces at each end of the handlebar being in phase with each other and parallel to the axisof the handlebar stem as shown in Figure 25 b). The maximum test frequency shall be 25 Hz.4.8 Frames4.8.1 Suspension-frames – special requirementsThe design shall be such that if the spring or damper fails, the tyre shall not contact any part of the frame nor shallthe assembly carrying the rear wheel become detached from the rest of the frame.44
EN 14766:2005 (E)Dimensions in millimetresKey1 Wheel-base2 Permanent set3 22,5 kg striker4 360 mm drop height5 Low mass roller (1 kg max.)6 Rigid mounting for rear axle attachment pointFigure 27 — Frame and front fork assembly – impact test (falling mass)4.8.2 Frame and front fork assembly – impact test (falling mass)4.8.2.1 GeneralManufacturers of complete bicycles shall conduct the test with the frame fitted with the appropriate front fork and, ifthis is a suspension-fork it shall be at its unloaded length.45
Page 11: EN 14766:2005 (E)Foam pads attached
Page 16 and 17: EN 14766:2005 (E)4.6.5 Brake adjust
Page 18 and 19: EN 14766:2005 (E)4.6.7.5 Test metho
Page 20 and 21: EN 14766:2005 (E)Key1 Water-nozzles
Page 22 and 23: EN 14766:2005 (E)Key1 Water nozzles
Page 24 and 25: EN 14766:2005 (E)Dimension in milli
Page 26 and 27: EN 14766:2005 (E)NOTEA rest period
Page 28 and 29: EN 14766:2005 (E)4.6.7.5.2.4 Test m
Page 30 and 31: EN 14766:2005 (E)Keyα = 90° to 12
Page 32 and 33: EN 14766:2005 (E)IV) Correction of
Page 34 and 35: EN 14766:2005 (E)A maximum of ten i
Page 36 and 37: EN 14766:2005 (E)4.7.6.1.2 Requirem
Page 40 and 41: EN 14766:2005 (E)4.7.6.4 Handlebar
Page 46 and 47: EN 14766:2005 (E)Manufacturers of f
Page 50 and 51: EN 14766:2005 (E)Dimensions in mill
Page 52 and 53: EN 14766:2005 (E)Keyd 1 ≤ 2dd 2
Page 54 and 55: EN 14766:2005 (E)NOTE See also 4.10
Page 56 and 57: EN 14766:2005 (E)Key1 Low-mass roll
Page 58 and 59: EN 14766:2005 (E)Key1 Pivoted force
Page 62 and 63: EN 14766:2005 (E)4.10 Wheels and wh
Page 64 and 65: EN 14766:2005 (E)4.10.4.3 Rear whee
Page 66 and 67: EN 14766:2005 (E)4.12.3 Stage 2: Te
Page 68 and 69: EN 14766:2005 (E)4.13.3 Pedal/pedal
Page 70 and 71: EN 14766:2005 (E)Key1 Pedal2 Test-s
Page 72 and 73: EN 14766:2005 (E)spindle falls to 5
Page 74 and 75: EN 14766:2005 (E)4.14.3 Seat-pillar
Page 76 and 77: EN 14766:2005 (E)Keya) Force under
Page 82 and 83: EN 14766:2005 (E)r) appropriate spa
Page 84 and 85: EN 14766:2005 (E)Annex A(informativ
Page 86 and 87: EN 14766:2005 (E)KeyY Braking force
Page 88 and 89: EN 14766:2005 (E)Key1 Direction of

EN 14766:2005 - 64_e_stf - Baltik vairas

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?