EN 14766:2005 - 64_e_stf - Baltik vairas

More documents

Recommendations

Info

EN 14766:2005 (E)KeyY Braking force, NX Input force, N1 + 20 % limit2 Line of best fit3 -20 % limitFigure A.1 — Graph of input force against braking force, showing line of best fit and ± 20 % limit lines86
EN 14766:2005 (E)Annex B(informative)Steering geometryThe steering geometry employed, as shown in Figure B.1, will generally be dictated by the use for which the bicycleis intended but it is nevertheless recommended that:a) the steering head angle be not more than 75° and not less than 65° in relation to the ground line, andb) the steering axis intersects a line perpendicular to the ground line, drawn through the wheel centre, at apoint not lower than 15 % and not higher than 60 % of the wheel radius when measured from the groundline.87
Page 11:
EN 14766:2005 (E)Foam pads attached
Page 16 and 17:
EN 14766:2005 (E)4.6.5 Brake adjust
Page 18 and 19:
EN 14766:2005 (E)4.6.7.5 Test metho
Page 20 and 21:
EN 14766:2005 (E)Key1 Water-nozzles
Page 22 and 23:
EN 14766:2005 (E)Key1 Water nozzles
Page 24 and 25:
EN 14766:2005 (E)Dimension in milli
Page 26 and 27:
EN 14766:2005 (E)NOTEA rest period
Page 28 and 29:
EN 14766:2005 (E)4.6.7.5.2.4 Test m
Page 30 and 31:
EN 14766:2005 (E)Keyα = 90° to 12
Page 32 and 33:
EN 14766:2005 (E)IV) Correction of
Page 34 and 35:
EN 14766:2005 (E)A maximum of ten i
Page 36 and 37: EN 14766:2005 (E)4.7.6.1.2 Requirem
Page 38 and 39: EN 14766:2005 (E)Dimension in milli
Page 40 and 41: EN 14766:2005 (E)4.7.6.4 Handlebar
Page 44 and 45: EN 14766:2005 (E)4.7.7.4 Requiremen
Page 46 and 47: EN 14766:2005 (E)Manufacturers of f
Page 50 and 51: EN 14766:2005 (E)Dimensions in mill
Page 52 and 53: EN 14766:2005 (E)Keyd 1 ≤ 2dd 2
Page 54 and 55: EN 14766:2005 (E)NOTE See also 4.10
Page 56 and 57: EN 14766:2005 (E)Key1 Low-mass roll
Page 58 and 59: EN 14766:2005 (E)Key1 Pivoted force
Page 62 and 63: EN 14766:2005 (E)4.10 Wheels and wh
Page 64 and 65: EN 14766:2005 (E)4.10.4.3 Rear whee
Page 66 and 67: EN 14766:2005 (E)4.12.3 Stage 2: Te
Page 68 and 69: EN 14766:2005 (E)4.13.3 Pedal/pedal
Page 70 and 71: EN 14766:2005 (E)Key1 Pedal2 Test-s
Page 72 and 73: EN 14766:2005 (E)spindle falls to 5
Page 74 and 75: EN 14766:2005 (E)4.14.3 Seat-pillar
Page 76 and 77: EN 14766:2005 (E)Keya) Force under
Page 82 and 83: EN 14766:2005 (E)r) appropriate spa
Page 84 and 85: EN 14766:2005 (E)Annex A(informativ
Page 88 and 89: EN 14766:2005 (E)Key1 Direction of
show all

EN 14766:2005 - 64_e_stf - Baltik vairas

Create successful ePaper yourself

Delete template?

Save as template?