EN 14766:2005 - 64_e_stf - Baltik vairas

More documents

Recommendations

Info

EN 14766:2005 (E)Dimension in millimetresKey1 Rigid mount incorporating head bearings2 Brake mounting-point3 Test adaptorFigure 37 — Fork for hub/disc-brake – repeated brake-torque test4.9.7.3.2 Test methodMount the fork in a fixture representative of the head-tube and gripped in the normal head-bearings with the axis ofthe fork-stem vertical. Fit an axle to the fork, and mount on the axle a pivoted, straight adaptor as shown inFigure 37 to provide a torque-arm of 330 mm in length and a suitable attachment for the brake mounting-point.Apply repeated, horizontal, dynamic forces of 600 N rearward to the end of the torque-arm parallel to the plane ofthe wheel (as shown in Figure 37) for 12 000 test cycles with a test frequency not exceeding 25 Hz.60
EN 14766:2005 (E)Keya) Rim with tyreb) Rim without tyre1 Dial-gauge (concentricity)2 Instrument stand3 Hub axle support4 Dial-gauge (lateral run-out)5 Instrument stand6 Rim with tyre7 Rim without tyre8 Dial gauge (concentricity)(alternative position)9 Instrument standFigure 38 — Wheel/tyre assembly – rotational accuracy61
Page 11: EN 14766:2005 (E)Foam pads attached
Page 16 and 17: EN 14766:2005 (E)4.6.5 Brake adjust
Page 18 and 19: EN 14766:2005 (E)4.6.7.5 Test metho
Page 20 and 21: EN 14766:2005 (E)Key1 Water-nozzles
Page 22 and 23: EN 14766:2005 (E)Key1 Water nozzles
Page 24 and 25: EN 14766:2005 (E)Dimension in milli
Page 26 and 27: EN 14766:2005 (E)NOTEA rest period
Page 28 and 29: EN 14766:2005 (E)4.6.7.5.2.4 Test m
Page 30 and 31: EN 14766:2005 (E)Keyα = 90° to 12
Page 32 and 33: EN 14766:2005 (E)IV) Correction of
Page 34 and 35: EN 14766:2005 (E)A maximum of ten i
Page 36 and 37: EN 14766:2005 (E)4.7.6.1.2 Requirem
Page 40 and 41: EN 14766:2005 (E)4.7.6.4 Handlebar
Page 44 and 45: EN 14766:2005 (E)4.7.7.4 Requiremen
Page 46 and 47: EN 14766:2005 (E)Manufacturers of f
Page 50 and 51: EN 14766:2005 (E)Dimensions in mill
Page 52 and 53: EN 14766:2005 (E)Keyd 1 ≤ 2dd 2
Page 54 and 55: EN 14766:2005 (E)NOTE See also 4.10
Page 56 and 57: EN 14766:2005 (E)Key1 Low-mass roll
Page 58 and 59: EN 14766:2005 (E)Key1 Pivoted force
Page 62 and 63: EN 14766:2005 (E)4.10 Wheels and wh
Page 64 and 65: EN 14766:2005 (E)4.10.4.3 Rear whee
Page 66 and 67: EN 14766:2005 (E)4.12.3 Stage 2: Te
Page 68 and 69: EN 14766:2005 (E)4.13.3 Pedal/pedal
Page 70 and 71: EN 14766:2005 (E)Key1 Pedal2 Test-s
Page 72 and 73: EN 14766:2005 (E)spindle falls to 5
Page 74 and 75: EN 14766:2005 (E)4.14.3 Seat-pillar
Page 76 and 77: EN 14766:2005 (E)Keya) Force under
Page 82 and 83: EN 14766:2005 (E)r) appropriate spa
Page 84 and 85: EN 14766:2005 (E)Annex A(informativ
Page 86 and 87: EN 14766:2005 (E)KeyY Braking force
Page 88 and 89: EN 14766:2005 (E)Key1 Direction of

EN 14766:2005 - 64_e_stf - Baltik vairas

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?