analogue signal conditioning waveseries·microseries·mcz-series

Current MonitoringWAVECONTROL• input and output rangeadjustable by DIP switch• no calibration required• true TRMS value measurements• hall sensor measurementmethodWAS2 CMAWAZ2 CMA5/10A ac/dcselectable withanalogue output0 ... 20 mA/4 ... 20 mA/0 ... 10 VWAS2 CMAWAZ2 CMA20/25/30A ac/dcselectable withanalogue output0 ... 20 mA/4 ... 20 mA/0 ... 10 VApprovals:% {Schematic circuit diagramOrdering dataScrew connectionTension clamp connectionTechnical data*InputInput currentInput frequencyAccuracyMeasuring principleConnection typePass through diameterMeasurement circuit voltageMax. measuring circuitOutputCurrent/voltage selectableOutput voltageOffset voltageLoad resistanceOutput signal limitOutput currentOffset currentLoad resistanceStatus LEDTemperature coefficientResponse time (10 ... 90%)Coordination of insulation according to DIN EN 50178, 04/98(safe separation)Rated voltgeRated surge voltageOvervoltage categoryContamination classClearance and creepage distanceTest voltageGeneral DataSupplySupply voltagePower consumption at rated voltageReverse polarity protectionType Part No. Qty.WAS2 CMA 5/10A uc 8526610000 1WAZ2 CMA 5/10A uc 8526620000 15 A uc/10 A uc selectable (without additional adjustment)0 Hz - 2 kHz (True RMS to DC Converter)1% (0 Hz - 1 kHz) Crest factor 3 FSR2% (0 Hz - 2 kHz) Crest factor 5 FSRContact-free current monitoring using Hall sensorPush-through connection(Please notice push through direction by DC measurement)8 mm400 Vac, higher voltages dependenton wire insulationdependent on wire cross-section0 ... 10 V0 ... 20 mA4 ... 20 mA0 ... 10 Vmax. 0.08 V≥1 KΩapprox. 13 V and. 24 mA0/4 ... 20 mAmax.150 µA≤ 600 Ωgreen LEDON–> OK; blinks –> signal out of range; OFF –> Error≤ 650 ppm/Ktyp. 700 ms300 V6 KVlll2≥ 5.5 mm4 kV eff21.6 Vdc...24 Vdc...26.4 Vdc50 mA at I out = 20 mAyesType Part No. Qty.WAS2 CMA 20/25/30A uc 8545830000 1WAZ2 CMA 20/25/30A uc 8545840000 120/25/30 A uc selectable (without additional adjustment)0 Hz - 2 kHz (True RMS to DC Converter)1% (0Hz - 1KHz) Crest factor 3 FSR2% (0Hz - 2KHz) Crest factor 5 FSRContact-free current monitoring using Hall sensorPush-through connection(Please notice push through direction by DC measurement)8 mm400 Vac, higher voltages dependenton wire insulationdependent on wire cross-section0 ... 10 V0 ... 20 mA4 ... 20 mA0 ... 10 Vmax. 0.08 V≥1 KΩapprox. 13 V and. 24 mA0/4 ... 20 mAmax.150 µA≤ 600 Ωgreen LEDON–> OK; blinks –> signal out of range; OFF –> Error≤ 650 ppm/Ktyp.700 ms300 V6 KVlll2≥ 5.5 mm4 kV eff21.6 Vdc...24 Vdc...26.4 Vdc50 mA at I out = 20 mAyesOperating temperature rangeStorage/transportFactory settingDimensions L/H/W (mm)WeightApprovals* T U = 23 °C single module0 ... 50 ºC-20 ... +70 ºC0 ... 5A uc; 4 ... 20 mA92.4/112.4/22.5150 gCE, cUL0 ... 50 ºC-20 ... +70 ºC0 ... 25 A uc; 4 ... 20mA92.4/112.4/22.5150gCE, cUL54