SRL3 Rodless cylinder - CKD

More documents

Recommendations

Info

1. Position locking type SRL3-QWARNINGFor safety purposes, prevent the load from droppingunder its own weight during maintenance.When using the cylinder with air cushion, if the aircushion needle on the lock mechanism side is tootight, the piston could bounce at the stroke end causingthe lock lever and lock pin to collide and damagethe locking mechanism. If the air cushion needle isopened too far, the piston could spring back at thestroke end and cause similar damage. Adjust the aircushion needle so that the piston does not bounce.When stopping with an external shock absorber, etc.,adjust in the same way to prevent bouncing.Regularly (once or twice a year) check that the holdingsection is not damaged by this symptom.CAUTIONIf the locking mechanism has been manually operated,check and then return it manually to the originalposition.Do not use a manual override exceptduring adjustment.Release the lock when installing or adjusting the cylinder.The lock could be damaged if the cylinder isinstalled while the lock is applied.Do not use multiple cylinders synchronized. Do notmove more than one workpiece using more than twocylinders with position locking mechanism simultaneously.One of the cylinders may become unable tounlock.Use the speed control valve with meter-out control.Locks may not be released during meter-in control.Always use up to the stroke end of the side with thelock. If the cylinder's piston does not reach the strokeend, the lock may not be applied or may not be released.Apply grease to sliding section of lock lever periodically.During Use & Maintenance2. Full cowling type SRL3-JCAUTIONSuspended particles such as fiber, feathers, or powdermay pass through the table adapter passage underthe cover and adhere to the cylinder, leading tooperation faults.If coolant (oil) or cutting chips scatter with force, or ifthey scatter from an inclined direction, provide anothercover on the cylinder and sides, etc.Do not let particles get stuck in the clearance of 2 to3mm between the sliding section(table adaptor) andthe cover.Regularly remove particles on top of the cover and inside thecover. The product may be damaged if this is left as is.This product provides clearance under the cover for passingthe table adapter through. Therefore, there is a risk of particlesentering the cover.Do not get on the cover. It could break.SRL3 SeriesSpecific precautionsSCP*2CMK2CMA2SCMSCGSCA2SCSCKV2CA/OV2SSDCATMDC2MVCSMD2MSD*FC*STKULK*JSK/M2JSGJSC3USSDUSCJSB3LMBSTGSTS LLCSLCGLCMLCTLCYSTR2UCA2HCMHCASRL3SRG3SRM3SRT3MRL2MRG2SM-25CAC4UCAC2RCC2MFCSHCGLCEndingRodless typeRodless cylinder2003
SCP*2CMK2CMA2SCMSCGSCA2SCSCKV2CA/OV2SSDCATMDC2MVCSMD2MSD*FC*STKULK*JSK/M2JSGJSC3USSDUSCJSB3LMBSTGSTS LLCSLCGLCMLCTLCYSTR2UCA2HCMHCASRL3SRG3SRM3SRT3MRL2MRG2SM-25CAC4UCAC2RCC2MFCSHCGLCEndingSpecificationsDescriptionsBore sizeActuationWorking fluidMax. working pressureMin. working pressureWithstanding pressureAmbient temperaturePort sizeStroke toleranceWorking piston speedCushionLubricationmmMPaMPaMPammmm/sSRL3ø12 ø16 ø20 ø25 ø32 ø40 ø50 ø63 ø80Double actingCompressed air0.70.2 0.10.051.055 to 60M5Rc 1 /8Rc 1 /4Rc 3 /8+ 2.0 + 2.50 (up to 1000), 0 (up to 3000), (up to 5000)Rc 1 /2ø10050 to 2000 (standard port piping) (note 1)Air cushionNot required (continuously lubricate using turbine oil class 1 ISOVG32 if lubricated.)Note 1: Piston speed used with common port piping differs depending on the stroke. Contact CKD for details.Allowable energy absorptionBore size(mm)ø12ø16ø20ø25ø32ø40ø50ø63ø80ø100CushionedNo cushionAllowable energy absorption (J) Cushion mm stroke (mm) Allowable energy absorption (J) Absorbed energy (J) Valid mm stroke (mm)0.030.220.591.402.574.279.1317.4406714.519.222.220.923.523.924.929.645.845.80.0030.0070.0100.0150.0300.0500.0720.1380.3930.6222.42.45.710185086861431435.55.5791316.521212525Note: The minimal stroke for full stroke adjustment models with switches are shown in ( ).+ 3.00With shock absorber (initial setpoint)M type switch quantity and min. stroke length (mm)Switch quantitySwitch model no.Bore size (mm)M*V1M*Hø1210 10 30 45(70) 60 90(120)ø1610 10 30 45(70) 60 90(120)ø2010 10 30 45(70) 60 90(120)ø2510 10 30 45(70) 60 90(120)ø3210 10 30 45 60 90ø4010 10 30 45 60 90ø5015 15 30 45 60 90ø6315 15 30 45 60 90ø802550100ø1002550100Note: The minimal stroke for full stroke adjustment models with switches are shown in ( ).Switch quantitySwitch model no.Bore size (mm)ø12ø16ø20ø25ø32ø40ø50ø63ø80ø100T*V555101010101015151T*H55510101010101515Rodless cylinderSRL3 SeriesBore size :JIS symbolM*V2M*HM*VT type switch quantity and min. stroke length (mm)T*V454545454545454545452T*H50(70)50(70)50(70)50(70)505050505050T*V85858585858585858585ø12, ø16, ø20, ø25, ø32ø40, ø50, ø63, ø80, ø10033M*HT*H100(120)100(120)100(120)100(120)100100100100100100Stroke lengthBore size(mm)ø12ø16ø20ø25ø32ø40ø50ø63ø80ø100M*V9090909090909090T*V12512512512512512512512512512541501504M*H135(170)135(170)135(170)135(170)135135135135T*H150(170)150(170)150(170)150(170)150150150150150150Standard stroke length(mm)200,300400,500600,700800,9001000M*V5Max. stroke length(mm)M*H5000120 180(220)120 180(220)120 180(220)120 180(220)120 180120 180120 180120 180200200T*V1651651651651651651651651651655T*H200(220)200(220)200(220)200(220)200200200200200200M*VMin. stroke length(mm)** The intermediate stroke can be manufactured in 1 mm increments.6M*H150 225(270)150 225(270)150 225(270)150 225(270)150 225150 225150 225150 225250250T*V20520520520520520520520520520561T*H250(270)250(270)250(270)250(270)2502502502502502502004
Page 1 and 2: Rodless typeOverviewHigh load and l
Page 4 and 5: SRL3 G Q LB 20Model no.A Mounting s
Page 6 and 7: 1. CommonHow to adjust stroke adjus
Page 8 and 9: SRL3 SeriesSpecific precautionsBore
Page 12 and 13: Switch specifications (M type switc
Page 14 and 15: Option combination table: Combinati
Page 16 and 17: SRL3 SeriesInternal structure and p
Page 18 and 19: Internal structure and parts listPa
Page 20 and 21: Dimensions (ø12 to ø20)SRL3 with
Page 30 and 31: Internal structure drawing and part
Page 32 and 33: SRL3-G SeriesInternal structure and
Page 34 and 35: Dimensions (ø12 to ø20)SRL3-G wit
Page 36 and 37: Dimensions (ø25 to ø63)SRL3-G-LB-
Page 38 and 39: Dimensions (ø80 to ø100)SRL3-G-LB
Page 48 and 49: Dimensions (ø80, ø100)SRL3-QQJQKS
Page 54 and 55: Internal structure and parts listRe
Page 56 and 57: SRL3 series common dimensions: Opti
Page 58 and 59: SRL3 series common dimensions: Opti
Page 60 and 61:
Switch12345Switch body + mounting b
Page 62 and 63:
Floating joint setFloating joint se
Page 64 and 65:
Rodless cylinder SRL3-J SeriesFull
Page 66 and 67:
Switch specifications (M type switc
Page 68 and 69:
How to order switchSwitch body + mo
Page 70 and 71:
Internal structure and parts list (
Page 72 and 73:
SRL3-J SeriesInternal structure and
Page 74 and 75:
Dimensionsø25 (with switch)SRL3-J-
Page 76 and 77:
Dimensionsø32 to 63 (with switch)S
Page 78 and 79:
SRL3-J SeriesDouble acting/full cow
Page 80 and 81:
Dimensions: extension fittingAdjust
Page 82 and 83:
SRL3 SeriesSelection guide3 Obtain
Page 84 and 85:
Confirm the composite moment (MT) w
Page 86 and 87:
1 Restriction of vertical load2 Ben
Page 88 and 89:
SRL3 SeriesSelection guideInclinati
show all

SRL3 Rodless cylinder - CKD

Create successful ePaper yourself

Delete template?

Save as template?