XC1008D-XC1011D - Emerson Climate Technologies

More documents

Recommendations

Info

EX.3 compressors, 1 frequency compressor,C1 = FRQ1 C37 = db 1Q8 = 100C2 = CPR1 1Q2 = CPRC3 = CPR1 1Q7 = 100where1Q6 Minimum value for analog out.1 0 ÷ 100 %1Q12 Regulation delay after entering the regulation band 0 ÷ 255 (sec)1Q14 Analog output 1 permanency at 100% before load activation 0 ÷ 255 (sec)1Q15 Delay between pressure (temperature) goes down the set point and start of 0 ÷ 255 (sec)analog output 1 decreasingCP11 2 different load start delay 0 ÷ 99.5 (min.1sec)CP12 2 different load off delay 0 ÷ 99.5 (min.1sec)1592021021 XC1008-1011-1015D GB A5 r.1.5A 12.10.2009 XC1008-1011-1015D 48/66
9.2 Fans management with inverter– 1 fans group with invertermode, others ON in on/off modeWith this configuration, one analog output can be used to drive the inverter (1Q2 or 2Q1 or 3Q2 or4Q1 = FAN or FAN2). Set the first fans relay as inverter (FRQ1F or FRQ2F), and other relays asfans (FAN1 or FAN2).ES.: 4 fans, 1 with inverter. Analog output 1 drives the inverterC1 = FRQ1FC2 = FAN1C3 = FAN1C4 = FAN11Q2 = FAN1Q6 Minimum value for analog output 1 0 ÷ 100 %1Q7 Analog output 1 value after fan activation 1Q6 ÷ 100 %1Q8 Analog output 1 value after fan deactivation 1Q6 ÷ 100 %1Q12 Regulation delay of analog output 1 when the pressure is in the regulation band 0 ÷ 255 (sec)1Q13 Analog output 1 rise time from 1Q6 to 100% when the pressure is outside the 0 ÷ 255 (sec)regulation band1Q14 Analog output 1 permanency at 100% before load activation 0 ÷ 255 (sec)1Q16 Analog output 1 decreasing time from 100% to 1Q6 0 ÷ 255 (sec)1Q17 Analog output 1 permanency at 1Q6 before a fan is switched off with pressure below 0 ÷ 255 (sec)the set1Q18 Analog output 1 decreasing time, from 100% to 1Q7 before a load is switched on 0 ÷ 255 (sec)9.3 Management of all fans with inverter – proportional inverterIn this case all fans of the condensing group are driven by one inverter.The power used by the inverter is proportional to the delivery pressure value.Set one relay as inverter (FRQ1F or FRQ2F) and set the analog output 3 or 4 to drive it (3Q2 or4Q1 = INVF1 or INVF2).The reference probe is the probe set on parameter 3Q3 or 4Q2 = PBC3 or PBC4, respectively thedelivery probe circuit 1 and 2.The analog output is managed in proportional mode according to the pressure/temperature betweenthe SETF and the SETF1 + 3Q19 (or 4Q18).1592021021 XC1008-1011-1015D GB A5 r.1.5A 12.10.2009 XC1008-1011-1015D 49/66
Page 1 and 2: XC1008D-XC1011D-XC1015D and VGC810(
Page 3 and 4: 9.2 FANS MANAGEMENT WITH INVERTER-
Page 5 and 6: 2. Wiring connections2.1 XC1008DNOT
Page 7 and 8: 2.3 XC1015DNOTE: according to the m
Page 9: 88 - 103 and 106 - 119 Relay config
Page 13 and 14: 5. Push the ENTER key to enter in P
Page 15 and 16: 4. SERVICE MENUThe service menu col
Page 17 and 18: This outputs can be used to drive a
Page 19 and 20: 4.5.5 How to erase the running hour
Page 21 and 22: 5. Set the day by means of the UP a
Page 23 and 24: 5.3 Active alarm log menuPush the L
Page 25 and 26: C8 = FAn1;C9 = FAn1;C10 = FAn1;C11
Page 27 and 28: C46CINT: °C with decimal point (ba
Page 29 and 30: otA2 = for the optimization of the
Page 31 and 32: 6.1.8 Compressor Action (CP1-CP8)CP
Page 33 and 34: AC3 Low pressure (temperature) alar
Page 35 and 36: 1. with AUX temper. < O3 ==> “Rea
Page 37 and 38: Pbc1= Suction Probe, circuit 1 (ter
Page 39 and 40: 6.1.20 Analog Output 3 (3Q2-3Q26)3Q
Page 41 and 42: 4Q20 Band offset (-12.0÷12.0°C -1
Page 43 and 44: 7.2 Proportional band adjustment -
Page 45 and 46: 8. SCREW COMPRESSORSLoads activatio
Page 47: 9. ANALOG OUTPUTS FOR INVERTER9.1 C
Page 51 and 52: 10.1 Alarm conditions - summary tab
Page 53 and 54: 11. Configuration errorsError N. Pa
Page 55 and 56: 12.2 VG810 dimensions and mounting1
Page 57 and 58: Case: 175x132 mm; depth 60 mm.Mount
Page 59 and 60: NomeXC1008DXC1011DXC1015DLevel Desc

XC1008D-XC1011D - Emerson Climate Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?