Phase 4 â Wire L.T. Solid State ( Static) Whole Current ... - WBSEDCL

More documents

Recommendations

Info

meter is to be installed in the Meter Box and the Box in assembled condition shall haveprovision to fix it on wall. The 4 no. self threaded screws of min. size of 4 mm dia and 25 mmlong shall be provided with each Meter Box.Marking / Embossing :The following information shall be clearly & indelibly embossed (not printed) on the cover andbase of the Meter Box. The top & bottom corner of Meter Box Sl.No. shall be same for theparticular Meter Boxi) Property of WBSEDCLii) Name / Brand name of Manufactureriii) Meter Box Sl.Nos. (Embossed on both the base & covers of Meter Box)iv) Sign of dangerDrawing :Detailed dimensional drawing showing clearly the dimensions & material for Meter Box and itsconstructional features have been furnished with the tender specification which is binding onthe part of the manufacturer.Submission of Sample :Bidder shall submit a sample Meter Box as per our specification (or, as available with Bidder,however in the event of order it will be as per Specification before first inspection) along withthe sample meter to the office of the Chief Engineer, (DTD), Abhikshan Bhavan, Sector-V,Salt Lake, Kolkata-91 before the last day of submission of bid.Submission of sample meter box as per size available with the bidder but conforming to ourspecification towards its quality is acceptable . Type testing including material identification (IRSpectrometry test) of one meter box manufactured as per specification is to be conducted atany NABL accredited laboratory/CIPET by the supplier at their own cost after placement oforder. For type testing the meter box will be selected from the first offered lot of meter withmeter box. If the type test results are not found satisfactory, the offered lot of meter along withmeter box will be rejected.Testing :a) Type Test : The Meter Box offered shall be type tested as per relevant I.S. standards andthe Technical Specification stated below :The bidder must furnish type test report including material verification of the offered /samplemeter box from any NABL/Govt. approved laboratory as available with them along withtechnical bid without which the offer will not be considered. Type test report should not bemore than 5 (five) years old.b) Acceptance Test :The acceptance test as indicated in the enclosed table (Annexure-V) shall be carried outat the time of inspection of the offered material.c) Routine Test :The routine tests as indicated in the enclosed table (Annexure-V) shall be carried out androutine test certificates / reports shall be submitted to the purchaser’s inspection office at thetime of inspection of the offered material enclosed table (Annexure-V) shall be carried out atthe time of inspection of the offered material.Guarantee :The Pilfer Proof Meter Box should be guaranteed against any manufacturing defects arisingout of faulty design or bad workmanship or component failure for a period of 5 ½ years fromthe date of supply.The meter box found defective within the above guarantee period shall be replaced by theSupplier free of cost within one month of the receipt of intimation of failure/defect. Defectivemeter box are to be replaced by new one with new sl. nos. as allotted by C.E (DTD).Replacement of defective Meter Box :34
The Meter Box declared defective by the WBSEDCL shall be replaced by the supplier up tothe full satisfaction of the WBSEDCL at the cost of supplier as per terms of GCC within 60(sixty) days from the date of intimation by the purchaser. Failure to do so within the time limitprescribed shall lead to imposition of penalty of twice the cost of meter box. The same maylead to black listing even, as decided by WBSEDCL. In this connection the decision ofWBSEDCL shall be final.Inspection :The inspection will be carried out as per inspection & testing clause of General Conditions ofContract (GCC).Guaranteed Technical Particulars :The bidder shall furnish all the necessary information as per Annexure-VI – GuaranteedTechnical Particulars. If the bidder desire to furnish any other information in addition to thedetails as asked for, the same may be furnished.35
Page 5 and 6: h) Operating Frequencyi) Principal
Page 7 and 8: B. Push Button mode :In addition to
Page 9 and 10: Snapshot values of Phase Voltage, P
Page 11 and 12: 20.0 TECHNICAL SUPPORT, MANUALS & T
Page 13 and 14: The exhaustive on-line help should
Page 15 and 16: 5.0 INSPECTION :The purchaser may c
Page 17: 8.0. MANUFACTURING ACTIVITIES:All t
Page 20 and 21: 7. Power Supply The power supply sh
Page 22 and 23: Sl. No. Particular Min. Requirement
Page 24 and 25: Sl. No. Particular Min. Requirement
Page 27 and 28: Annexure - IIISl.No.ComponentFuncti
Page 32 and 33: SCOPE :TECHNICAL SPECIFICATION FOR
Page 36 and 37: ANNEXURE - VLIST OF TESTS TO BE CAR
Page 38: (e) Colour of meter box Grey/Off Wh

Phase 4 â Wire L.T. Solid State ( Static) Whole Current ... - WBSEDCL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Phase 4 â Wire L.T. Solid State ( Static) Whole Current ... - WBSEDCL