Profile cylinders Euromec, Series 168 - Bosch Rexroth

More documents

Recommendations

Info

Base plate for direct mounting of ISO valvesPiston Ø Part no. ValvesizePort nos.1, 2, 4, 3,(5)Port nos.12, 14A B C D E F G H K Weight[kg](lbs)32-125 5801690000 ISO 1 G 1/8 G 1/8 93,5 80 62 35 8 9 20 15 40 0,175(0.386)63,125 5802690000 ISO 2 G 3/8 G 1/8 127 109,5 81,5 46,5 11,5 13 32 29 60 0,580(1.28)Installation InstructionsConnection: Outlet port 2 of the valve should be connected to the end cover where the base plate is fitted.Outlet port 4 is connected to the opposite end cover with tubing.Exhaust ports 3 and 5 are combined in the plate to a common exhaust port.Inlet port 1 and control ports 12 and 14 are located on one side of the plate.Flow: The maximum flow for a valve mounted on these base plates is somewhat lower than for a valve mounted on the subbase.Installation: The plate is fitted directly on the front or rear end cover of the cylinder with a banjo thread. G 1/2 is required.Alternatively one or the other of the two banjo threads (G 1/8 and G 1/4) supplied for base plate 580-169 can be used, depending on the size ofthe cylinder port.A size G 3/8 banjo thread is supplied for base plate 580-269. For cylinders 100 and 125 mm dia., a reducing nipple for the cylinder connectionport G 1/2 is required with Part no. 8631123800.Min. strokes: The table below shows the smallest stroke which a cylinder can have when the base plate is turned towards the opposite end coverand connected with fittings and plastic tubing 6 mm dia. for 580-169 and 12 mm dia. for 580-269.Minimum strokes [mm]Piston Ø Stroke Valve32 50 ISO 140 50 ISO 150 50 ISO 163 100 ISO 1, ISO 280 100 ISO 1, ISO 2100 100 ISO 1, ISO 2125 100 ISO 1, ISO 21
Bosch Rexroth AGPneumaticsUlmer Straße 4DE-30880 LaatzenDeutschlandTel. +49 (0)511-21 36-0Fax. +49 (0)511-21 36-269sales-pneumatics@boschrexroth.dewww.boschrexroth.deBosch Rexroth LimitedPneumaticsBroadway Lane, South Cerney,CirencesterGloucestershire GL7 5UHGreat BritainPhone: +44-12 85-863 000Fax: +44-12 85-863 003info@boschrexroth.co.ukwww.boschrexroth.co.ukBosch Rexroth CorporationPneumatics1953 Mercer roadLexington, KY 40511-1021USAPhone: +1-859-254 80 31Fax: +1-859-254 41 88info@boschrexroth-us.comwww.boschrexroth-us.comBosch Rexroth Canada Corp.Pneumatics3426 Mainway DriveBurlington, Ontario L7M 1A8CanadaTel: +1 905-335-5511Fax. +1 905 335-4184info@boschrexroth.cawww.boschrexroth.caBosch Rexroth Pty. Ltd.Pneumatics23 Iverseb TerraceChristchurchNew ZealandTel. +64 (0011) 643 365 9591Fax. +64 (0011) 643 358 9703Bosch Rexroth Pty. Ltd.Head Office3 Valediction RoadKings Park NSW 2148, SydneyAustraliaTel. +61 (2) 9831-7788Fax. +61 (2) 9831-5553rexeng@rexroth.com.auwww.boschrexroth.com.au006-05-09© This document, as well as the dataspecifications and other informationsset forth in it, are the exclusive propertyof Bosch Rexroth AG. Withouttheir consent it may not be reproduced
Page 1: Electric Drivesand ControlsHydralic
Page 5 and 6: Profile cylinders Euromec, Series 1
Page 7: Profile cylinders Euromec, Series 1
Page 16 and 17: Central male trunnionISO MT4, VDMA,
Page 18 and 19: Bearing bracketsPiston Ø Part no.
Page 20 and 21: Rear end cover clevisISO MP0, VDMA,
Page 22 and 23: Rear eye with PTFE bushing (MP4)ISO
Page 24 and 25: Foot mountingPiston Ø Part no. A B
Page 26 and 27: Bearing block with footPistonØPart
Page 28 and 29: Pivot pin with locking rings for "B
Page 30 and 31: Steel bearing brackets* The maximum
Page 32 and 33: Extra nut ISO 4035Thread KKPart no.
Page 34 and 35: Clevis in stainless steel ISO 8140
Page 36 and 37: Ball eye rod end ISO 8139Thread KK
Page 38 and 39: Profile cylinders, series PRA, PRBA
Page 47 and 48: Sensor mounting for Sensors 275Pist
Page 49 and 50: Cable holderPiston ØPart no.25-100
Page 51: Sub-base for direct mounting of Com

Profile cylinders Euromec, Series 168 - Bosch Rexroth

Create successful ePaper yourself

Delete template?

Save as template?