FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

More documents

Recommendations

Info

Keypad <strong>Operations</strong>:Keypad IllustrationFreq. Ref. Controlled by TM2 or VR Forward Run(Fn_11 = 1 / 2 / 3)RUN/STOP Signal is on Ο Ο Ο Ο Reverse Run(Fn_10 =1) SEQ FRQ FWD REVDISPLAY Hz or Ο Ο Display Voltage ValueRPM Hz/RPM VOLTLight On: Program Mode Ο Ο Display Current ValueFUN AMPRun / Stop RUNDSPLMode Selection KeyCommand KeySTOPFUNCForward / ReverseCommand KeyFWDREV
Parameter ListFunctionFn_xxDescriptionEngineeringUnitsRangeFactorySettingDrive Capacity 0 Drive Capacity Selection 1 1 - 18 *3 23Accel Time 1 Accel Time 1 0.1 sec 0.1 - 3600secDecel Time 2 Decel Time 1 0.1 sec 0.1 - 3600secStop / StartControl TM2ParameterLockout3 xx00 : FWD / STOP, REV / STOPxx01 : FWD / REV, RUN / STOPxx10 : 3-Wire Start / Stop Controlx0xx : REV Command Enablex1xx : REV Command Disable0xxx : Setting Frequency will remain at last Output FrequencywhenInverter stops and Fn_11 = 31xxx : Setting Frequency will be 0 (zero) when Inverter stopsandFn_11 = 34 xxx0 : Enable (Fn_17 - 25)xxx1 : Disable (Fn_17 - 25)xx0x : Enable (Functions except Fn_17 - 25)xx1x : Disable (Functions except Fn_17 - 25)Page10 sec 2310 sec 230000 240000 25V/Hz Pattern 5 V/Hz Pattern Selection 1 0 - 18 9 / 0 25Frequency 6 Frequency Upper Limit 0.01Hz 0 - 400Hz 60 / 50 27Limit 7 Frequency Lower Limit 0.01Hz 0 - 400Hz 0Hz 27Target Speed 8 Target Frequency Setting 0.01Hz 0 - 400Hz 0Hz 27Target SpeedBandwithSTART / STOPSelectionFrequencyCommandSelection9 Frequency Setting DetectionWidth (+ / - F9 / 2)10 0 : Keypad1 : TM20.01Hz 0 - 30Hz 0Hz 2711 0 : Controlled by (Fn_25) Master Reference at Keypad1 : Controlled by Keypad Frequency Setting Potentiometer2 : Controlled by TM2 (Speed Pot)3 : Controlled by Preset Speeds or Multi-Function Inputs(Terminals 6 / 7 / 8)0 280 2815
Page 1 and 2: FM100 Adjustable Speed DriveMainten
Page 3 and 4: ForewordTo fully employ all the fun
Page 5 and 6: Precautions for OperationBefore Tur
Page 7 and 8: Environmental PrecautionsoilAvoid d
Page 9 and 10: General Information:GeneralThe FM10
Page 11 and 12: Basic Specification:1 / 3 Phase 200
Page 13 and 14: Wiring & Remote Operating Functions
Page 15: Function Description for the Main C
Page 19 and 20: FunctionFn_xxDescriptionEngineering
Page 21 and 22: FunctionSkipFrequencyFn_xxDescripti
Page 23 and 24: FunctionFault ContactControl(Contin
Page 25 and 26: Function DescriptionFn_00: Drive Ca
Page 27 and 28: Fn_04:Parameter LockoutParameter Lo
Page 29 and 30: Fn_06:Frequency Upper LimitThe maxi
Page 31 and 32: Fn_12:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx
Page 33 and 34: Fn_24: Jog Speed Reference = 0 - 40
Page 35 and 36: Fn_30: Input Voltage of Power Suppl
Page 37 and 38: Fn_42: Starting Frequency = 0.1 - 1
Page 39 and 40: Fn_48:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx
Page 41 and 42: Note:The Inverter will stop acceler
Page 43 and 44: Fn_65: Skip Frequency 1 0.01Hz ~ 0
Page 45 and 46: During operational conditions where
Page 47 and 48: Fn_78: Overtorque Detection Level:
Page 49 and 50: Fn_82:Energy Savingsxx00: Energy Sa
Page 51 and 52: Fn_85: Process Timer: 1 0.1 sec ~ 0
Page 53 and 54: Fn_102: Communication Parametersxxx
Page 55 and 56: Failure Indication:Faults which can
Page 57 and 58: LV-CLow Voltage1. Input voltage is
Page 59 and 60: Digital Keypad Operation Failure In
Page 61 and 62: NOTE!! Never perform Meg test on co
Page 63 and 64: 230 / 460 Three PhaseDriveEarth Gro
Page 65 and 66: DimensionsWDVOLTFUNAMP0100H230 Volt

FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?