FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

More documents

Recommendations

Info

Fn_10:START / STOP ControlThis parameter is used to decide if the Start and Stop function will be controlled by the Keypad orby Remote Operation (TM2).0: Keypad Control1: Remote Operation (TM2)Note:The STOP Key on the Keypad can still be used for Emergency Stopping even if the START /STOP Control is from TM2 (Fn_10 = 1). (Refer to Fn_48)Fn_11:Frequency Command Selection0: Run by Fn_25 Master Reference1: Run by Frequency Setting Potentiometer on Keypad2: Run by Speed Pot on TM2 or Remote Signal (Terminals (12 / 13 / 14))3: Run by Multi-Function Input Frequency Command (Terminals 6 / 7 / 8))TM2123JP1TM2123JP1TM2123JP1TM2123JP112 13 14 15FM- FM+12 13 14 15FM- FM+12 13 14 15FM- FM+12 13 14 15FM- FM+FCW WIPER FCCW+ -+ -+ -0 - 10VDC Speed Ref. 0 - 5VDC Remote 4 - 20mA Signal 0 - 10VDC Remote(Fn_11) to 2(Fn_11) to 2(Fn_11) to 2(Fn_11) to 2Use a (10K, 2 Watt)For a Remote 5VDCFor a RemoteFor a RemotePot with the wiper inSignal, Jumper (JP1)4 - 20mA Signal,0 - 10VDC Signal,Terminal 13. JumperPins 1 & 2.Jumper (JP1)Jumper (JP2)(JP1) Pins 1 & 2.Pins 2 & 3.Pins 2 & 3.28
Fn_12:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx:0xxx:1xxx:Stall PreventionStall Prevention during Acceleration enableStall Prevention during Acceleration disableStall Prevention during Deceleration enableStall Prevention during Deceleration disableStall Prevention during Running enableStall Prevention during Running disableStall Prevention Decel Time set in (Fn_02)Stall Prevention Decel Time set in (Fn_15)Fn_13: Stall Prevention Level during Accel: 30% - 200%Fn_14: Stall Prevention Level during Run: 30% - 200%Fn_15: Stall Prevention Level during Decel: 0.1 – 3600 secNote:1. If the Acceleration Time in (Fn_01) is set too fast for the size of the load, an Overcurrent Trip“OC-A” may occur during the acceleration period. Setting the proper Stall Prevention Level(Fn_13) during acceleration can automatically extend the ramp time to prevent Overcurrent Tripwhen acceleration time is too short.2. If the Deceleration Time in (Fn_02) is set too short, an Overvoltage “OV” condition may occuron the DC BUS. Setting the proper Stall Prevention Level (Fn_15) during deceleration canprevent an “OV” trip when deceleration time is too short.3. In order to prevent abnormal overload trips during heavy running periods, the Inverter can lowerthe output frequency in accordance with the Deceleration Time set by (Fn_02) or (Fn_15) when(Fn_12) is (1xxx) or when operational current is over the value set in (Fn_14). The Inverter willreturn to its normal operating frequency automatically after the current is back to normalconditions.29
Page 1 and 2: FM100 Adjustable Speed DriveMainten
Page 3 and 4: ForewordTo fully employ all the fun
Page 5 and 6: Precautions for OperationBefore Tur
Page 7 and 8: Environmental PrecautionsoilAvoid d
Page 9 and 10: General Information:GeneralThe FM10
Page 11 and 12: Basic Specification:1 / 3 Phase 200
Page 13 and 14: Wiring & Remote Operating Functions
Page 15 and 16: Function Description for the Main C
Page 17 and 18: Parameter ListFunctionFn_xxDescript
Page 19 and 20: FunctionFn_xxDescriptionEngineering
Page 21 and 22: FunctionSkipFrequencyFn_xxDescripti
Page 23 and 24: FunctionFault ContactControl(Contin
Page 25 and 26: Function DescriptionFn_00: Drive Ca
Page 27 and 28: Fn_04:Parameter LockoutParameter Lo
Page 29: Fn_06:Frequency Upper LimitThe maxi
Page 33 and 34: Fn_24: Jog Speed Reference = 0 - 40
Page 35 and 36: Fn_30: Input Voltage of Power Suppl
Page 37 and 38: Fn_42: Starting Frequency = 0.1 - 1
Page 39 and 40: Fn_48:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx
Page 41 and 42: Note:The Inverter will stop acceler
Page 43 and 44: Fn_65: Skip Frequency 1 0.01Hz ~ 0
Page 45 and 46: During operational conditions where
Page 47 and 48: Fn_78: Overtorque Detection Level:
Page 49 and 50: Fn_82:Energy Savingsxx00: Energy Sa
Page 51 and 52: Fn_85: Process Timer: 1 0.1 sec ~ 0
Page 53 and 54: Fn_102: Communication Parametersxxx
Page 55 and 56: Failure Indication:Faults which can
Page 57 and 58: LV-CLow Voltage1. Input voltage is
Page 59 and 60: Digital Keypad Operation Failure In
Page 61 and 62: NOTE!! Never perform Meg test on co
Page 63 and 64: 230 / 460 Three PhaseDriveEarth Gro
Page 65 and 66: DimensionsWDVOLTFUNAMP0100H230 Volt

FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?