FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

More documents

Recommendations

Info

FunctionDynamicBraking andPriority ofStopping andSpeed Search& AVR ControlFn_xxDescriptionEngineeringUnits48 xxx0 : Enhanced Braking Capacityxxx1 : Standard Braking Capacityxx0x : STOP Key effective in Remote Control Modexx1x : STOP Key ineffective in Remote Control Modex0xx : Speed Search controlled by Terminals on TM2x1xx : Speed Search effective during Inverter Start0xxx : AVR Function effective1xxx : AVR Function ineffectiveRangeAccel / Decel 49 Accel Time 2 0.1 sec 0.1 - 3600secTime 2 50 Decel Time 2 0.1 sec 0.1 - 3600secFactorySettingPage0000 3710.0 sec 3710.0 sec 37Display mode 51 Display Mode Selection 1 0 - 5 0 3752 Engineering Units 1 0 - 9999 1800 37DC Braking 53 DC Braking Time 0.1 sec 0 - 25.5 sec 0.5 sec 3854 DC Braking Injection Freq. 0.1Hz 0.1 - 10Hz 1.5Hz 3855 DC Braking Level 0.1% 0 - 20% 8% 38Multi-FunctionInputsMulti-FunctionOutput56 Multi-Function Input 1(Terminal 6)57 Multi-Function Input 2(Terminal 7)58 Multi-Function Input 3(Terminal 8)00 : SP101 : SP202 : SP303 : Jog04 : Accel / Decel TimeSelection05 : External EmergencyStop06 : External Coast Stop07 : Speed Search00 3801 3802 3859,60 Reserved for Future Use 3861 Multi-Function Output 1(Terminals 10 & 11)00: Run Mode01: At Target Speed02: Set Frequency(Fn_08/09)03 Frequency Detection(Fn_08)62 Reserved for Future Use 04 Frequency Detection(Fn_08)00 4063 Reserved for Future Use 05 Overcurrent Detection 4040404006 Change 00 - 05 (NO) (NC) 4018
FunctionSkipFrequencyFn_xxDescriptionEngineeringUnitsRangeFactorySetting65 Setting Prohibited Freq. 1 0.01Hz 0 - 400Hz 0Hz 41Control 66 Setting Prohibited Freq. 2 0.01Hz 0 - 400Hz 0Hz 4167 Setting Prohibited Freq. 3 0.01Hz 0 - 400Hz 0Hz 41Bandwidth 68 Setting Prohibited Freq. Range 0.01Hz 0 - 10Hz 0Hz 41ElectronicThermalOverloadProtectionReferenceAmpsTorque BoostSlipCompensationOvertorqueControl69 xxx0 : Electronic Thermal Motor Protection enablexxx1 : Electronic Thermal Motor Protection disablexx0x : Electronic Thermal Characteristics in accordancewith a Standard Motorxx1x : Electronic Thermal Characteristics in accordancewith a Special Motorx0xx : Constant TorqueInverter Protection OL : 103% Continuous150% for 60 secondsx1xx : Variable TorqueInverter Protection OL : 113% Continuous123% for 60 seconds0xxx : Coast to Stop after Electronic Thermal MotorProtection is energized1xxx : Operation continued after Electronic ThermalMotor Protection is energizedPage0000 4170 Motor Rated Current 0.1A - Specs. 4171 Torque Boost Selection 4472 Torque Boost Gain 0.1% 0.0 - 10.0% 0.0% 4474 Reserved for Future Use 4475 Motor No Load Current 4476 Motor Rated Slip 0.01Hz 0.00 - 6.00Hz 0.00Hz 4477 xxx0 : Overtorque Detection disablexxx1 : Overtorque Detection enablexx0x : Enable only if at Set Frequencyxx1x : Enable during Operationx0xx : Operation continued after Overtorque is Detectedx1xx : Coast to Stop after Overtorque is Detected0000 4478 Overtorque Detection Level 1% 30 - 200% 160% 4579 Overtorque Detection Time 0.1 sec 0 - 25 sec 0.1 sec 4519
Page 1 and 2: FM100 Adjustable Speed DriveMainten
Page 3 and 4: ForewordTo fully employ all the fun
Page 5 and 6: Precautions for OperationBefore Tur
Page 7 and 8: Environmental PrecautionsoilAvoid d
Page 9 and 10: General Information:GeneralThe FM10
Page 11 and 12: Basic Specification:1 / 3 Phase 200
Page 13 and 14: Wiring & Remote Operating Functions
Page 15 and 16: Function Description for the Main C
Page 17 and 18: Parameter ListFunctionFn_xxDescript
Page 19: FunctionFn_xxDescriptionEngineering
Page 23 and 24: FunctionFault ContactControl(Contin
Page 25 and 26: Function DescriptionFn_00: Drive Ca
Page 27 and 28: Fn_04:Parameter LockoutParameter Lo
Page 29 and 30: Fn_06:Frequency Upper LimitThe maxi
Page 31 and 32: Fn_12:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx
Page 33 and 34: Fn_24: Jog Speed Reference = 0 - 40
Page 35 and 36: Fn_30: Input Voltage of Power Suppl
Page 37 and 38: Fn_42: Starting Frequency = 0.1 - 1
Page 39 and 40: Fn_48:xxx0:xxx1:xx0x:xx1x:x0xx:x1xx
Page 41 and 42: Note:The Inverter will stop acceler
Page 43 and 44: Fn_65: Skip Frequency 1 0.01Hz ~ 0
Page 45 and 46: During operational conditions where
Page 47 and 48: Fn_78: Overtorque Detection Level:
Page 49 and 50: Fn_82:Energy Savingsxx00: Energy Sa
Page 51 and 52: Fn_85: Process Timer: 1 0.1 sec ~ 0
Page 53 and 54: Fn_102: Communication Parametersxxx
Page 55 and 56: Failure Indication:Faults which can
Page 57 and 58: LV-CLow Voltage1. Input voltage is
Page 59 and 60: Digital Keypad Operation Failure In
Page 61 and 62: NOTE!! Never perform Meg test on co
Page 63 and 64: 230 / 460 Three PhaseDriveEarth Gro
Page 65 and 66: DimensionsWDVOLTFUNAMP0100H230 Volt

FM100 Maintenance & Operations Manual - TECO-Westinghouse ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?