Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

4. Installation Procedures10. Place the out board pivot end over main frame with track drive rollers toward the outside. Secure withtwo (2) 3/8" x 1" hex head bolts. Place flat washers on bolt, putting bolt through outboard pivot endand frame, securing with lock washer and nut on the inside (two (2) on each side) then place two (2)3/8" x 1" hex head bolts for 4 auger machine (two (2) 3/8" x 2" for 6 auger machine) up through thebottom of the frame, through the yoke and secure with flat washer, lock washer and nut (two (2) oneach side). (See Figure 4E and Page 50.)Figure 4E11. Thread main power cord and gear motor power cord (14-3) from the inboard pivot through the loopson the side of the main frame, with the main power cord only ending where the large loops stop.The gear motor cord continues to the opposite end of the main frame as shown in Figure 4F.Greenfield shown in photo has been replaced with 14-3 rubber covered wire.Figure 4F18 PNEG-1358 Red Giant Grain Stir-Ator
4. Installation Procedures12. For 6 Auger Units Only: The 6 auger trolley comes in two (2) sections; one 4 auger section plus anextension. First remove the bolts holding the center gearbox on the 4 auger section. (See Figure 4Hor Page 60.) Then, place 2 auger section over 4 auger section and replace gearbox bolts. At this time,install two (2) additional 5/16" x 3/4" hex head bolts, lock washers and nuts in the lapped section.Be sure bolts are tightened securely. Cut loose extension drive shaft. (See Figure 4H.)Figure 4GFigure 4HPNEG-1358 Red Giant Grain Stir-Ator 19
Page 1: Red Giant Grain Stir-AtorModel 176O
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 2. DecalsTHE DECALS SHOWN ON THIS P
Page 13 and 14: 2. DecalsTHE DECALS SHOWN ON THIS P
Page 15 and 16: 4. Installation ProceduresNOTE: Pri
Page 17: 4. Installation ProceduresChain idl
Page 21 and 22: 4. Installation Procedures15. Next
Page 23 and 24: 4. Installation Procedures19. Insta
Page 25 and 26: 4. Installation ProceduresFigure 4V
Page 27 and 28: 4. Installation Procedures25. Take
Page 29 and 30: 4. Installation ProceduresFigure 4A
Page 31 and 32: 4. Installation Procedures28. Assem
Page 33 and 34: 4. Installation Procedures32. After
Page 35 and 36: 5. Bin Wall StressesRead the follow
Page 37 and 38: 6. Overall Size and DimensionsRed G
Page 39 and 40: 7. Parts List1. 4-6 Auger Shields a
Page 41 and 42: 7. Parts List4-6 Auger Shields and
Page 43 and 44: 7. Parts List4-6 Auger Shields and
Page 45 and 46: 7. Parts List4-6 Auger Trolley Base
Page 51 and 52: 7. Parts ListOutboard Pivot End and
Page 53 and 54: 7. Parts ListOutboard Pivot End and
Page 55 and 56: 7. Parts ListCenter Inboard Pivot E
Page 57 and 58: Center Inboard Pivot End - Model 17
Page 59 and 60: Center Inboard Pivot End - Model 17
Page 61 and 62: 7. Parts List6 Auger Trolley Extens
Page 63 and 64: 7. Parts List6 Auger Trolley Extens
Page 65 and 66: 7. Parts ListPinion ShaftsVon Ruden
Page 67 and 68: 7. Parts ListGearbox #129 (104B2134
Page 69 and 70:
7. Parts ListGearbox #150 (104B2135
Page 71 and 72:
7. Parts ListRed Giant GearboxesIde
Page 73 and 74:
7. Parts ListDrawingsFigure 7DFigur
Page 75 and 76:
8. Wiring Diagrams3 Phase - 230 Vol
Page 77 and 78:
8. Wiring Diagrams3 Phase - 575 Vol
Page 79 and 80:
9. OperationsDRYING IN GRAIN DEPTHS
Page 81 and 82:
Operation Recommendations10. Drying
Page 83 and 84:
12. Maintenance and AdjustmentsRed
Page 85 and 86:
12. Maintenance and Adjustments10.
Page 87 and 88:
Stir-Guard13. Red Giant Troubleshoo
Page 89 and 90:
Track Unit1. Drive chain too loose.
Page 91 and 92:
Storage14. Storage and Installation
Page 93 and 94:
15. WarrantyGSI Group, LLC Limited
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?