Red Giant Grain Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

4. Installation Procedures17. Bolt the drive guide arm on to the center inboard pivot and chain idler support yoke, usingthree (3) 1/4" x 3/4" carriage bolts with lock washers and nuts. BE SURE THE GUIDE ARM ISPOSITIONED AS SHOWN IN Figure 4M. (See Page 54.) The bolt holding the guide arm to the chainidler support yoke needs to be positioned with round head of the carriage bolt in the channel of thedrive arm guide.Figure 4M18. Install center drive roller chain with connecting angle to the outside as shown in Figure 4N.CONNECTING ANGLE MUST BE AS SHOWN IN Figure 4N or chain will lock upwhen going around the sprocket and pulleys.To assure proper chain tension, grasp the chain at the halfway point between the sprocket andthe idler pulley. 3/4" Movement each way is all that is advisable at this point. (See Figure 4Nand Figure 7C on Page 73.)Figure 4NFigure 4O22 PNEG-1358 Red Giant Grain Stir-Ator
4. Installation Procedures19. Install motor mount, with support plate, using six (6) 5/16" x 3/4" hex head bolts with lock washers andnuts. Bolt mount bracket in 3 rd hole from the outboard end on trolley side rail. BE SURE MOUNTINGPLATE IS ON THE SAME SIDE AS ELECTRICAL CORDS. (See Figure 4P and Page 44.)Figure 4P20. Top drive shaft assembly. First place two (2) BX-48 matched V-belts on the 11-3/8" pulley. Thensecurely bolt top drive shaft assembly on to the trolley, using four (4) 5/16" x 3/4" bolts, with lockwashers and nuts. Place the 11-3/8" pulley toward the outboard end of the main frame, as shown inFigure 4Q or See Page 44. Be sure the belt idlers are opposite the motor mount.Figure 4QFigure 4RPNEG-1358 Red Giant Grain Stir-Ator 23
Page 1: Red Giant Grain Stir-AtorModel 176O
Page 6 and 7: 1. SafetySafety InstructionsOur for
Page 9 and 10: 1. SafetyWear Protective ClothingWe
Page 11 and 12: 2. DecalsTHE DECALS SHOWN ON THIS P
Page 13 and 14: 2. DecalsTHE DECALS SHOWN ON THIS P
Page 15 and 16: 4. Installation ProceduresNOTE: Pri
Page 17 and 18: 4. Installation ProceduresChain idl
Page 19 and 20: 4. Installation Procedures12. For 6
Page 21: 4. Installation Procedures15. Next
Page 25 and 26: 4. Installation ProceduresFigure 4V
Page 27 and 28: 4. Installation Procedures25. Take
Page 29 and 30: 4. Installation ProceduresFigure 4A
Page 31 and 32: 4. Installation Procedures28. Assem
Page 33 and 34: 4. Installation Procedures32. After
Page 35 and 36: 5. Bin Wall StressesRead the follow
Page 37 and 38: 6. Overall Size and DimensionsRed G
Page 39 and 40: 7. Parts List1. 4-6 Auger Shields a
Page 41 and 42: 7. Parts List4-6 Auger Shields and
Page 43 and 44: 7. Parts List4-6 Auger Shields and
Page 45 and 46: 7. Parts List4-6 Auger Trolley Base
Page 51 and 52: 7. Parts ListOutboard Pivot End and
Page 53 and 54: 7. Parts ListOutboard Pivot End and
Page 55 and 56: 7. Parts ListCenter Inboard Pivot E
Page 57 and 58: Center Inboard Pivot End - Model 17
Page 59 and 60: Center Inboard Pivot End - Model 17
Page 61 and 62: 7. Parts List6 Auger Trolley Extens
Page 63 and 64: 7. Parts List6 Auger Trolley Extens
Page 65 and 66: 7. Parts ListPinion ShaftsVon Ruden
Page 67 and 68: 7. Parts ListGearbox #129 (104B2134
Page 69 and 70: 7. Parts ListGearbox #150 (104B2135
Page 71 and 72: 7. Parts ListRed Giant GearboxesIde
Page 73 and 74:
7. Parts ListDrawingsFigure 7DFigur
Page 75 and 76:
8. Wiring Diagrams3 Phase - 230 Vol
Page 77 and 78:
8. Wiring Diagrams3 Phase - 575 Vol
Page 79 and 80:
9. OperationsDRYING IN GRAIN DEPTHS
Page 81 and 82:
Operation Recommendations10. Drying
Page 83 and 84:
12. Maintenance and AdjustmentsRed
Page 85 and 86:
12. Maintenance and Adjustments10.
Page 87 and 88:
Stir-Guard13. Red Giant Troubleshoo
Page 89 and 90:
Track Unit1. Drive chain too loose.
Page 91 and 92:
Storage14. Storage and Installation
Page 93 and 94:
15. WarrantyGSI Group, LLC Limited
show all

Red Giant Grain Stir-Ator - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?