Installation Manual - GTO/Pro

More documents

Recommendations

Info

DrillLevelDrill BitPliersClampsSmall, Medium, LargePenHack SawOpen End WrenchesPhillips HeadScrewdriverAdjustableWrenchWireStripper8. Materials You may Need for the Installation:Depending on the type of gates and posts, you may need some additional materials/hardware.CenterPunchFlat HeadScrewdriverHammerSmallFlat HeadTapeMeasure7. Tools Needed• Power Drill • Pliers• Level • Tape Measure• Wire Strippers • Center Punch• Open End Wrenches: 9/16” and 3/4”• Drill Bits: 3/8” and 1/2”• Hacksaw or Heavy Duty Bolt Cutters• Small (Flat Head) Screwdriver• Phillips Screwdriver• C-Clamps: small, medium, and large• Adjustable Wrench• Extra person will be helpful• Low voltage wire [RB509]. Length depends upon the distance between the transformer powersupply and the control box. (Page 16)• If the gate is more than 1000’ away from an AC power source you will need to use at least one 10watt Solar Panel [FM123] to trickle charge the battery. (Page 2)• PVC Conduit. (Page 7)• The diameter of the post should be at least 6” in order to mount the post bracket. (Page 7)• Depending upon the diameter of the post, you may need longer bolts than those provided. Boltsshould be at least 1” longer than the diameter of the post. (Page 7)• Metal plate for wooden posts. (Page 7)• A horizontal or vertical cross members or mounting plates may be needed to mount the operatorsto the gates. (Page 3)• Some types of installations require U-Bolts. (Page 11)• Surge protection for transformer. (Page 18)• Weatherproof cover for transformer if installed outside. (Page 18)• For push-to-open applications you must have two (2) PTO Brackets [R4388).IMPORTANT:The 3000XLS gate operator (6 ft. cable) will be installed on the gate on the sameside of the driveway as the control box and they will be referred to as the MASTERgate and gate operator. The 3200XLS gate operator (40 ft. cable) will be installed onthe gate on the opposite side of the driveway from the control box and they will bereferred to as the SECOND gate and gate operator throughout this manual.6 GTO 3000XLS/3200XLS Instruction Manual © 01.10.12
9. Installation OverviewPull-To-Open Gates (Gate Opens into the Property)The diagram shown below is an example of a Pull-To-Open installation on a chain link fence and dualgate. Mounting the operators on masonry columns requires special procedures; see Column InstallationInformation on page 27. Furthermore, if you have a Push–To–Open gate, see Push–to–Open Installationon page 25 before proceeding.ReceiverGate Swings Evenly and FreelyHung Firmly and PlumbControl Box with Battery120 Volt IndoorTransformerPost Bracket AssemblyMASTER Gate OpenerSECOND Gate Opener(surge protectornot supplied)Gate Bracket6' Power CableClosed Position Stop PlatesRun 1000' (max.) of lowvoltage wire to controlbox from transformer(wire not included).PVC conduit (not included)to protect second openerpower cable and low voltage wirefrom lawn mowers and weed eaters.Concrete PouredAround Gate PostInstall the Master Gate Operator (3000XLS)Install the Post Bracket AssemblyThe post bracket is designed to work on a flat post. Postsmust be at least 6” square in order to bolt the post bracket.When using bolts to mount the post bracket, the bolts mustcompletely penetrate the post.• The best method of attaching the post bracket to ametal post is welding.• If your post exceeds 8”, it will be necessary to use hexhead bolts longer than those supplied.• Round wood posts (no smaller than 8” diameter) maybe notched to create a flat surface for attaching thepost bracket.• Wood posts will require a metal plate (not provided)between the nuts and post to prevent the operatorfrom pulling the bolts and washers through the wood.• A post smaller than 6” in diameter should be madeof metal instead of wood so that it will remain stablewhile the operator is moving the gate.• Masonry columns will require masonry anchors/hardware (not provided).GTO 3000XLS/3200XLS Instruction Manual © 01.10.12 7
Page 3 and 4: Table of ContentsClass Rating......
Page 11: Technical SpecificationsGTO/ACCESS
Page 14 and 15: 5. 3000XLS Parts ListCONTROL BOX AN
Page 18 and 19: Step 1Close the gate and place your
Page 20 and 21: Step 8Remove the clevis pin from th
Page 22 and 23: Mount VerticallyNOTE: The optional
Page 25 and 26: Connecting MASTER OperatorStep 3Ins
Page 27 and 28: Step 5Strip 3/16” off the ends of
Page 30 and 31: Step 7Press the transmitter once ag
Page 32 and 33: DIP SwitchesDIP Switch Settings (MO
Page 34 and 35: Wiring AccessoriesGTOTRANSFLOCKPWRA
Page 36 and 37: Set Control Board for Push-To-OpenM
Page 38 and 39: Troubleshooting GuideIf your gate o
Page 40 and 41: Repair ServiceIf your GTO 3000XLS/3
Page 42 and 43: 1 2 3ABC DEF4 5 6GHI JKL MNO7 8 9PR
Page 44: ACCESSSYSTEMSPROFESSIONAL RESIDENTI

Installation Manual - GTO/Pro

Create successful ePaper yourself

Delete template?

Save as template?