cb-obs411 electrical mechanical data sheet - SE Spezial-Electronic ...

More documents

Recommendations

Info

connectBlue7 Bluetooth Information7.1 General informationIn the tables below you can find information about Bluetooth properties. The output power of the cB-OBS411 device is max +4dBm(2.5mW).Table 10: Bluetooth information cB-OBS411ParameterBluetooth radioHost micro controllerRF output power(conducted - excluding antenna gain)DataST-Ericsson STLC2500DBST Microelectronics STM32F10xClass 1, max 4dBmReceive sensitive levelReceive input level (max)Output frequencyBluetooth stackBluetooth qualification-84dBm+15dBm2.402 - 2.480 GHz, ISM band.connectBlue Embedded Bluetooth Stack2.1+EDR7.2 Bluetooth Qualification informationAll products based on the PCB cB-0925 have been qualified according to the Bluetooth specification 2.1+EDR.Table 11: Bluetooth Qualification informationModule Bluetooth specification Referenced QDIDs List date (EPL)cB-OBS411 2.1+ EDR B016013 combined with B015102 2009-10-26The following Bluetooth profiles are supported (covered functionality):Generic Access Profile (GAP)Serial Port Profile (SPP)Dial-up Networking Profile (DUN GW, DUN DT)When creating end products based on the cB-OBS411 the following applies:The end product does not have to be re-tested or re-qualified.A free of charge Bluetooth End Product Listing (EPL) must be completed at the Bluetooth SIG website www.bluetooth.org. Thisapplies for all products implementing Bluetooth technology. The EPL requires no testing (online listing only) and is goodmarketing since the product is published at the Bluetooth web site www.bluetooth.com. A free of charge "Adopter Bluetooth SIGmembership" is required.Create the EPL based on the connectBlue cB-OBH411 (QD ID: B016013) combined with the connectBlue Embedded BluetoothHost Stack (QD ID:B015102). A guide describing each step in the end product listing process is available in the connectBlueBluetooth Qualification Guide.The Bluetooth Trademark may be placed on the end product. This requires a free of charge Adopter Bluetooth SIG membership.For more information see www.bluetooth.orgThe Bluetooth Trademark may be used in material related to the end product. This requires a free of charge Adopter BluetoothSIG membership. For more information see www.bluetooth.org.Copyright © 2010 connectBlue AB Page 24 of 42
connectBlueFor more information please contact connectBlue.Copyright © 2010 connectBlue AB Page 25 of 42
Page 1 and 2: connectBlueCB-OBS411 ELECTRICAL MEC
Page 3 and 4: connectBlue2 IntroductionThe hardwa
Page 5 and 6: connectBlue2.3 Block DiagramFigure
Page 7 and 8: connectBlue3.1 Pin Numbering3.1.1 J
Page 9 and 10: connectBlue13 - 8 - GREEN/Switch-1
Page 11 and 12: connectBlueR IN_PULL-UPInput signal
Page 13 and 14: connectBlue5 Antennas5.1 Surface Mo
Page 15 and 16: connectBlue5.2.2 AntennasPart Numbe
Page 17 and 18: connectBluePartNumberNamecB-ACC-17R
Page 19 and 20: connectBlue6 Mechanics6.1 Module Ou
Page 21 and 22: connectBlueFigure 9: Host PCB layou
Page 23: connectBlueThe modules are produced
Page 27 and 28: connectBlue8.3 FCC and IC Complianc
Page 29 and 30: connectBlue9 Guidelines for Efficie
Page 31 and 32: connectBlue10.2.1.2.2 Module output
Page 33 and 34: connectBlue10.2.2.2 External RS232
Page 35 and 36: connectBlueFigure 17: A complete RS
Page 37 and 38: connectBlueFigure 21: A red LED in
Page 39 and 40: connectBlueFigure 25: No restore sw
Page 41 and 42: connectBlueFigure 30: A reset switc

cb-obs411 electrical mechanical data sheet - SE Spezial-Electronic ...

Create successful ePaper yourself

Delete template?

Save as template?